sauder.com Don't get caught with your pants on the ground. 5-Drawer Chest Harbor View Collection | Model 401323 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 2-3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 6-24 Hammer Français 25-28 Español 29-32 Safety 33-34 Warranty Not actual size Skip the power trip. This time. 35 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification U C D24 T D170 V D945 D25 L2 M67 F2 E Q A3 D30 D171 F2 D945 B3 D31 G2 M67 F2 D D R M57 D30 D171 BB D945 BB D31 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 35AA UNIVERSAL CABINET RAIL - 10 1F HIDDEN CAM - 11 60M SAFETY STRAP - 1 35AC DRAWER RIGHT - 5 2F 61M CAM DOWEL - 11 SAFETY DRYWALL ANCHOR - 1 35AD DRAWER LEFT - 5 13M WASHER - 1 CC FOOT SCREW - 2 Locate this nylon SAFETY STRAP (60M) to be used later in assembly. Do not accidentally throw away.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. NN BLACK 2-1/4" FLAT HEAD SCREW - 4 OO BLACK 1-7/8" FLAT HEAD SCREW - 2 PP BLACK 1-5/8" PAN HEAD SCREW - 7 QQ BLACK 1-1/4" FLAT HEAD SCREW - 10 RR BLACK 1-1/8" PAN HEAD SCREW - 4 TT VV BLACK 9/16" LARGE HEAD SCREW - 1 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (DD) into the large holes in the BRACES (D and E). å Insert four METAL PINS (HH) into the small holes in the short edges of the LOWER BRACES (D). Scan this QR code or go to this address: http://qr.sauder.
Step 2 å Push eleven HIDDEN CAMS (1F) into the BACKS (F2) and DRAWER BRACES (M67). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. 2F Arrow (11 used) 1F F2 F2 F2 M67 Arrow M67 M67 M67 M67 Insert the metal end of the CAM DOWEL into the HIDDEN CAM. www.sauder.
Step 3 å å VIEW THE DRAWER GLIDE VIDEO Fasten the UNIVERSAL CABINET RAILS* (35AA) to the ENDS (A3 and B3). Use twenty GOLD 5/16" FLAT HEAD SCREWS (TT) through holes #1 and #3. Remember: Righty tighty. Lefty loosey. *patent pending glide system TT GOLD 5/16" FLAT HEAD SCREW (20 used in this step) Glide end 1 2 1 3 2 1 3 Finished edge 2 3 1 3 A3 2 3 1 2 1 3 2 2 3 1 3 2 3 1 B3 2 3 1 2 1 Glide end Finished edge Page 8 401323 www.sauder.
Step 4 å Fasten the UPPER BRACE (E) to the UPPER BRACE MOLDING (Q). Tighten three TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 5 å Tap two MOLDING CONNECTORS (GG) into the notches in the MOLDINGS (T, U, and V). Use your hammer to tap the MOLDING CONNECTORS (GG) into the notches in the MOLDINGS. Flat end Flat end GG GG V U T Page 10 401323 www.sauder.
Step 6 å Fasten the LEFT END (B3) to the LEFT MOLDING (V). Use two BLACK 2-1/4" FLAT HEAD SCREWS (NN). NN BLACK 2-1/4" FLAT HEAD SCREW (2 used in this step) V Finished edge B3 www.sauder.
Step 7 å Insert six METAL PINS (HH) into the holes in the short edges of the BACKS (F2). å Fasten the BACKS (F2) to the LEFT END (B3). Tighten three HIDDEN CAMS. å NOTE: Be sure the METAL PINS in the BACKS insert into the holes in the LEFT END. B3 F2 th S wi AM ce C rfa EN Su IDD H F2 th S wi AM ce C rfa EN Su IDD H F2 th S wi AM ce C rfa EN Su IDD H (6 used) HH Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened.
Step 8 å First, fasten the BOTTOM MOLDING (R) to the SKIRT (M57). Use two BLACK 1-7/8" FLAT HEAD SCREWS (OO). å Then, fasten one of the LOWER BRACES (D) to the BOTTOM MOLDING (R). Use four BLACK 1-1/8" PAN HEAD SCREWS (RR). å NOTE: You should start each SCREW a few turns before completely tightening any of them.
