Instructions / Assembly

ManualsBrandsUnbranded ManualsElectricalFull Motion TV Wall Mount with 28 in. Extension and 26 in. W Backplate by Aeon

Features:

▪ VESA Compliant: Up to 600*400mm

▪ Maximum weight capacity up to 125 lbs

▪ Lift and lock for easy installation

▪ U-cap system for clean and simple cable management

▪ +15°/-5° of easy tilt

▪ Three pivot points with up to 180° swivel

▪ Designed for 32”-60” Flat panels

▪ Horizontal movement feature allows for lateral shift

AEON-40200 AEON-40300

Installation Instructions

AEON-40200

(16” OC Studs)

AEON-40300

(24” OC Studs)

Full Motion TV Wall Mount

with Long Extending Arm

Summary of content (6 pages)

PAGE 1
AEON-40200 AEON-40300 Full Motion TV Wall Mount with Long Extending Arm AEON-40200 Features: (16” OC Studs) AEON-40300 ▪ Designed for 32”-6 0” Flat panels (24” OC Studs) ▪ VESA Compliant: Up to 600*400mm ▪ Maximum weight capacity up to 125 lbs ▪ Lift and lock for easy installation ▪ U-cap system for clean and simple cable management ▪ +15°/-5° of easy tilt ▪ Three pivot points with up to 180° swivel ▪ Horizontal movement feature allows for lateral shift Installation Instructions
PAGE 2
! WARNING PLEASE NOTE: IMPROPER INSTALLATION WILL VOID WARRANTY. Please do not begin installation until you have thoroughly read and understood these instructions. Improper installation may cause serious injury and/or damage. It is recommended that a qualified contractor install the AEON-40200 / AEON-40300 Universal Cantilever Mount. Make sure that the wall you plan to use will safely support four times the combined weight of the mounted equipment, including its accessories.
PAGE 3
Step 1 Assemble the Adaptor Plate Adaptor rail Adaptor bracket Slider Plate (M/N) Insert Slider plate(M/Nx4) into adaptor rails, then insert the adaptor bracket into adaptor rail, fix adaptor bracket and slider plate with four philips head screw M6*15mm ( C ) and four metal washers Ø 6 ( G ) using Philips headcrew driver as shown Fig.3. Philips Head Screw M6*15mm Metal Washers Ø 6 (C) Fig.
PAGE 4
Step 3 Mounting the M ount Arm Assy A. Mounting to Wood Studs 16" or 24" The AEON-40200/AEON-40300 Full Motion mount can be installed on t wo wooden studs, with center to center distances between 16"and 24". Using an electronic stud f inder (Fig.1), locate t he center of the two wooden studs at the desired mounting location. Mark the stud center positions directly on the wall.
PAGE 5
Step 4 Using Cable Management The AEON-40200 / AEON-40300 includes a cable management system where cable can be routed along the length of the arm assembly. Route the cable along the entrance of the cable management slot.(Fig.6) U-Cap Cable management Cable NOTE: For optimal performance, route the AC power cable separately form the signal cables. With all cables in place, pull the display in and out to be certain that the arm assembly moves freely, without stretching or damaging the cables. Fig.
PAGE 6
Step 6 Swivel - Adjust the flat panel display for off center viewing positions. Grasp the side edges of the display and then swivel display into its desired position (Fig.11). Fig.11 Panning - Positions the flat panel display at an angle to the wall for viewing from opposite sides of the room. Grasp the side edges of the display and then swivel and pull the display into desired position (Fig.12). Fig.12 Retracting the Flat Panel Display - Positions the display against the wall.