普 耀 集 團 有 限 公 司 POLYSHINE HOLDINGS LTD. 東 莞 福 哥 電 子 有 限 公 司 FAVOR ELECTRONICS (DONG GUAN) CO., LTD SPECIFICATIONS (規格書) DOCUMENTCONTROLLED 編 ： F-JN10K-01-073 號 NO. 29 MAY 2008 公 司 名 稱 CO. Name ： CEI CONRAO 型 號 名 稱 Model Name ： F - J N 1 0 K - 1 B 1 0 K - 1 ( 6 0 度 中 6 度 S I L V E RP)OLYSHINE HOLDINGS LTD 普耀集團有限公司 ENG. DEPT 一 、 ELECTRICAL CHARACTERISTICS 電 氣 特 性 序號 項 目 性 能 NO.
Contact Noise 接觸雜音 (CRV) 5 6 Voltage Divider Error 分壓誤差值 Page 2 of 7 5% or less of the total resistance for over 60°(60°included) carbon film angle (Before the life test) ; 10% or less of the total resistance for 40 ° thru 60 ° carbon film angle (Before the life test) ; 15% or less of the total resistance for under 40°(40°included) carbon film angle (Before the life test) ; 碳膜角度為 60°(含)以上時,全阻值的 5%以下(壽命測試前); 碳膜角度為 40 °~60°時,全阻值的 10%以下(壽命測試前); 碳膜角度為 40°(含)以下時,全阻值的 15%以下(壽命測試前).
10% or less of over the total resistance for 60°(60°included) carbon film angle(Before the life test); 15% or less of the total resistance for 40 ° 60 ° thru carbon film angle(Before the life test); 20% or less of the total resistance for under 40°(40°included) carbon film angle(Before the life test); 碳膜角度為 60°(含)以上時,全阻值的 10%以下(壽命測試前); 碳膜角度為 40 °~60°時,全阻值的 15%以下(壽命測試前); 7 Contact resistance 接觸阻抗 (ENR) 碳膜角度為 40°(含)以下時,全阻值的 20%以下(壽命測試前).
1 Figure of lever Circular operating operation 圓形式 搖杆動作形式 2 The stopper strength of the lever 搖杆止動強度 More than 3.1Kgf 3 seconds min 大於 3.1Kgf，至少 3 秒鐘 Apply side force on the lever perpendicular to the lever’s axial direction.. 垂直於搖杆的力作用於搖杆上. 3 Pull strength of lever 搖杆拉拔強度 More than 5.0 Kgf 3 seconds min 大於 5.0Kgf，至少 3 秒鐘 Apply specified pull force on the lever upward. 作用於搖杆上，沿搖杆方向向上. 4 Push Strength of lever 搖杆推強度 More than 3.0 Kgf 3 seconds min 大於 3.
Variation of total resistance +5% should be within–30%. 2 Dry heat 耐熱性 To be operated mechanically. +5% 全阻值變化要在–30%以內， 機械方面能動作。 3 4 Cold 耐寒性 Damp heat 耐濕性 The total resistance change should be within ±20%. To be operated mechanically. 全阻值變化要在±20%以內， 機械方面能動作。 Insulation resistance: more than 10M Ω with 250V insulation resistance tester. The total resistance change should be within ±20%. To be operated mechanically. 用 250V 絕緣測試機測試，絕緣阻 抗 10MΩ以上, 全阻值變化要在±20%以內, 機械方面能動作.
Resistance to soldering heat 焊錫耐熱性 7 Number of cycles 耐久次數值 8 Variation of total resistance shall be within ± 5%, and terminals shall not work loose to injure electric contact, after test. 全阻值變化±5%以內,測試後無端 子鬆動,不會損壞電氣接點。 Total resistance≦Initial value±20%. No mechanical malfunction. 全阻值變化≦初始值±20% . 機械方面能動作. Solder dip:浸焊 Preheating condition: Surface temperature of the substrate shall be settled within 100℃ in one min. 預熱: 基板表面溫度 100℃以下，1 分鐘 內。 Solder temperature 260±5℃for 5 sec.
Less than / mΩ 低於 / mΩ Apply 2 times of the operating force of the static load on the vertical direction of the lever, measure the resistance by using the Contact Resistance Tester with 1KHZ, 20mV, 5~50mA of current. 將兩倍於作動力之靜負荷加於操作柄之 中央以(1KHZ,20mV, 5~50mA)微電流接觸 阻抗計測定. More than / MΩ / MΩ以上 A voltage of DC100V is applied between terminals. 以 DC100V 之電壓加於端子間測定. 7 Withstand voltage 耐電壓 There shall be no damage, arc or dielectric breakdown.
DOCUMENT CONTROLLED 29 MAY 2008 普耀集團有限公司 POLYSHINE HOLDINGS LTD ENG.
