Installation Guide

DUAL OUTLET AIR SWITCH KIT FOR GARBAGE DISPOSAL
& OPTIONAL HOT WATER DISPENSER
1) Positioning the push button switch. Remove
LARGE plastic nut from the air switch main threads
and insert into existing standard sink hole leaving
the gasket above the sink/counter. If a hole does
NOT exist, drill a 1 ¼" diameter hole into the counter
where you want the button to go.
3) Attach the tubing to the outlet. Mount the module with the 2 screws BEFORE
connecting the tubes (optional). Follow the previous step to connect the tubing
to the outlet on the side of the module by removing the small plastic nut,
inserting tube and threading/tightening.
4) Installing/connecting the power module. Once the air switch and tubing
are connected, you can plug the module power cord into your existing power
outlet. The garbage disposer can then plug into the top outlet. The disposer
may turn on. If it does, engage your air switch to shut off. The secondary can be
used optionally for your hot water dispenser. Note - BOTH OUTLETS ARE NEVER ON
AT THE SAME TIME. The secondary outlet is on an alternating switch and shuts off
when the air switch engages the disposal, then reengages when shut off.
2) Attach the tubing to push button. Once you
have determined a good place for the switch,
remove the small plastic nut at the bottom of the
switch and insert the plastic tubing into the opening
at the bottom of the switch, then push the plastic nut
onto the tube and thread/tighten onto bottom nut
of air switch. (Attaching the tube now allows you to not have to attach the
tubing from under the sink). Fish the tubing and switch through the sink or
counter hole. Thread/tighten LARGER plastic nut from Step 1 from UNDER the sink
or counter making a watertight and secure seal for the switch.
Push Button
Disposer
AC Power Plug
AC Power Plug
Black PVC Air Tubing
Instant Hot Water
Dispenser
Faucet
Dispenser Tank
(Optional)
Air Control
Transmitter
Rubber
Gasket
Sink/Counter
Hole
Plastic Nut
Power
Module
Wall Outlet
DUAL OUTLET AIR SWITCH KIT FOR GARBAGE DISPOSAL
& OPTIONAL HOT WATER DISPENSER
1) Positioning the push button switch. Remove
LARGE plastic nut from the air switch main threads
and insert into existing standard sink hole leaving
the gasket above the sink/counter. If a hole does
NOT exist, drill a 1 ¼" diameter hole into the counter
where you want the button to go.
3) Attach the tubing to the outlet. Mount the module with the 2 screws BEFORE
connecting the tubes (optional). Follow the previous step to connect the tubing
to the outlet on the side of the module by removing the small plastic nut,
inserting tube and threading/tightening.
4) Installing/connecting the power module. Once the air switch and tubing
are connected, you can plug the module power cord into your existing power
outlet. The garbage disposer can then plug into the top outlet. The disposer
may turn on. If it does, engage your air switch to shut off. The secondary can be
used optionally for your hot water dispenser. Note - BOTH OUTLETS ARE NEVER ON
AT THE SAME TIME. The secondary outlet is on an alternating switch and shuts off
when the air switch engages the disposal, then reengages when shut off.
2) Attach the tubing to push button. Once you
have determined a good place for the switch,
remove the small plastic nut at the bottom of the
switch and insert the plastic tubing into the opening
at the bottom of the switch, then push the plastic nut
onto the tube and thread/tighten onto bottom nut
of air switch. (Attaching the tube now allows you to not have to attach the
tubing from under the sink). Fish the tubing and switch through the sink or
counter hole. Thread/tighten LARGER plastic nut from Step 1 from UNDER the sink
or counter making a watertight and secure seal for the switch.
Push Button
Disposer
AC Power Plug
AC Power Plug
Black PVC Air Tubing
Instant Hot Water
Dispenser
Faucet
Dispenser Tank
(Optional)
Air Control
Transmitter
Rubber
Gasket
Sink/Counter
Hole
Plastic Nut
Power
Module
Wall Outlet