Specification

ManualsBrandsUnbranded ManualsBuilding materials1/2 ft. x 50 ft. Jiffy Seal

1. Product Name

Jiffy Seal Waterproofing Membranes

• Jiffy Seal 140/60

• Jiffy Seal 140/60 CW (Cold Weather)

• Jiffy Seal 140/60 AK (Alaska)

• Jiffy Seal 400

• Jiffy Seal 500

Primers

• Jiffy Seal No. 100 Primer

• Jiffy Seal No. 100 VOC Primer

• Jiffy Seal No. 80 Primer

• Jiffy Seal No. 80 VOC Primer

• Jiffy Seal No. 80 Green Concrete Primer

• Jiffy Seal No. 6000 Water-Based Primer

• Jiffy Seal No. JS160H Mastic

2. Manufacturer

Protecto Wrap Co.

1955 South Cherokee St.

Denver, CO 80223

(800) 759-9727

(303) 777-3001

Fax: (303) 777-9273

E-mail: info@protectowrap.com

www.protectowrap.com

3. Product Description

BASIC USE

The Jiffy Seal waterproofing membrane system

is designed for use on concrete, masonry,

metal and wood structures as positive protec-

tion against water, salts and certain acids and

alkalis. Areas of application include foundation

walls, split slabs, tunnels, plaza decks, parking

decks, balconies, spandrels, earth shelters,

bridge decks, planters, shower pans, beneath

stucco and in mechanical rooms.

• Jiffy Seal 140/60 is recommended for appli-

cation at air and surface temperatures of

40 degrees F (4 degrees C) or above

• Jiffy Seal 140/60 CW is recommended for

application at temperatures from 25 - 75

degrees F (-4 degrees - 24 degrees C). When

temperatures fall below 40 degrees F

(4 degrees C), overlaps must be lightly primed

• Jiffy Seal 140/60 AK can be applied at temper-

atures as low as 25 degrees F (-4 degrees C)

without priming overlap areas. For these types

of cold temperature installations, the mem-

branes must be stored in a heated area above

60 degrees F (16 degrees C) for a minimum of 2

hours prior to application. Remove only the

material that can be readily installed within 1

hour. When temperatures range between 25

and 40 degrees F (-4 and 4 degrees C), any

material left in the cold for more than an hour

must be primed at overlaps

• Jiffy Seal 400 is a 70 mil (1.8 mm) heavy duty

waterproofing membrane for application

on bridge decks and parking structures

where extra strength may be required.

Asphaltic concrete can be applied directly

against the membrane for a positive bond

immediately after the protective polyethyl-

ene film has been removed. Jiffy Seal is not

intended as a wearing surface and must

be covered after application

• Jiffy Seal 500 is a 60 mil (1.5 mm) unrein-

forced conformable sheet used for detail-

ing around protrusions, drains, footings and

uniform surfaces

BENEFITS

• Jiffy Seal is environmentally safe and meets

NIOSH/OSHA manufacturers standards and

regulations

• Jiffy Seal is reinforced and provides superi-

or puncture resistance and strength over

other sheet membranes

• Jiffy Seal membranes are inert, inorganic

and will never rot, decay or be affected by

bacteria/fungus

• According to service needs, either Jiffy Seal

140/60, Jiffy Seal CW, Jiffy Seal AK or Jiffy

Seal 400 may be used

• When properly applied, Jiffy Seal systems pro-

vide protection for the life of the structure

•

Jiffy Seal requires no curing period. It can be

applied over a wide temperature range

and then can be immediately overlaid or

backfilled

• Jiffy Seal gives the design professional the

advantage of a strong reinforced water-

proofing membrane that can be applied

down to 25 degrees F (-4 degrees C)

• A unique “Zip Strip” in the polyethylene

release film along both edges of the roll pro-

vides both a built-in overlap seam guide and

a self-adhering overlap, eliminating the need

for a joint seal tape or compound process

• There is no paper backing to remove during

installation

• Jiffy Seal products are totally cold-applied

over a wide temperature range

• Molecular bonding of seams forms Jiffy

Seal into a monolithic membrane over or

around the entire surface being water-

proofed

• Protecto Wrap’s high-quality control guar-

antees a uniform thickness over the entire

project

PACKAGING

See Tables 1 and 2.

COMPOSITION & MATERIALS

Jiffy Seal preformed membranes are manu-

factured from a formulation of premium

SHEET WATERPROOFING 07 13 00

Protecto Wrap Co.

SPEC-DATA

and MANU-SPEC

are registered trademarks of Reed Elsevier Inc. The ten part SPEC-DATA format conforms to the editorial style

Vertical foundation application details

Summary of content (6 pages)

PAGE 1
SHEET WATERPROOFING 07 13 00 ® Protecto Wrap Co. 1. Product Name Jiffy Seal Waterproofing Membranes • Jiffy Seal 140/60 • Jiffy Seal 140/60 CW (Cold Weather) • Jiffy Seal 140/60 AK (Alaska) • Jiffy Seal 400 • Jiffy Seal 500 Primers • Jiffy Seal No. 100 Primer • Jiffy Seal No. 100 VOC Primer • Jiffy Seal No. 80 Primer • Jiffy Seal No. 80 VOC Primer • Jiffy Seal No. 80 Green Concrete Primer • Jiffy Seal No. 6000 Water-Based Primer • Jiffy Seal No. JS160H Mastic 2. Manufacturer Protecto Wrap Co.
PAGE 2
SHEET WATERPROOFING ® grade bituminous resins modified with synthetic resins. This SBS modified, rubberized asphalt is then reinforced with a strong, inert reinforcement to withstand puncture and severe stress. The reinforcement is sandwiched between 2 layers of rubberized asphalt, making the membrane tacky on both sides, which means the membrane bonds cleanly to the primed surface and to itself on overlap areas.
PAGE 3
SHEET WATERPROOFING ® damp, frosty or contaminated surfaces • Do not apply primer or membrane to frozen concrete • Jiffy Seal is not recommended as a pond or tank liner except for “between slab” applications • Do not apply over sealants containing tar. If bitumen modified materials are encountered, consult a Protecto Wrap representative for guidance • Jiffy Seal is not designed for use as a finished traffic system • For green concrete, use Jiffy Seal No.
PAGE 4
SHEET WATERPROOFING ® Co. for detail recommendations. All outside corners must be double-covered to a minimum of 6" (152 mm) on each side of the axis of the corners. Apply a 12" (305 mm) wide strip of membrane; then cover it with a full width sheet or overlap the full width a minimum of 6" (152 mm) from the axis on both sides of the corner. Cant strips of epoxy mortar, latex modified cement mortar or urethane sealants should be used on inside horizontal corners. Do not use JS160H Mastic as a fillet.
PAGE 5
SHEET WATERPROOFING ® when application is interrupted by change in construction scheduling. Drainage Boards and Footing Drains Use Protecto Drain 2000V on vertical walls and Protecto Drain 2000H on horizontal surfaces. Waterstops, footing drains and most drainage boards are compatible and may be used in conjunction with Jiffy Seal waterproofing membranes. Consult Protecto Wrap for compatible drainage systems. Block Walls For block wall waterproofing, apply a heavy coat of Jiffy Seal No.
PAGE 6
SHEET WATERPROOFING ® adequate ventilation. Refer to MSDS for additional information and warnings 6. Availability & Cost AVAILABILITY Jiffy Seal is manufactured in Denver, CO, and is available worldwide through a network of Protecto Wrap distributors. For detailed product information or to find a local representative or distributor, contact the Protecto Wrap Co. COST Jiffy Seal waterproofing membranes are competitively priced. Contact a local representative or the corporate office for information. 7.