Step 9 å Fasten the LOWER BRACES (D) to the LEFT END (B3). Tighten two TWIST-LOCK® FASTENERS. å NOTE: Be sure the METAL PINS in the edges of the LOWER BRACES insert into the holes in the LEFT END. å NOTE: Do not put any pressure on the LOWER BRACES (D) until they are fastened to the RIGHT END in the next step. Don't worry. It isn't Rome. This can be built in a day. B3 R D D Surface and edge with TWIST-LOCK® FASTENERS Surface and edge with TWIST-LOCK® FASTENERS Page 14 401323 www.sauder.
Step 10 å Fasten the RIGHT END (A3) to the RIGHT MOLDING (U). Use two BLACK 2-1/4" FLAT HEAD SCREWS (NN). å Fasten the RIGHT END (A3) to the BACKS (F2). Tighten three HIDDEN CAMS. å NOTE: Be sure the METAL PINS in the edges of the backs insert into the holes in the RIGHT END. å Fasten the LOWER BRACES (D) to the RIGHT END (A3). Tighten two TWIST-LOCK® FASTENERS. å NOTE: Be sure the METAL PINS in the edges of the LOWER BRACES insert into the holes in the RIGHT END.
Step 11 å Fasten the TOP (C) to the MOLDINGS (T, U, and V). Use seven BLACK 1-5/8" PAN HEAD SCREWS (PP). å NOTE: You should start each SCREW a few turns before completely tightening any of them. Do not overtighten the SCREWS. Rounded edge PP BLACK 1-5/8" PAN HEAD SCREW (7 used in this step) T V C Su witrface hh ole s U Page 16 401323 www.sauder.
Step 12 å Insert the dowel end of four TWIST-LOCK® FASTENERS (DD) into the ENDS (A3 and B3). Follow the enlarged diagram. å NOTE: If you already pushed TWIST-LOCK® FASTENERS into the UPPER BRACE (E), pull the FASTENERS back out of the holes. å Push the UPPER BRACE (E) onto the TWIST-LOCK® FASTENERS in the ENDS (A3 and B3). å Fasten the UPPER BRACE (E) to the ENDS (A3 and B3). Tighten four TWIST-LOCK® FASTENERS. Push the UPPER BRACE (E) onto the TWIST-LOCK® FASTENERS. DD Q B3 E DD E B3 A3 www.
Step 13 å Carefully turn two FOOT SCREWS (CC) a few turns into the BOTTOM MOLDING (R). å Next, turn a FOOT (BB) onto the other end of each FOOT SCREW (CC). Turn the FEET clockwise until the FOOT SCREWS are tight in the BOTTOM MOLDING and FEET. å NOTE: Do not overtighten the FOOT SCREWS. CC BB R BB Page 18 401323 www.sauder.
Step 14 VIEW THE T-LOCK BOX VIDEO 1 2 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D24 D945 D24 D25 L2 L2 Groove å D25 Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Insert the SMALL DRAWER SIDES (D24 and D25) at an angle into the slot at each end of the SMALL DRAWER FRONT (L2).
Step 15 VIEW THE DRAWER GLIDE VIDEO å å Insert a SLIDE CAM (MM) into the SMALL DRAWER SIDES (D24 and D25). å å å å NOTE: The glides are not intended to rotate. Fasten a DRAWER RIGHT (35AC) to the SMALL DRAWER RIGHT SIDE (D24) and a DRAWER LEFT (35AD) to the SMALL DRAWER LEFT SIDE (D25). Use four GOLD 5/16" FLAT HEAD SCREWS (TT) through holes #1 and #2. NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. Fasten two KNOBS (EE) to the SMALL DRAWER FRONT (L2).
Step 16 å Carefully stand your unit upright and position the unit in its final location. We recommend using the SAFETY STRAP (60M) for added stability. å NOTE: Do not turn the SAFETY DRYWALL ANCHOR (61M) into a wall stud. If you prefer to fasten the SAFETY STRAP (60M) to a wall stud, go to your local hardware store for proper hardware. å INSTALLATION INSTRUCTIONS: (Also available at www.yl-anchors.com) 1.
