Instructions / Assembly

ManualsBrandsUnbranded ManualsDog Carriers6 ft. x 10 ft. x 6 ft. Replacement Galvanized Metal Gate Latch for Chain Link Kennel

Page 1 of 807/01/20

CHAIN LINK KENNEL

6' x 10' x 6' (1.8m x 3m x 1.8m)

308595PE USER MANUAL

WARNING: CONTAINS LEAD. May be harmful if eaten or chewed. May generate dust containing lead. Wash hands after use. Keep out of

reach of children. WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Assembly - Tools Required: Phillips Screwdriver, Pliers and Gloves

Please read the instructions completely before beginning construction of the kennel. Choose a ﬂat

surface to assemble the kennel. For easiest installation and best results, it is recommended that two

people work together to assemble this kennel.

Parts Image Description Quantity

A Door (Assemble First, See Page 2) 1

B Middle Posts 2

C Corner Posts 4

D Tension Rods - Long Round (72") 2

E Pole Caps 7

F Top & Bottom Railings - Side Long (67”) 4

G Gate Clips 20

H Door Latch 1

I Top & Bottom Railings - End Short (59”) 8

J Chain Link Mesh 1

Metal Tie Wires 64

Customer Service: 800-628-8815

This product should not be used with aggressive dogs, or pets that are escape artists.

Not all pets can be trained for containment. Please discuss with your veterinarian or certiﬁed trainer to

determine if this product is appropriate for your pet. Pets may escape or become trapped in loose chain link fabric.

Check the fabric and ties regularly to ensure a secure ﬁt is maintained.

Midwest Air Technologies, Inc. cannot guarantee that this product will, in all cases, keep a pet within the established boundary. If you have

reason to believe that your pet may pose a danger to others or harm itself (through chewing on the product or otherwise) if it is not willing

to remain conﬁned in this product, you should not rely solely on this product to contain your pet. Midwest Air Technologies, Inc. shall not

be liable for any property damage, economic loss, or any consequential damages sustained as a result of the animal exiting the system.

Summary of content (8 pages)

PAGE 1
6' x 10' x 6' (1.8m x 3m x 1.8m) CHAIN LINK KENNEL 308595PE USER MANUAL This product should not be used with aggressive dogs, or pets that are escape artists. Not all pets can be trained for containment. Please discuss with your veterinarian or certified trainer to determine if this product is appropriate for your pet. Pets may escape or become trapped in loose chain link fabric. Check the fabric and ties regularly to ensure a secure fit is maintained. Midwest Air Technologies, Inc.
PAGE 2
Assembling the Door NOTE: Assemble the door with the parts laying flat on the ground. (A5) (A4) (K) (K) (A3) FIG. 1 (A6) (A1) (A2) (G) (G) FIG. 2 (A3) FIG. 3 Parts Image Description (K) Quantity A1 Door Frame - Fixed Side (65") 1 A2 Door Frame - Latch Side (66.75") 1 A3 A4 A5 A6 Upper & Lower Door Frame Bars Chain Link Mesh - Small Tension Rods - Short Round (62") Outer Door Frame - Latch Side (72") 2 1 2 1 G Gate Clips 10 K Metal Tie Wires 4 1.
PAGE 3
Assembling Kennel Framework FIG. 4 NOTE: Illustration below shows kennel assembled. FIG. 5 FIG. 6 Inside View (I) (F) (I) (F) (C) (C) (C) (D) (J) (B) (I) (F) (I) (I) (F) (I) FIG. 7 Receiver Tube 1. With the door frame laid down, slide top and bottom end rails (F) through the receiver tubes of the assembled door (A) (FIG. 7). Do not tighten set screws yet, they will need to be loose in a later step to adjust the door. 2.
PAGE 4
Chain Link Mesh Installation 1. Chain link mesh (J) is rolled tightly for shipping. Check the top and bottom for any pickets that may have come unhooked from each other. They may need to be twisted back into place (FIG. 6). It is recommended to unfold the mesh onto a flat surface. 2. The chain link mesh should be attached to the OUTSIDE of the kennel frame. You can start installation of the mesh on either side of the door.
PAGE 5
6' x 10' x 6' (1.8m x 3m x 1.8m) PERRERA DE MALLA DE ALAMBRE 308595PE MANUAL DEL USUARIO Este producto no debe usarse con perros agresivos ni con mascotas que tengan facilidad para escaparse. No todas las mascotas pueden entrenarse para permanecer encerradas. Hable con su veterinario o entrenador certificado para determinar si este producto es apropiado para su mascota. Las mascotas pueden escaparse o quedar atrapadas en la malla de alambre holgada.
PAGE 6
Ensamblaje de la puerta NOTA: Ensamble la puerta con las piezas extendidas en el suelo. (A5) (K) (A4) (K) (A3) FIG. 1 (A6) (A1) (A2) (G) (G) FIG. 2 (A3) FIG. 3 Piezas 1. Imagen Descripción (K) Cantidad A1 Marco de puerta - lado fijo (65 pulg.) 1 A2 Marco de puerta - lado del cerrojo (66.75 pulg.) 1 A3 Largueros superior e inferior del marco de la puerta 2 A4 Malla de alambre - pequeña 1 A5 Varillas tensoras - cortas redondas (62 pulg.
PAGE 7
Ensamblaje de la estructura de la perrera FIG. 4 NOTA: La siguiente ilustración muestra la perrera totalmente ensamblada. FIG. 5 FIG. 6 Vista interior (I) (F) (I) (F) (C) (C) (C) (J) (D) (B) (I) (F) (I) (I) (F) (I) FIG. 7 1. Tubo receptor Con el marco de la puerta extendido en el suelo, deslice los largueros cortos superior e inferior (F) en los tubos receptores de la puerta ensamblada (A) (FIG. 7).
PAGE 8
Instalación de la malla de alambre 1. La malla de alambre (J) se enrolla muy apretada para su embarque. Revise los bordes superior e inferior para detectar uniones que puedan haberse separado. Es posible que tenga que volver a unirlas (FIG. 6). Es recomendable desenrollar la malla en una superficie plana. 2. La malla de alambre debe fijarse al EXTERIOR de la estructura de la perrera. Puede iniciar la instalación de la malla en cualquier lado de la puerta.