Installation Guide

ManualsBrandsUnbranded ManualsLED Bulbs48 in. T8 19.7-Watt Warm White (3500K) Linear LED Tube Light Bulb

9348 Mercantile Dr. - Mentor OH – 44060 - 440-255-5113 - info@uslightinggroup.com - www.uslightinggroup.com

Installation Manual

BH4-110 BH4-277 Series

BH4-110 and BH4-277 Series LED tubes are designed to replace T8 fluorescent lamps in fixtures

containing standard G13 (bi-pin) sockets. Do not attempt to install in other types of fixtures.

Part Number Matrix

Model

Length, ft

Voltage,

Volts

Color Temp,

Kelvin

Cover

BH4-110-35-C

110

3450

CLEAR

BH4-110-35-D

110

3450

DIFFUSED

BH4-110-45-C

110

4500

CLEAR

BH4-110-45-D

110

4500

DIFFUSED

BH4-110-65-C

110

6500

CLEAR

BH4-110-65-D

110

6500

DIFFUSED

BH4-277-35-C

277

3450

CLEAR

BH4-277-35-D

277

3450

DIFFUSED

BH4-277-45-C

277

4500

CLEAR

BH4-277-45-D

277

4500

DIFFUSED

BH4-277-65-C

277

6500

CLEAR

BH4-277-65-D

277

6500

DIFFUSED

Please read this manual carefully before performing an installation.

WARNING: THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF

THE PRODUCT AND THE HAZARDS INVOLVED.

IMPORTANT: The tubes have to be connected directly to 110 or 277 VAC and not to the existing ballast

in the fixture. Connecting the tubes to the fixture without bypassing the ballast will permanently damage

the tubes and the fixture.

IMPORTANT: The electrical rating of these products is 110 VAC or 240/277 VAC, the installer must

determine voltage in existing fixture prior to installation.

This Kit Includes:

 LED lamp

 Luminaire pressure sensitive label

 N label (neutral marking at lampholder terminal)

Summary of content (6 pages)

PAGE 1
9348 Mercantile Dr. - Mentor OH – 44060 - 440-255-5113 - info@uslightinggroup.com - www.uslightinggroup.com Installation Manual BH4-110 BH4-277 Series BH4-110 and BH4-277 Series LED tubes are designed to replace T8 fluorescent lamps in fixtures containing standard G13 (bi-pin) sockets. Do not attempt to install in other types of fixtures.
PAGE 2
Application     These LED tubes are suitable for installation in T8 standard luminaries. These LED tubes can’t retrofit original luminaries which use remote starter. These LED tubes are intended to retrofit maximum two lamps, UL listed surface mount, or type IC or non-IC recessed mount fluorescent luminaries with diffuser that use straight tubular lamps in luminaire of the following size (Length x Width x Height) – 120 x 60 x 8 cm. These LED tubes are intended for dry Figure 1.1 locations only.
PAGE 3
Figure 3.
PAGE 4
Figure 3.2 Double Lamp Luminaire Retrofit Before After Figure 3.
PAGE 5
Four Lamps/Double Ballast Luminaire Retrofit Before After A
PAGE 6
SAFETY NOTICE DANGER - RISK OF FIRE OR ELECTRIC SHOCK 1. WARNING – Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components. 2. WARNING – Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified technician. 3. WARNING – Risk of fire or electric shock.