Installation Guide

ManualsBrandsUnbranded ManualsDog Carriers4 ft. x 4 ft. x 6 ft. Welded Wire Kennel

Page 1 of 801/31/2020

PREMIUM KENNEL

308606B: 4' x 8' x 6'

308606B and 308605B USER MANUAL

Assembly - No Tools Necessary

Please read the instructions completely before beginning construction of the kennel.

1. Open the box and conﬁrm that all parts are included.

WARNING: CONTAINS LEAD. May be harmful if eaten or chewed. May generate dust containing lead. Wash hands after use. Keep out of

reach of children. WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Parts Image Description

308605B

Quantity

308606B

Quantity

Kennel Panels 7 11

Kennel Gate Panel 1 1

Panel Clamps 16 24

Gate Latch 1 1

3 Way Center Pole Clamps 2 2

4 Way Center Pole Clamp N/A 1

Bungee Cords 10 14

Center Pole 1 2

Roof Frame 2 3

Waterproof Roof Cover 1 1

Panel Caps 16 25

This product should not be used with aggressive dogs, or pets that are escape artists.

Not all pets can be trained for containment. Please discuss with your veterinarian or

certiﬁed trainer to determine if this product is appropriate for your pet.

Midwest Air Technologies Inc. cannot guarantee that this product will, in all cases, keep

a pet within the established boundary. If you have reason to believe that your pet may

pose a danger to others or harm itself (through chewing on the product or otherwise) if it

is not willing to remain conﬁned in this product, you should not rely solely on this product

to contain your pet. Midwest Air Technologies Inc. shall not be liable for any property

damage, economic loss, or any consequential damages sustained as a result of the

animal exiting the system.

308605B: 4' x 4' x 6'

Summary of content (8 pages)

PAGE 1
PREMIUM KENNEL 308606B and 308605B USER MANUAL 308606B: 4' x 8' x 6' 308605B: 4' x 4' x 6' This product should not be used with aggressive dogs, or pets that are escape artists. Not all pets can be trained for containment. Please discuss with your veterinarian or certified trainer to determine if this product is appropriate for your pet. Midwest Air Technologies Inc. cannot guarantee that this product will, in all cases, keep a pet within the established boundary.
PAGE 2
Assembly (Continued) 2. Select the location for your kennel. 3. Lay out the panels (A & B) to allow for ease of installation. Use the image (FIG. 1) as a guide. FIG. 1 (A) (A) (A) (A) (A) (A) (A) 308606B Top View (A) (A) (B) (A) (A) (A) 308605B Top View (A) (A) (A) (A) (B) (A) (A) 4. To start, form a corner by standing up two panels (A). Ensure that these form a 90° angle (FIG. 2). FIG. 2 90º NOTE: Side panels are to be positioned on the INSIDE EDGE of the front and back panels (FIG.
PAGE 3
Assembly (Continued) 5. Install two panel clamps (C). NOTE: The wing nuts used on the panel clamps should face toward the OUTSIDE of the kennel, not the INSIDE (FIG. 4). 6. One panel clamp should be located approximately 6" from the top, the other 6" from the bottom (FIG. 5). Do not overtighten the panel clamp wing nuts and bolts until all panels are installed. This will allow for minor adjustments before finalizing and tightening the panel clamps. 7.
PAGE 4
Installing the Roof Cover (J) 1. Starting at the back of the kennel, install the roof framework (I) into the top of the panel. Repeat for the front (FIG. 7). 2. Attach the center pole (H) to the roof framework (I) using the roof panel clamps (E). 308605B uses only one center pole. 308606B uses two center poles, connected by the 4 way center pole clamp (F) NOTE: The wing nuts should face the INSIDE of the kennel to prevent damage to the roof cover when installed (FIG. 8).
PAGE 5
PERRERA DE PRIMERA CALIDAD 308606B y 308605B MANUAL DEL USUARIO 308606B (1,2 m ancho x 2,4 m prof x 1,8 m alto) 308605B (1,2 m ancho x 1,2 m prof x 1,8 m alto) Este producto no debe usarse con perros agresivos ni con mascotas que tengan facilidad para escaparse. No todas las mascotas pueden entrenarse para permanecer encerradas. Hable con su veterinario o entrenador certificado para determinar si este producto es apropiado para su mascota. Midwest Air Technologies Inc.
PAGE 6
Montaje (a continuación) 2. Seleccione la ubicación de la perrera. 3. Disponga los paneles (A & B) de manera que sean fáciles de instalar. Utilice la imagen como guía (FIG. 1). FIG. 1 (A) (A) (A) (A) (A) (A) (B) (A) 308605B (A) (A) (A) (A) 308606B Vista Superior Vista Superior (A) (A) (A) (A) (A) (A) (B) (A) 4. Para comenzar, forme una esquina levantando dos paneles (A). Asegúrese de que éstos formen un ángulo de 90° (FIG. 2). FIG.
PAGE 7
Montaje (a continuación) 5. Instale dos abrazaderas para panel (C). NOTA: Las tuercas de mariposa usadas en las abrazaderas para panel deben estar dirigidas hacia el EXTERIOR de la perrera, no hacia el INTERIOR (FIG. 4). 6. Debe colocar una abrazadera para panel a 15 cm aproximadamente de la parte superior y la otra a 15 cm de la parte inferior (FIG. 5). No apriete demasiado las tuercas de mari posa y los pernos de la abrazadera para pan el, hasta que todos los paneles estén instalados.
PAGE 8
Instalación de la cubierta de techo (J) 1. Comenzando por la parte trasera de la perrera, instale la estructura del techo (I) en la parte superior del panel. Repita para el frente (FIG. 7). 2. Fije el poste central (H) a la estructura del techo (I), utilizando las abrazaderas para los paneles de techo (E). 308605B utiliza sólo un poste central. 308606B utiliza dos postes centrales, conectados por la abrazadera de 4 vías para el poste central.