Instructions / Assembly

ManualsBrandsUnbranded ManualsCeiling Fans55 in. Industrial White Down rod Ceiling Fan with Wall Control

OWNER’S MANUAL

READ AND SAVE THESE INSTRUCTIONSREAD AND SAVE THESE INSTRUCTIONS

Attention: Pictures in the IM are for reference only.

Important safety instructions

INSTALLATION INSTRUCTIONS

AND

INSTALLATION INSTUCTION

Ceiling Fans

MODEL: FC140-BAA

PRECAUTIONS

Check components for

completeness after

unpacking.

The mark indicates the

grounding terminal that

requires proper grounding.

Never connect the power

before connecting the Speed

Controller to electrical shock.

Fan blades are fine-tuned in

the factory before shipping;

do not squeeze it or alter the

angle arbitrarily. For batch

installation, do not mix up

components of several fans

or their performance and flow

rate may be affected.

Make sure the suspension rod

is fixed firmly. For the sake of

safety, he bottom of the Fan

Header must be at least 3.05m

above the floor.

Check voltage of power source

for compliance with voltage

indication of the unit before use.

To install ceiling fans, use only

original suspension rods (with

shaft sleeve) assembled by

our factory. Any alteration is

strictly forbidden. Any adverse

effect resulting from the

customer’s arbitrary

modification is the sole

responsibility of the customer.

If the fan is installed in

environments where the level

of airborne fibers or dust

severely exceed standards,

such as in factories or garages,

special ceiling fans with dust

prevention shaft or dust

prevention devices must be

ordered; otherwise noise or

seizure may occur after a

certain period of operation.

Installation and maintenance

of ceiling fans must be carried

out by the manufacturer or

maintenance professionals or

similar.

Power wiring must be fixed

safely and firmly to prevent

loose contact. Prevent

contact with the fan blades

to prevent accidents.

FRIM

The fan requires little maintenance. Do not try to fix it by yourself.

Refer it to qualified service personnel if service is needed.

Before cleaning and assembling, fan must be switch power off.

. To ensure adequate air circulation to the motor, keep vents at the rear

of the motor free of dust. Do not disassemble the fan to remove dust.

3. Please wipe the exterior parts with a soft cloth soaking a mild

detergent.

4. Do not use any abrasive detergent or solvents to avoid scratching the

surface.

Do not use any of the following as a cleaner: gasoline, thinner.

5. Do not allow water or any other liquid into the motor housing or interior

parts.

1. Be sure switch power off from the electrical supply source before

cleaning.

2. Plastic parts should be cleaned with a soft cloth moisten with mild soap.

Thoroughly remove soap film with dry cloth.

DISPOSAL：Do not dispose of electrical appliances as unsorted

municipal waste, use separate collection facilities. Contact your local

government for information regarding the collection systems available. If

electrical appliances are disposed of in landfills or dumps, hazardous

substances can leak into the groundwater and get into the food chain,

damaging your health and well-being.

Questions, problems, missing parts? Before returning to the store call

Home Depot Customer Service

8 a.m.- 7p.m,EST,Monday-Friday,9 a.m.- 6 p.m,EST Saturday

1-877-527-0313

HOMEDEPOT.COM

MAINTENANCE INSTRUCTION

CLEANING

1.WARNING -To Reduce The Risk Of Fire Or Electric Shock, Do Not

Use This Fan With Any Solid-State Speed Control Device.”

2.WARNING - To Reduce The Risk Of Personal Injury, Do Not Bend

The Blade Brackets When Installing The Brackets, Balancing The

Blades, Or Cleaning The Fan. Do Not Insert Foreign Objects In

Between Rotating Fan Blades.”

3.WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer. If

you have questions,contact the manufacturer.

b) Before servicing or cleaning unit, switch power off at service panel

and lock the service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warning device, such as

a tag, to the service panel.

c) Installation work and electrical wiring must be done by qualified

person(s) in accordance with all applicable codes and standards,

including fire-rated construction.

d) Sufficient air is needed for proper combustion and exhausting of

gases through the flue (chimney) of fuel burning equipment to prevent

back drafting. Follow the heating equipment manufacturer’s guideline

and safety standards such as those published by the National Fire

Protection Association (NFPA), and the American Society for Heating,

Refrigeration and Air Conditioning Engineers (ASHRAE), and the local

code authorities.

e) When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

4.WARNING - To Reduce The Risk Of Fire, Electric Shock, Or

Personal Injury, Mount Directly To A Structural Framing Member

5.CAUTION- To Reduce The Risk Of Injury To Persons, Install Fan So

That The Blade Is At Least 3.05 Meters (10 Feet) Above The Floor.

INSTALLATION INSTRUCTIONS - CEILING FAN

NOTICE: To ensure the success of this installation, be sure to read the

instructions and review the diagram thoroughly before beginning.

IMPORTANT SAFETY NOTICE

Installation shall be carried out in accordance with the National

Electrical Code (ANSI/NFPA 70), Canadian Electrical Code and local

codes.

WARNING – Make sure power is off before attempting installation.

CAUTION- To Reduce The Risk Of Injury To Persons, Install Fan So

That The Blade Is At Least 3.05 Meters (10 Feet) Above The Floor.

1. Install the ceiling fan hook (Figure 1) directly to building structure by

using the two screws provided.

2. Release six M6 blade screws on the fan head, then fix the fan

blades by fastening screws (Figure 2).

3. Hang the ceiling fan onto the hanger hook fixed on the building

structurer(Fig. 3).

4. Install the wall-mounted controller onto the wall type outlet box (Fig.

4).

5. Connect circuit according to circuit diagram. To be ensure the

controller is connected in the line circuit.

6. After completing connection of circuit, check all fixing screws are

fastened well in order to ensure the ceiling fan fixed well on the

building structurer.

OPERATION INSTRUCTIONS

Remote regulator for ceiling fan is supplied for installation. It is

turned counter-clockwise from the mark “5” to “1” indicating the

speed from fast to slow while turning clockwise from “1” to “5”

indicating from slow to fast. And “0” means off.

4 5 6

Fig.1 Fig.2

Fig.3 Fig.4

Shock absorber wheel

Hanger clip

Downrod

A hook

Elastic washer

Flat washer

Canopy

Lower Canopy

Pin, nut, elastic washer,

flat washer

Screw

Capacitance

Screw

Nose

Blade

Regulator

Wall Switch(on/

off)

Ceiling fan

Earth

Terminal terminal

NOTICE: The downrod cannot change length.