Step 17 å å To insert the drawers into your unit, tip the front of the drawer down and drop the glides on the drawer behind the glides on the unit. Lift the front of the drawer up and slide it into the unit. Almost time to celebrate! With a nap. NOTE: Be sure the drawer with the LARGE BOTTOM DRAWER FRONT (H2) is inserted at the bottom of the unit. L2 G2 Place the glide on the SLIDE behind the glide on the RAIL. G2 G2 H2 Page 22 401323 www.sauder.
Step 18 å Apply the WARNING LABEL (XX) to the SMALL DRAWER LEFT SIDE (D25). You should be able to read the label when the drawer is open. When the drawer is closed, it will hide the label. Peel off the backing and apply the label as shown in the diagram. WARNING Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over: -Place heaviest items in the lowest drawers. -Unless specifically designed to accommodate, do not set TVs or other heavy objects on top of this product.
Step 19 å To make adjustments to the drawers, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
Modèle 401323 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Enfoncer deux CONNECTEURS DE MOULURE (GG) dans les crans des MOULURES (T, U et V). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (DD) dans les gros trous des ENTRETOISES (D et E). Insérer quatre GOUPILLES EN MÉTAL (HH) dans les petits trous dans les chants courts des ENTRETOISES INFÉRIEURES (D).
ÉTAPE 9 ÉTAPE 12 Fixer les ENTRETOISES INFÉRIEURES (D) à l'EXTRÉMITÉ GAUCHE (B3). Serrer deux FIXATIONS TWIST-LOCK®. Insérer l'extrémité filetée des quatre FIXATIONS TWIST-LOCK® (DD) dans l'EXTRÉMITÉS (A3 et B3). Suivre les indications du schéma agrandi. REMARQUE : S'assurer de bien insérer les GOUPILLES EN MÉTAL situées sur les chants des ENTRETOISES INFÉRIEURES dans l'EXTRÉMITÉ GAUCHE.
ÉTAPE 15 ÉTAPE 17 Insérer une EXCENTRIQUE DE COULISSE (MM) dans les CÔTÉS DE PETIT TIROIR (D24 et D25). Pour insérer les tiroirs dans l'élément, abaisser le devant du tiroir et faire passer les coulisses situées sur le tiroir derrière les coulisses situées sur l'élément. Relever le devant du tiroir et l'enfiler dans l'élément. Fixer un TIROIR DROIT (35AC) sur le CÔTÉ DROIT DE PETIT TIROIR (D24) et un TIROIR GAUCHE (35AD) sur le CÔTÉ GAUCHE DE PETIT TIROIR (D25).
Modelo 401323 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los SUJETADORES TWIST-LOCK® en este paso. Ligeramente clave dos CONECTORES DE MOLDURA (GG) dentro de las muescas de las MOLDURAS (T, U y V). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (DD) dentro de los agujeros grandes de las RIOSTRAS (D y E).
PASO 9 PASO 12 Fije las RIOSTRAS INFERIORES (D) al EXTREMO IZQUIERDO (B3). Apriete dos SUJETADORES TWIST-LOCK®. Inserte el extremo con cabilla de cuatro SUJETADORES TWIST-LOCK® (DD) dentro de los EXTREMOS (A3 y B3). Siga el diagrama ampliado. NOTA: Asegúrese de insertar las ESPIGAS DE METAL sujetadas en los bordes de las RIOSTRAS INFERIORES en los agujeros del EXTREMO IZQUIERDO. NOTA: No use ninguna presión sobre las RIOSTRAS INFERIORES (D) hasta que se fijen al EXTREMO DERECHO en el próximo paso.
PASO 15 PASO 17 Inserte un EXCÉNTRICO DE CORREDERA (MM) dentro de los LADOS DE CAJÓN PEQUEÑO (D24 y D25). Para insertar los cajones dentro de la unidad, incline la parte delantera del cajón y deje que los corrimientos del cajón caigan detrás de los corrimientos de la unidad. Levante la parte delantera del cajón y deslícelo dentro de la unidad. Fije un CAJÓN DERECHO (35AC) al LADO DERECHO DE CAJÓN PEQUEÑO (D24) y un CAJÓN IZQUIERDO (35AD) al LADO IZQUIERDO DE CAJÓN PEQUEÑO (D25).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
