Installation Guide

Sink Care and Cleaning
This sink has been specifically designed and engineered to exceed demanding strength and stress factors required for use. It is stain
resistant, semi gloss finish. Like any fine finish, it requires reasonable care to maintain its beauty and luster. Day-to-day cleaning: Wash with
warm water, a soft cloth, and mild liquid detergent. For stubborn stains: Use a Non-Abrasive, liquid detergent cleaner, applied using a soft
cloth. More persistent stains, tar, or paint can be removed with naptha or mineral spirits. Remove excess plaster by scraping with a sharpened
soft wood stick. Avoid wire brushes, metal scrapers, or tools. NEVER USE ABRASIVE SCOURING POWDERS, SOLVENT BASED
CLEANSERS, OR SCOURING PADS AS THEY TEND TO DULL THE FINISH.
FIAT PRODUCTS
®
LIMITED ONE YEAR WARRANTY
AS America, Inc. offers a limited warranty on FIAT Products to the original Purchaser consumer, both residential and commercial that products
of its own manufacture shall be free of defects in material and workmanship for a period of One Year.
Under this warranty FIAT Products will, at its sole discretion, upon receipt of a written claim and proof of purchase, either (1) repair the
product, (2) replace the product or any part therein with a FIAT Product of equal or similar type and size, or (3) refund to the consumer the
wholesale price of the product received by FIAT Products. If FIAT Products elects to refund the wholesale price to the consumer, FIAT
Products shall have no further obligation to its wholesale customer, or any contractor with respect to such product. Goods proven to be
defective will be replaced after proper inspection, but no claims for damages incurred or for work done thereon will be allowed. Replace-
ments when supplied will be shipped at no cost to the consumer.
This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of the product
should check with a local building or plumbing contractor to ensure local code compliance before installation.
This warranty will be void if:
1) the product has been moved from its initial place of installation; 2) if it has been subjected to faulty maintenance, abuse, misuse, accident
or other damage; 3) if it was not installed in accordance with FIAT Products instructions; or 4) if it has been modied in a manner inconsistent
with the product as shipped by FIAT Products.
This warranty DOES NOT COVER any damages caused by the use of non-approved cleaners, improper installations or excessive abuse.
FIAT Products’ right to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation
including any costs of any surround material such as tile or marble.
FIAT Products is not responsible for any other incidental or consequential damages attributed to a product defect or to the repair or
exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the
exclusion or limitation of implied warranties, so this exclusion may not apply to you.)
This warranty gives you specic rights. You may have other statutory rights that may vary from state to state or province to province, in which
case this warranty does not affect such statutory rights.
In the United States:
American Standard Brands
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.americanstandard.com
In Canada:
AS Canada, ULC
5900 Avebury Rd.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: [phone]
www.americanstandard.ca
In Mexico:
American Standard B&K Mexico
S. de R.L. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Toll Free: 01-800-839-1200
www.americanstandard.com.mx
710323-100 Rev. A
THIS WARRANTY IS NOT TRANSFERABLE FROM ORIGINAL CONSUMER PURCHASER.
13-3/8"
(339 mm)
8-3/4"
(222 mm)
8-7/32"
(209 mm)
16-3/8"
(416 mm)
4X Ø 1" (25 mm)
PUNCH-OUT HOLES
SEE PUNCH-OUT HOLE DETAIL
UNDERSIDE
VIEW
2X 18°
2X 1"
(25 mm)
2X 3/16"
(4 mm)
2"
(51 mm)
2"
(51 mm)
16-7/16" (417 mm)
17-3/8" (442 mm)
21-15/16" (557 mm)
3-1/2"
(89 mm)
4"
(102 mm)
4"
(102 mm)