User manual

1. Use as directed:
This product serves exclusively lighting purposes and may:
only be operated using a suitable transformer, output: 12V.
not be exposed to strong mechanical loads or to strong contamination.
only be installed and operated after a condition inspection if the product
is dirty or has been moistened through storage.
not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2. Technical Data:
Operating voltage: 12V
Safety class: III
Safety type: IP 67
Bulb: QR-CBC51, max. 35W
Dimensions: Ø: 15cm, H: 21cm
Recess dimensions: Ø: 13cm, H: 13,5cm
Rotary- /Swivel range: 350°/ 85°
Weight: 0,85 kg
Importeur: SLV Elektronik GmbH
IP 67: Protection against dust(dust-tight) - Protection against the
penetration of water when temporarily submerged.
3. Installation
The complete installation must be done by an electrical expert,
who is familiar with the valid directives.
Attention: Switch off power of the mains supply or respectively of
the connection lead before doing any works.
Use only parts, which are supplied with the product or are described as
accessories! Otherwise the product or the installation might not be
sufficiently safe!
Indication for the installer: In case you do not install a completely
supplied system (with transformer), you are considered a "manufacturer" by
the low-voltage directive. In this case you are required to ensure the
conformity of the whole system and declare it by attaching the CE-sign.
Installation place:
The product is suited for recessed floor installation.
Make sure that the product is mounted on a stable, even and tilt-fixed
background. The light exit should be placed at least so far from the
illuminated surface, as indicated as minimum distance on the type plate of
the luminaire:
. Pay special caution to easily inflammable
objects (e.g. foliage).
Use as power lead only a suitable earth cable. Do not use PVC cables!
Preparing the low-voltage(12 V) power supply
The transformer should be used up to 80 % of its capacity. The total watt
power of the connected light fittings must not exceed the power output of
the transformer. The distance between spot and transformer should be at
least 20 cm. The conductor length between a electronical transformer and a
lamp may not be longer than 2 metres (Electromagnetic Emission). Note
the manufacturers information for the transformer.
High currents with low-voltage installations! Use only heat resistant
wires and clamps to avoid danger of fire. Check all electrical connections
once in a while for a secure fit.
Before installation
ATTENTION: DO NOT REMOVE THE GREASE ON THE SCREWS
AND THE SCREW HOLES!
The grease inhibits anodic corrosion(electrolysis). Renew the grease on
the screw connections after each time the fixture has been opened.
Carry out the installation when the weather is dry.
Prepare the recess if not done yet. When installing the lighting unit
outdoors provide a gravel bed, 20 cm thick, beneath the installation pot.
This serves as protection from corrosion.
Prepare the power supply lead according to valid rules for outdoor
installations.
Separate Installation Steps
Remove the shield by loosening the screws.
Take the fixture out of the plastic casing.
Remove the metal plate inside.
Direct the earth cable, in sufficient length, through the cable screwing.
If through-wiring is desired use the second cable screwing.
Connect the product with the prepared low-voltage power supply.
Secure the cable screwing.
Inserting the bulb: Remove the front cover. Carefully remove the
protection glas and the gasket. Insert the bulb into the socket.
Adjust the light exit to the desired position. Secure the fixing screw (A).
Assemble the fixture in reverse order.
Pay attention that all gaskets fit properly.
The product is now ready for operation.
4. Operation:
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention: Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not cover the product (Remove leaves and dirt once in a while).
Do not fasten anything on the product.
Replace damaged protection glasses immediately!
After each opening of the product the gasket should be checked and
cleaned. The bearing surface of the gasket must be free of dirt. These
measures ensure that the IP class is maintained.
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
ATTENTION! The following enviromental influences may have
unwanted effects on the surface of the product:
acid rain and sour soil high salt content in the air
thawing salt cleaning agents
other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface. Cleaning tip: Switch off power! Painted surfaces: Use a damp
cloth. Stainless steel: Use a special cleaning agent.
What is to do if a bulb is defect or does not work?
Disconnect the product from power, before you exchange the bulbs.
Caution: Let the bulb cool down first before replacement – otherwise
considerable risk of injury exists because of the hot surface.
Replace the bulbs only with bulbs of the same data like socket, power
and capacity. Every other sort of bulb can lead to damages of the light.
Replacing the bulb: see Installation.
5. What else has to be considered?
Disconnect the product from power, before you…
clean or maintain the product.
do any works on the product or its components (electric expert).
228360 05/2008 © by SLV Elektronik GmbH
Technical Details are subject to change. Duplication prohibited !
ENGLISH
Instruction Manual
for recessed fitting
GIMBLE OUT 90
Please read carefully and keep for further reference !
20cm
A