sauder.com Sweet stand. Sweet dreams. Night Stand Harbor View Collection | 401328 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot # 373129 05/21/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Warranty Page 2 Not actual size Skip the power trip. This time. 27 401328 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Insert a CONNECTOR SCREW (NN) into each HIDDEN CONNECTOR (X). X NN Step 2 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Use your hammer to tap four HIDDEN CONNECTORS (X) with SCREWS into the BRACE (E). X E X www.sauder.
Step 3 å Push seven HIDDEN CAMS (1F) into the BOTTOM (D), BRACE (E), and DRAWER BRACE (M67). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. 2F Arrow Arrow 1F (7 used) 1F 2F M67 D Arrow E Arrow 1F 2F Insert the metal end of the CAM DOWEL into the HIDDEN CAM. Page 6 401328 www.sauder.
Step 4 å Fasten the CABINET RIGHT (40CA) and CABINET LEFT (40CB) to the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD SCREWS (LL) through holes #1 and #3. å Fasten four ANGLE BRACKETS (AA) to the ENDS (A and B). Use four BLACK 9/16" LARGE HEADS SCREWS (KK). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the ENDS. Remember: Righty tighty. Lefty loosey.
Step 5 å Fasten the SKIRT (M57) to the BOTTOM MOLDING (K). Use two BLACK 1-7/8" FLAT HEAD SCREWS (GG). å Fasten the BOTTOM MOLDING (K) to the BOTTOM (D). Use four BLACK 1-1/4" FLAT HEAD SCREWS (II). GG BLACK 1-7/8" FLAT HEAD SCREW (2 used for the SKIRT) Rounded edge K Un su finis rfa he ce d Finished surface M57 D Sur HIDface w DEN ith CA MS II BLACK 1-1/4" FLAT HEAD SCREW (4 used for the BOTTOM MOLDING) Page 8 401328 www.sauder.
Step 6 å Fasten the ENDS (A and B) to the BOTTOM (D). Tighten four HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Finished edge Finished edge B K D Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.sauder.
Step 7 å Tap two MOLDING CONNECTORS (DD) into the notches in the MOLDINGS (N, O, and P). å Fasten the MOLDINGS (N, O, and P) to the ENDS (A and B). Use four BLACK 2-1/4" FLAT HEAD SCREWS (FF). Use your hammer to tap the MOLDING CONNECTORS (DD) into the notches in the MOLDINGS. Flat end DD Flat end DD P O N Finished surface N P B O A FF BLACK 2-1/4" FLAT HEAD SCREW (4 used in this step) Page 10 401328 www.sauder.
Step 8 å Fasten the TOP (C) to the MOLDINGS (N, O, and P). Use seven BLACK 1-5/8" PAN HEAD SCREWS (HH). å NOTE: Do not overtighten the SCREWS into the TOP. HH BLACK 1-5/8" PAN HEAD SCREW (7 used in this step) Long rounded edge Do not overtighten the SCREWS (HH). N C P Un su finis rfa he ce d O www.sauder.
Step 9 å Fasten the BRACE (E) to the ENDS (A and B). Tighten four HIDDEN CONNECTORS (X). å Fasten the BRACE MOLDING (L) to the BRACE (E). Tighten two HIDDEN CAMS. How to use the HIDDEN CONNECTOR To fasten two parts together using the HIDDEN CONNECTORS, insert your screwdriver, at an angle, into the slot in the HIDDEN CONNECTOR. While pushing the screw into the hole of the adjoining part, turn the screwdriver clockwise to tighten. L The HIDDEN CAMS must be here.
Step 10 å Fasten the END MOLDINGS (Q) to the ENDS (A and B). Use four BLACK 9/16" LARGE HEAD SCREWS (KK) through the ANGLE BRACKETS on the ENDS and into the grooves in the END MOLDINGS. å Turn two FOOT SCREWS (W) a few turns into the two holes in the BOTTOM MOLDING (K). å Next, turn a FOOT (V) onto each FOOT SCREW (W). Turn the FEET clockwise until the FEET and FOOT SCREWS are tight against the BOTTOM MOLDING (K). Don't worry. It isn't Rome. This can be built in a day.
Step 11 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square". å Fasten the BACK (F) to your unit using the NAILS (MM). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. MM NAIL (20 used in this step) ed ish fin Un ce rfa su F Page 14 401328 www.sauder.
