Instructions / Assembly

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE
WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR
THE CIRCUIT BREAKER IS SHUT OFF. GENERAL You don’t need
special tools to install this fixture. Be sure to follow the steps in the order
given. Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a ceiling
which contains a radiant type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualified
electrician. NOTE: Proper wiring is essential for the safe operation of
this fixture.
GENERAL
You don’t need special tools to install this fixture. Be sure to
follow the steps in the order given. Under no circumstances
should a fixture be hung on house electrical wires, nor should a
swag type fixture be installed on a ceiling, which contains a
radiant type heating system. Read instructions carefully. If you
are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
FIXTURE ASSEMBLY
Carefully removed the fixture from the carton and check that all
parts are included as shown in figure. Be careful not to misplace
any of the screws or parts which are needed to install this
fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP1: Secure universal mounting strap (P) on to outlet box with
box screw(O). Then install the long-threaded support rod through
the building structure. See page 2 for detailed picture for
installation.
STEP 2: Fasten the mounting frame (M) to the structure of the
building (must be fastened to the structure of the building, drywall
or plaster will not hold this fixture) with long thick wood screws (N),
not included.
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two
raised dimples on the circular strap. Wrap the ground wire from
the fixture (if supplied) around the green grounding screw, then
connect it to ground wire from the outlet box (if not fixed on the
outlet box) using a wire connector (not supplied). If ground wire
from the fixture is not supplied, wrap the ground wire (if not fixed
on the outlet box) from the outlet box around the green grounding
screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP1: Add a section of bridge wire for every 4 lamp holders，
Connect the black wire with connector ，Connect the white wire
with connector ，Complete the wiring in sequence.
STEP2: Pass the ceiling cup through the auxiliary installation wire
rope (J)Hangs tight on composite mount frame (M), Then put the
lead wires of the lamps according to the color，Connect the
black wire with connector; Connect the white wire with connector.
STEP3: After wires are connected, tuck them carefully inside
outlet box.
STEP4: Securing the Fixture ceiling pan(I) to the mounting frame
(M) with Finial(E) (F）.
CLEANING
To clean wipe fixture with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to
order replacement parts. All parts for this fixture can be ordered
from place of purchase. Be sure to use exact wording from
illustration when ordering parts.
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture.
ITEM NO: CP3627R
GROUP A: Connect to Black
House Wire
GROUP B: Connect to Whi te
House Wire
BLACK
WHITE
*PARALLEL W I R E ( round &
smooth)
*PARALLEL W I R E ( square &
ridged)
WHITE OR GREY WITH
TRACER
WHITE OR G R E Y
W I T H O U T TRACER
BROWN G O L D OR
B L A C K WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER