Specification
SPEC-DATA
ª
and MANU-SPEC
ª
are registered trademarks of Reed Elsevier Inc. The ten part SPEC-DATA format conforms to the editorial style
of The Construction Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ©2007 Reed Construction Dataª. All Rights Reserved.
grade bituminous resins modified with synthet-
ic resins. This SBS modified, rubberized asphalt
is then reinforced with a strong, inert rein-
forcement to withstand puncture and severe
stress. The reinforcement is sandwiched
between 2 layers of rubberized asphalt, mak-
ing the membrane tacky on both sides, which
means the membrane bonds cleanly to the
primed surface and to itself on overlap areas.
A release film is laid on the top of the mem-
brane to keep the material from adhering to
itself prior to application.
COMPATIBILITY
Jiffy Seal is compatible with asphalts and most
urethanes. If there are any questions about
product compatibility, contact a Protecto
Wrap representative before applying Jiffy
Seal in such applications.
ACCESSORY MATERIALS
JS160H Mastic and Protecto Wrap primers are
specially formulated for use with Jiffy Seal
membranes. A good drainage design at or
near the footings, along with a drainage mat,
will ensure a sound waterproof system.
No. 100 Primer is a high-tack SBS rubber
base primer. It is used on all vertical surfaces
before application of the membrane and on
all surfaces with temperatures between 25
and 40 degrees F (-4 and 4 degrees C).
No. 100 VOC Primer is a VOC compliant ver-
sion of Protecto Wrap’s standard No. 100
Primer.
No. 80 Primer is an asphalt based primer
suitable for use on all horizontal applications
above 40 degrees F (-7 degrees C).
No. 80 VOC Primer
is a VOC compliant ver-
sion of Protecto Wrap’s standard No. 80 Primer.
No. 80 Green Concrete Primer is for use on
green concrete surfaces.
No. JS160H Mastic is a rubberized blend of
bituminous and synthetic resins used for seal-
ing detail cuts and membrane terminations.
No. 6000 Water-Based Primer is a water-
based primer that contains no VOCs. The No.
6000 Primer comes in a 1 gallon concentrate.
Mix the concentrate at a ratio of 1 part water
to 1 part concentrate for a vertical applica-
tion (or as needed for jobsite conditions). For
horizontal applications, mix 2 parts water to 1
part concentrate.
LIMITATIONS
• Jiffy Seal is not recommended for applica-
tion where the membrane will be exposed
to continuous sunlight
• Do not apply primer or membrane to wet,
SHEET WATERPROOFING 07 13 00
Protecto Wrap Co.
®
TABLE 1 PRODUCT PACKAGING (JIFFY SEAL)
Jiffy Seal 140/60 Jiffy Seal 400 Jiffy Seal 500
Length, ft (m) 50 (15.2) 50 (15.2) 50 (15.2)
Width, in (mm)
1
12, 30, 60 (305, 762, 1524) 30, 60 (762, 1524) 6, 12 (152, 305)
Rolls/carton 4, 1, 1 1 8, 4
Weight/carton, lb (kg) 60, 84, 120 (27, 38, 54) 68, 138 (31, 63) 75 (34)
Coverage, ft
2
(m
2
) 50, 125, 250 (4.6, 11.6, 23) 125, 250 (11.6, 23) 25, 50 (2.3, 4.6)
1
Special widths are available upon request.
TABLE 2 PRODUCT PACKAGING (PRIMER AND MASTIC)
No. 100 Primer No. 80 Primer JS160H Mastic
36 10.5 oz tubes, lb (kg) - - 41 (18.6)
1 gallon can, lb (kg) 38 (17.2) 38 (17.2) 55 (25)
5 gallon pail, lb (kg) 46 (21) 46 (21) 68 (31)
55 gallon drum, lb (kg) 485 (220) 485 (220) -
TABLE 3 TYPICAL PHYSICAL PROPERTIES (JIFFY SEAL)
Jiffy Seal 140/60 Jiffy Seal 400 Jiffy Seal 500
Thickness, mil ± (mm) 60 (1.5) 70 (1.8) 60 (1.5)
Tensile strength,
425 425 -
membrane
Tensile strength of polyester
reinforcement only 3200 3200 -
(ASTM D412), psi (kPa) min
Elongation (ASTM D412), % 500 500 1500
Permeance (ASTM E96B), max 0.003 0.002 0.003
Puncture resistance
(ASTM E154), lb (N)
80 (356) 80 (356) -
Pliability (ASTM D146) Passes Passes Passes
Tensile strength
(ASTM D412), psi (MPa)
600 (4.1) min 500 (3.5) min -
Color Black Black Black
Water absorption 0.23 0.23 0.23
Exposure to fungi in soil for
Unaffected Unaffected Unaffected
16 weeks (GSA-PBS 07115)
Resistance to hydrostatic
150 150 150
head (feet of water)
1
1
Hydrostatic head tests are performed by applying membrane on primed concrete, then sealing the
waterproofed concrete to a pressure chamber. Water is introduced to 150 head feet.