Step 12 VIEW THE T-SLOT DRAWER VIDEO å Pull the DRAWER FRONT BRACKETS (BB) apart and slide them into the grooves in the DRAWER SIDES (D44 and D45). You may need to gently tap them in with a hammer. å NOTE: The DRAWER FRONT BRACKETS are marked "RH" and "LH" for easy identification. å Fasten the DRAWER FRONT (G2) to the DRAWER FRONT BRACKETS (BB). Use four BLACK 9/16" LARGE HEAD SCREWS (KK). å Slide the DRAWER BOTTOM (D723) into the grooves in the DRAWER SIDES (D44 and D45) and DRAWER FRONT (G2).
Step 13 å å VIEW THE T-SLOT DRAWER VIDEO Fasten the DRAWER BRACE (M67) to the DRAWER FRONT (G2). Tighten one HIDDEN CAM. Fasten the DRAWER BACK (D115) to the DRAWER SIDES (D44 and D45) and DRAWER BRACE (M67). Use five BLACK 1-9/16" FLAT HEAD SCREWS (30S). 1 Maximum 210 degrees Arrow M67 Minimum 190 degrees G2 Start each screw a few turns before completely tightening any of them. 30S 2 BLACK 1-9/16" FLAT HEAD SCREW (5 used in this step) Be sure the DRAWER BOTTOM inserts into the DRAWER BACK groove.
Step 14 å Fasten the DRAWER RIGHT (40CC) and DRAWER LEFT (40CD) to the DRAWER SIDES (D44 and D45). Use four GOLD 5/16" FLAT HEAD SCREWS (LL) through holes #2 and #4. å Fasten the KNOB (EE) to the DRAWER FRONT (G2). Use a SILVER 1-1/4" PAN HEAD SCREW (JJ). Roller end JJ SILVER 1-1/4" PAN HEAD SCREW (1 used for the KNOB) 1 2 4 D45 3 Roller end D44 G2 EE 1 2 3 4 LL GOLD 5/16" FLAT HEAD SCREW (4 used for the SLIDES) www.sauder.
Step 15 å å Carefully stand your unit upright. å To make adjustments to the drawer, loosen the SCREWS in the DRAWER FRONT BRACKETS, make needed adjustments, and tighten the SCREWS. å NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
401328 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Insérer une VIS DE CONNECTEUR (NN) dans chaque CONNECTEUR ESCAMOTABLE (X). Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. ÉTAPE 2 Fixer les EXTRÉMITÉS (A et B) au DESSOUS (D). Serrer quatre EXCENTRIQUES ESCAMOTABLES. À l'aide de un marteau, enfoncer quatre CONNECTEURS ESCAMOTABLES (X) avec VIS dans l'ENTRETOISE (E). Attention: Risque des dégâts ou blessures.
ÉTAPE 10 ÉTAPE 13 Fixer les MOULURES D'EXTRÉMITÉ (Q) aux EXTRÉMITÉS (A et B). Utiliser quatre VIS TÊTE LARGE 14 mm NOIRES (KK) à travers les CONSOLES À ÉQUERRE situées sur les EXTRÉMITÉS, et dans les rainures des MOULURES D'EXTRÉMITÉ. Fixer l’ENTRETOISE DE TIROIR (M67) au DEVANT DE TIROIR (G2). Serrer un EXCENTRIQUE ESCAMOTABLE. Faire tourner deux VIS DE PIED (W) de quelques tours dans les deux trous de la MOULURE DE DESSOUS (K).
401328 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 Inserte un TORNILLO CONECTOR (NN) dentro de cada CONECTOR INVISIBLE (X). Ligeramente clave dos CONECTORES DE MOLDURA (DD) dentro de las muescas de las MOLDURAS (N, O y P). PASO 2 Fije las MOLDURAS (N, O y P) a los EXTREMOS (A y B). Utilice cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 57 mm (FF). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso.
PASO 11 PASO 14 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Fije el CAJÓN DERECHO (40CC) y el CAJÓN IZQUIERDO (40CD) a los LADOS DE CAJÓN (D44 y D45). Utilice cuatro tornillos DORADOS de cabeza PERDIDA de 8 mm (LL) a través de los agujeros No. 2 y No. 4. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (F) y colóquelo sobre la unidad.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers and shelves. • Risk of injury. • Never exceed the weight limits shown in • Top-heavy furniture can tip over. the instructions. • Overloaded drawers or shelves can break. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • El sobrecargo de cajones y estantes. • Un riesgo de lesiones. • La caída de mobiliario inestable. • La rotura de cajones sobrecargados. • Nunca exceda los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
