Installation Guide

ManualsBrandsUnbranded ManualsFlooringViena Calacata 8-Pack White 20-in x 20-in Glazed Ceramic Marble Look Floor Tile

INSTALLATION MANUAL – RECOMMENDATIONS BASED ON ISO STANDARDS

1. How to start the ideal installation of floor tiles

For optimal installation of the floor tiles some care should be taken, so this will avoid potential problems and make

service faster and better done.

1. Verify that the tiles are intended for use at the location to be installed as per specification and technical

characteristics.

2. The consumer has an obligation to read the instructions written on the packaging and ask for information before

installing the tiles. Check that the reference, caliber, shade and quality indicated on the packaging are the same.

3. For each open package, check for defective parts. Separate them for cutouts.

4. Before laying for the coating process, it is advisable to mount a panel on the floor with the tiles, using pieces of 3 or

4 boxes. This way you can see what the environment will look like after installation.

5. Plan for the best distribution of parts for ease of service, avoiding cutouts by saving time and saving materials.

6. Verify the quality of the previous jobs perfomed by the professional you hired for the installation, whether he uses

grout lines, install the tiles in good alignment and that all necessary tools he uses are in good condition.

7. Purchase 10% more products considering possible breaks, cutouts and technical reserve of products for any future

needs.

8. Prior to installation of tiles, hydraulic and electrical installations must be completed and tested.

9. Installation of tiles should be performed under appropriate weather conditions. Room temperature and materials

higher than or equal to 41ºF are recommended.

10. Check that the mortar/grout purchased are recommended for the environment and for the product to be installed

and it is advisable to consult the manufacturer in case of any doubt.

2. Mortar Preparation and Application

Mortar types

➢ ACI - Mortar with characteristics resistant to mechanical stresses typical of internal coatings, except those

applied in special areas, such as saunas, grills, greenhouses and others.

TIP: HIRE QUALIFIED LABOR

FORCE

INSTALLATION TIP: After brief inspection of the materials, wipe off any dirt and dust

that may be on the subfloor and on the back of the tiles (use a soft brush to remove dirt

and dust).

Summary of content (5 pages)

PAGE 1
INSTALLATION MANUAL – RECOMMENDATIONS BASED ON ISO STANDARDS 1. How to start the ideal installation of floor tiles For optimal installation of the floor tiles some care should be taken, so this will avoid potential problems and make service faster and better done. TIP: HIRE QUALIFIED LABOR FORCE 1. Verify that the tiles are intended for use at the location to be installed as per specification and technical characteristics. 2.
PAGE 2
➢ ACII - Suitable for outdoor use. It has properties that reduce the interference of temperature and humidity variations typical of outdoor work. RECOMMENDATION OF STICKY MORTAR TYPE Surface Area of Tile Type of flooring Ceramic tiles Environment < 400 cm² (400 < A < 900)cm² > 900cm² Indoor AC I AC lI AC lI Outdoor AC lI AC lIl AC lIl Mix only enough to be used within 30 minutes. Apply the mortar (thickness 3mm to 4mm) with the smooth side of the trowel.
PAGE 3
➢ Levellers - Large format tiles requires greater care during installation, and often take longer time from the settler due to difficulties in handling, adjust leveling on the tiles.
PAGE 4
During application, randomly remove some tiles and check that the mortar strands are being broken. Grout application The place where the grout will be applied must be clean, free of residues of dust, grease, oil or any other material that makes it difficult for the grout to adhere to the base. Note: Grout only 72 hours after installation. Spread the grout on the grout lines using a rubber spatula. Pass the spatula in the opposite direction to remove excess grout.
PAGE 5
4. Tile Protection The ceramic surface is composed of protective layer whose hardness varies according to the brightness, for example, the brighter the product, the more easily it scratches. The sand, present in all works is the number 1 enemy of the floor, so when finishing the installation and grouting, cover the floor with cardboard. 5. Post Installation Cleaning Post-work cleaning should be done with extreme care as there may be abrasive materials, paint and varnishes adhered to the surface.