sauder.com The dresser's not-so-distant cousin. 4-Drawer Chest Cannery Bridge Collection | 419068 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot # 376500 09/16/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Warranty Page 2 Not actual size Skip the power trip. This time. 27 419068 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 35AA UNIVERSAL CABINET RAIL - 8 1F HIDDEN CAM - 12 5L WARNING LABEL - 1 8F 35AC DRAWER RIGHT - 4 CAM SCREW - 12 13M WASHER - 1 10F 60M TWIST-LOCK® FASTENER - 8 SAFETY STRAP - 1 10A SLIDE CAM - 8 35AD DRAWER LEFT - 4 15F WOOD DOWEL - 2 61M SAFETY DRYWALL ANCHOR - 1 101K 1N PULL - 4 NAIL - 30 WARNING Serious or fatal crushing injuries can occur from furniture tip-over.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the ENDS (A and B) and BOTTOM (D). Do not tighten the TWIST-LOCK® FASTENERS in this step. 10F A B D 10F www.sauder.
Step 2 å Turn twelve CAM SCREWS (8F) into the FRONT LEGS (F) and DRAWER FRONTS (H). å å NOTE: The LEGS should be positioned exactly as shown. å Push twelve HIDDEN CAMS (1F) into the ENDS (A and B) and DRAWER BRACES (M67). NOTE: Be sure to use the exact holes shown in the FRONT LEGS (F). 8F (12 used) F H F H H H Arrow 1F Arrow A Hole B The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. M67 M67 M67 Arrow 1F M67 Arrow 1F Page 6 419068 www.sauder.
Step 3 å Insert two WOOD DOWELS (15F) into the holes in the FRONT LEGS (F). å Fasten the FRONT LEGS (F) to the ENDS (A and B). Tighten eight HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the FRONT LEGS insert into the holes in the ENDS. 1 2 These edges must be even. These surfaces should be even. Edge with TWIST-LOCK® FASTENERS F These edges must be even. S HI urfa DD ce EN wi CA th M S A S HI urfa DD ce EN wi CA th M S B 15F F F A These surfaces should be even. www.sauder.
Step 4 å Fasten the BACK LEGS (G) to the ENDS (A and B). Use eight BLACK 2-1/4" FLAT HEAD SCREWS (26S). Some assembly (and snacks) required. These surfaces should be even. These edges must be even. S HI urfa DD ce EN wi CA th M S A G G S HI urfa DD ce EN wi CA th M S B These surfaces should be even. 26S BLACK 2-1/4" FLAT HEAD SCREW (8 used in this step) Page 8 419068 www.sauder.
Step 5 å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the ENDS (A and B). Use sixteen GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å *patent pending glide system 1 Glide end 2 1 S HI urfa DD ce EN wi CA th M S 3 2 1 3 2 A 3 1 3 2 2 3 S HI urfa DD ce EN wi CA th M S 1 F 3 2 3 1 2 B 3 1 2 1 Glide end F 3S GOLD 5/16" FLAT HEAD SCREW (16 used in this step) www.sauder.
Step 6 å Fasten the BOTTOM (D) to the ENDS (A and B). Tighten four TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 7 å Fasten the TOP (C) to the ENDS (A and B). Tighten four TWIST-LOCK® FASTENERS. Don't worry. It isn't Rome. This can be built in a day. Long finished edge C Sur fac ew ith hol es B A www.sauder.
Step 8 å Carefully turn your unit over onto its front edges. Unfold the BACK (E) and lay it over your unit. å Make equal margins along all four edges of the BACK (E). Push on opposite corners of your unit if needed to make it "square". å Fasten the BACK (E) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. This perforation must be here. 1N NAIL (30 used in this step) E Page 12 419068 www.sauder.
Step 9 å Fasten the DRAWER FRONT MOLDING (I) to the DRAWER FRONT (H). Use three BLACK 1" PAN HEAD SCREWS (60S). å Repeat this step for the remaining DRAWER FRONTS (H). 60S BLACK 1" PAN HEAD SCREW (12 used in this step) ith w ce fa es ur v S roo g H I These edges must be even. www.sauder.
Step 10 VIEW THE T-LOCK BOX VIDEO 1 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. D982 D30 Un fi su nish rfa ed ce D30 H H D31 D31 Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove Insert the DRAWER SIDES (D30 and D31) at an angle into the slot at each end of the DRAWER FRONT (H).
Step 11 å å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D30 and D31). å å å å å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. Fasten a DRAWER RIGHT (35AC) to the RIGHT DRAWER SIDE (D30) and a DRAWER LEFT (35AD) to the LEFT DRAWER SIDE (D31). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. NOTE: The parts are marked "DRAWER RIGHT" and "DRAWER LEFT" for easy identification. NOTE: The glides are not intended to rotate.
Step 12 å å å Carefully stand your unit upright. å INSTALLATION INSTRUCTIONS: (Also available at www.yl-anchors.com) 1. Insert the SAFETY DRYWALL ANCHOR (61M) through the WASHER (13M) and one end of the SAFETY STRAP (60M). 2. Using a Phillips screwdriver or a hand drill, press the screw slightly onto the drywall. 3. Apply pressure; turn the screw until a pilot hole is made and the nylon sheath slips through. 4. Turn the screw until it is flush against the wall and you feel a firm resistance. 5.
Step 13 å To insert the drawers into your unit, tip the front of the drawers down and drop the glides on the drawers behind the glides on the unit. Lift the front of the drawers up and slide them into the unit. å Apply the WARNING LABEL (5L) to the upper LEFT DRAWER SIDE (D31). You should be able to read the label when the drawer is open. When the drawer is closed, it will hide the label. Peel off the backing and apply the label as shown in the diagram.
Step 14 å To make adjustments to the drawers, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
419068 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (10F) dans les gros trous des EXTRÉMITÉS (A et B) et le DESSOUS (D). ÉTAPE 2 Fixer le DESSOUS (D) aux EXTRÉMITÉS (A et B).
ÉTAPE 11 ÉTAPE 13 Insérer une EXCENTRIQUE DE COULISSE (10A) dans les CÔTÉS DE TIROIR (D30 et D31). Pour insérer le tiroir dans l’unité, incliner le devant du tiroir vers le bas et faire tomber les coulisses du tiroir derrière les coulisses de l’unité. Relever le devant du tiroir et l'enfiler dans l'élément. Fixer un TIROIR DROIT (35AC) sur le CÔTÉ DROIT DE TIROIR (D30) et un TIROIR GAUCHE (35AD) sur le CÔTÉ GAUCHE DE TIROIR (D31).
419068 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los SUJETADORES TWIST-LOCK® en este paso. Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (10F) dentro de los agujeros grandes de los EXTREMOS (A y B) y del FONDO (D). Fije el FONDO (D) a los EXTREMOS (A y B). Apriete cuatro SUJETADORES TWIST-LOCK®.
PASO 11 PASO 13 Inserte un EXCÉNTRICO DE CORREDERA (10A) en los LADOS DE CAJÓN (D30 y D31). Para insertar el cajón en el unidad, incline la parte delantera del cajón hacia abajo y deje que los corrimientos del cajón caigan detrás de los corrimientos de la unidad. Levante la parte delantera del cajón y deslícelo dentro de la unidad. Fije un CAJÓN DERECHO (35AC) al LADO DERECHO DE CAJÓN (D30) y un CAJÓN IZQUIERDO (35AD) al LADO IZQUIERDO DE CAJÓN (D31).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
