SPECIFICATIONS (規格書) 編 號 NO. 12 JAN 2012 ： F-J08K-01-003 型 號 名 稱 Model Name ： FJ08KS-10 B10K-2 L6.6Hx3 日 期 :2012 年 1 月 12 日 一 、 ELECTRICAL CHARACTERISTICS 電 氣 特 性 序號 項 目 性 能 NO.
The rated power should be changed according to the following chart when the ambient temperature changed. 它與環境溫度按以下曲線變化。 Derating curve of rated dissipation 4 Rated power 額定功率 Contact Noise 接觸雜音 (CRV) 5 Linear Taper B: B 型: 0.0125W 0.0125W By the test length of less than 90% carbon film length。 測試長度小於碳膜長度的 90%。 / / Voltage divider error is defined the ratio of the voltage terminals 1-2 to terminals 1-3 after the slide bars rested. 5V D.C.
1 Figure of the slid bars operation 滑柄動作形式 Slides on the 2D flat 平面移動的形式 2 The stopper strength of the slid bars 滑柄止動強度 More than 3.0Kgf 3 seconds min 大於 3.0Kgf，至少 3 秒鐘 Apply side force on the slid bars perpendicular to the slid bars’s axial direction. 垂直於滑柄的力作用於滑柄上. 3 Rotational Stopper Strength of the slid bars 滑柄旋轉止動 強度 150gf.cm Min There should be no visual damage when minimum 150gf.cm of torque are applied. The slid bars to be operated mechanically 當其承受小於 150gf.
9 10 Accuracy of reset position of slide bars 滑柄復歸精度 Terminal strength 端子強度 Measure the distance between the center of the slide bars and the center after the slide bars pushed to the any direction on the 2D flat and resets. 測量滑柄的中心和滑柄在 2D 平面推向任 何方向後復歸的中心的距離. ±0.2 mm Push the slide bars to any direction 推動滑柄向任何方向 A force of 3N (306gf)being applied in Without damage or excessive one direction at the tip of the terminal looseness of terminals or poor for one minute and only one time to each contact.
3 4 5 6 Cold 耐寒性 Damp heat 耐濕性 The total resistance change should be within ±20%. To be operated mechanically. 全阻值變化要在±20%以內， 機械方面能動作。 Insulation resistance: more than 10M Ω with 250V insulation resistance tester. The total resistance change should be within ±20%. To be operated mechanically. 用 250V 絕緣測試機測試，絕緣阻 抗 10MΩ以上, 全阻值變化要在±20%以內, 機械方面能動作.
Resistance to soldering heat 焊錫耐 熱性 7 Number of cycles 耐久次數值 8 Variation of total resistance shall be within ± 5%, and terminals shall not work loose to injure electric contact, after test. 全阻值變化±5%以內,測試後無 端子鬆動,不會損壞電氣接點。 Total resistance ≦ Initial value±20%. No mechanical malfunction. 全阻值變化≦初始值±20% . 機械方面能動作. Solder dip:浸焊 Preheating condition: Surface temperature of the substrate shall be settled within 100℃ in one min. 預熱: 基板表面溫度 100℃以下，1 分鐘 內。 Solder temperature 260±5℃for 5 sec.
4 5 Circuit diagram 電路圖 Contact resistance 接觸阻抗 Insulation 6 resistance 絕緣阻抗 / Apply 2 times of the operating force of the static load on the vertical direction of the lever, measure the resistance by using the Contact Resistance Tester with 1KHZ, 20mV, 5~50mA of current. 將兩倍於作動力之靜負荷加於操作柄之 中央以(1KHZ,20mV, 5~50mA)微電流接觸 阻抗計測定. Less than 300 mΩ 低於 300 mΩ More than 100 100 MΩ以上 A voltage of DC100V is applied between terminals. MΩ 以 DC100V 之電壓加於端子間測定.
If there is any doubt arise from judgement ,test shall be conducted at the following conditions: 遇有疑慮時,則測試應在以下狀態下進行: Ambient temperature 溫度 20°C ±2°C Relative humidity 相對濕度 60% to 70% Air pressure 氣壓 86 KPa to 106 KPa 3 Operating temperature range 使用溫度範圍 -10°C to +55°C 4 Storage temperature range 儲存溫度範圍 -30°C to +80°C 2 六 、 Appearance,Style and Dimensions ,Type of actuating ,Contact arrangement 外觀、形狀和尺寸、動作形式、回路形式 序號 NO 1 項 目 ITEM Appearance 外觀 F-J08K(S) shall be no defects that affect the se
