Installation Guide

Step 2:
OPTION A: Prepare existing countertop
1. Make sure existing countertop cut-out opening is the proper size. Set the new
sink into opening. The sink rim should rest evenly on the countertop. Slight
DGMXVWPHQWVFDQEHPDGHXVLQJDßOHRUDMLJVDZ
 8VHFDXWLRQWRDYRLGFKLSSLQJRUFUDFNLQJWKHFRXQWHUWRSZKLOHßOLQJRU
sawing.
 $IWHUßQDOßWWLQJUHPRYHWKHQHZVLQNIURPFXWRXW
OPTION B: Prepare a new countertop using the sink as
a template
1. Carefully place the sink upside down on the
countertop at the desired position. Trace the outline
of the sink onto the countertop. Do not cut along
this line.
2. Draw a line 3/8” (9mm) inside the sink outline.
Measure the cut-out line you just drew and
compare to all sink dimensions. The cut-out should
be approximately 3/4” (19mm) smaller than the
overall sink dimensions.
3. Verify both measurements.
4. Drill a pilot hole inside the cutting line.
 8VLQJDMLJVDZFXWDORQJWKHLQVLGHOLQHWRFUHDWH
the opening in the countertop.
OPTION C: Prepare a new countertop using the cut-out template provided
1. A template is provided to use in cutting the sink hole. Template can be located either:
a. On the outside of the sink carton. Use scissors
to cut along dotted line. Measure the cut-out
line and compare to all sink dimensions.
b. Inside carton. Measure the cut-out line and
compare to all sink dimensions. The cut-out
line should be 3/4” smaller than the overall
sink dimensions.
2. Place template on countertop. Trace completely
around the edge of the template directly onto your
countertop.
3. Drill a pilot hole inside the cutting line.
 8VLQJDMLJVDZFXWDORQJWKHLQVLGHOLQHWRFUHDWH
the opening in the countertop.
Step 3: Apply the mounting clips
 7XUQVLQNXSVLGHGRZQRQWRDFOHDQVRIWVXUIDFH
2. Six clips are recommended for installation. If
UHTXLUHGWZRH[WUDFOLSVDUHLQFOXGHG
3. Attach clips over the pre-drilled mounting slot in the
sink rim (see diagram for placement). Ensure clip
jaws are facing the outside edge of sink.
4. Verify clip snaps are fully seated into the mounting slot.
5. Turn all clip jaws parallel to the sink rim.
www.FrankeUSA.com
Length
Width
Step 2
Cut along dotted line of
template pattern found
on sink packaging.
1
Countertop
Trace completely around
edge of cut-out template
Using a 2" hole saw, drill
a hole on the inside of the
line that was traced using
the cut-out template.
Countertop
Countertop
Using a jigsaw, cut along outline
traced on countertop.
3
4
2
OPTION C: 1
2
43
Countertop
Using a 2" hole saw, drill
a hole on the inside of the
line that was traced using
the cut-out template.
Countertop
Using a jigsaw, cut along outline
traced on countertop.
1
4
5
2
OPTION B: 1
4
2
5
Countertop
Sink
Integrated
installation
rail
Front rim
Clip
Clip
Clip
Clip
Clip
Clip
Step 3: 1-4 5