SDS

Nisus DSV Specimen Label • SAL102110 • page Page 14 of 18
every other hour basis. If this is done, fog for 30-90 se-
conds once per hour or once every two hours. When
fogging is complete, ventilate buildings, and other closed
spaces. Do not house livestock or employ equipment
until treatment has been absorbed or dried. Thoroughly
scrub all treated feed racks, mangers, troughs, automat-
ic feeders, fountains and waterers with soap or deter-
gent, and rinse with potable water before reuse. Only for
treatment of setters and hatchers after poultry/
chicks/eggs have been removed. Not for treatment of
hatchers which contain chicks/eggs.
Note: The fog generated is irritating to the eyes, skin
and mucous membranes. Under no circumstances must
a room or building be entered by anyone within two
hours of the actual fogging and a minimum of 4 air ex-
changes (ACH) per hour in the facility. If the building
must be entered, then the individuals entering the build-
ing must wear a self-contained respirator approved by
NIOSH/MSHA, goggles, long sleeves and long pants.
FOGGING IS TO BE USED AS AN ADJUNCT TO AC-
CEPTABLE MANUAL CLEANING AND DISINFECT-
ING OF ROOM AND MACHINE SURFACES.
BARBER/SALON
DISINFECTION / FUNGICIDE / VIRUCIDE* FOR BAR-
BER / SALON TOOLS DIRECTIONS: Immerse pre-
cleaned barber/salon tools such as combs, brushes,
plastic rollers, razors, clipper and trimmer blades, twee-
zers, manicure/pedicure tools, clippers, scissors and
other hard, non-porous salon instruments and tools in a
2 oz. per gallon of water solution. Completely immerse
instruments and tools for at least 10 minutes. Rinse
thoroughly and dry before use. Prepare a fresh solution
at least daily or more often if solution becomes visibly
dirty.
DISINFECTING / FUNGICIDE / VIRUCIDE* GROOM-
ING CLIPPERS: Remove hair, dandruff and dust parti-
cles prior to disinfecting the blades. Turn the clipper off
occasionally during use and spray between the teeth of
blades with a solution of 2 oz. per gallon of water. Allow
surface to remain wet for at least 10 minutes. Rinse sur-
faces thoroughly. Then wipe dry with a clean soft cloth.
CLEANING HAIR CLIPPERS AND ELECTRIC
SHEARS: While clipper/shear is running, hold in the
downward position and spray 1 1/4 oz. per gallon of wa-
ter solution of this product directly onto the blades two or
three times to thoroughly wet the blades. Do not spray
on the clipper case or drip into clipper housing. Turn off
clipper/shear. Allow surface to remain wet for at least 10
minutes. Rinse surfaces thoroughly. Then wipe dry with
a clean soft cloth. Lubricate as per clipper/shear manu-
facturer’s instructions.
CLEANING BARBER / SALON SHEARS AND OTHER
IMPLEMENTS: Spray shear/implement until thoroughly
wet. Wipe away visible debris using a soft bristle brush
or cloth. Turn off clipper/shear. Immerse pre-cleaned
shear/implement into a container of a 1 1/4 oz. per gal-
lon of water solution of this product for at least 10
minutes. Rinse surfaces thoroughly. Remove shear/ im-
plement and wipe dry. Use fresh solution at least daily
or when immersion tank solution becomes visibly dirty.
Note: Plastic instruments can remain immersed until
ready to use. Stainless steel shears and other metal
instruments must be removed after 10 minutes, rinsed,
dried, and kept in a clean non-contaminated receptacle.
Prolonged soaking will cause damage to metal
instruments.
DISINFECTION / FUNGICIDE / VIRUCIDE* OF HARD,
NON-POROUS SURFACES IN FOOTBATHS: To re-
move body oils, dead tissue, soil and all other buildups
or organic matter on inanimate surfaces after using the
footbath, drain the water and thoroughly clean all hard,
non-porous surfaces with soap or detergent, then rinse
with water. Saturate surfaces with a use solution of 2 oz.
per gallon of water to exposed surfaces with a brush,
cloth, mop, sponge or mechanical spray device. Brush or
swab thoroughly and allow solution to stand for 10
minutes. For spray applications, use a coarse pump or
trigger spray device. Do not breathe spray. After the unit
has been thoroughly disinfected, rinse all cleaned sur-
faces with fresh water. Do not use equipment until
treatment has been absorbed, set or dried.
RESTROOM/BATHROOM
NON-ACID TOILET BOWL, URINAL & BATHROOM
DISINFECTANT / CLEANER DIRECTIONS
FROM CONCENTRATE: Remove gross filth prior to
disinfection. Add 1 1/4 oz. of this product directly into
the toilet bowl and mix. Brush thoroughly over exposed
surfaces and under the rim with a brush, cloth, mop,
sponge or mechanical spray device. Repeat and allow
solution to stand for 10 minutes and flush.
FROM USE SOLUTION: Pre-clean surface. Empty wa-
ter out of toilet bowl or urinal and apply a 2 oz. per gallon
use solution to exposed surfaces including under the rim
with a brush, cloth, mop, sponge or mechanical spray
device. For sprayer application, use a coarse pump or
trigger spray device. Brush or swab thoroughly and al-
low solution to stand for 10 minutes and flush. Refill toi-
let bowl or urinal with water.
FOR HEAVY DUTY CLEANING: Pre-clean surface.
Empty toilet bowl or urinal of water and apply 8-12 ounc-
es of use solution to exposed surfaces including under
the rim with a brush, cloth, mop, sponge or mechanical
spray device. Brush or swab thoroughly and allow solu-
tion to soak to aid in soil removal. For sprayer applica-
tion, use a coarse spray device and swab all areas after
spraying. Refill toilet bowl or urinal with water.
FOR USE TO CLEAN AND DISINFECT SHOWER
ROOMS, LOCKER ROOMS AND OTHER LARGE
OPEN AREAS WITH FLOOR DRAINS:
1. Pre-clean heavily soiled areas.
2. Apply use solution of 1 1/4 oz. of this product with
one gallon of water to floors, walls and ceilings,
making sure not to over spray. To disinfect, all
surfaces must remain wet for 10 minutes. Special