Data Sheet

2
Rev. 2/22
* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.
Actual products offered for sale may vary in use, design, required attachments and safety features. See distributor for details on all warranties.
Reelmaster
®
5410-D Specifications
*
The Reelmaster 5410 is manufactured
in Tomah, WI ISO 9002 Certified Plant.
REELMASTER 5410-D TIER 4 DIESEL, MODEL 03606
ENGINE
Yanmar® 3-cylinder, liquid cooled, diesel engine. 36.8 hp (27.5 kW), 74.4 ft. lbs. (105 Nm) torque, 1.64 liter displacement.
LUBRICATION
Pressurized lubrication system with 5.0 quart (4.7 liter) capacity.
FUEL FILTER
Replaceable spin-on fuel filter/water separator.
AIR CLEANER
Heavy-duty three-stage, radial seal air cleaner with restriction indicator.
COOLING
Plate and bar radiator/oil cooler combination, 6.3 fins per inch, 10 quart (9.5 liter) capacity.
FUEL TANK CAPACITY
14 gallon (53 liter) capacity.
HYDRAULIC OIL CAPACITY
15 gallon (56.8 liter) capacity.
TRACTION DRIVE
Front drive wheels powered by a hydrostatic pump with individual wheel motors. All-wheel drive optional with CrossTrax® All-Wheel Drive system, which transfers
power from the front wheels to the opposite rear wheels via independent rear wheel motors
GROUND SPEED
0-10 mph (0-16 km/hr) forward transport; 0-8 mph (0-12.8 km/hr) mow; 0-4 mph (0-6.4 km/h) reverse.
TIRES
Front traction tires: 26.5 x 14-12 turf tires Rear steer tires: 20 x 12-10
MAIN FRAME
High strength steel frame with welded construction.
BRAKES
Individual left and right drum-type front wheel brakes. Brakes may be actuated for service braking via left foot pedal. Integrated foot pedal lock provides parking
brake. Dynamic braking through hydrostatic traction drive system.
STEERING
Rear wheel, power steering with an independent hydraulic pump and circuit.
GAUGES
InfoCenter
TM
onboard LCD display shows gauges, alerts/faults, service reminders, electrical system diagnostics, indicates fuel level, coolant temp., low oil pressure,
alternator, engine hours, engine rpm, voltage, reel speed, backlap speed, glow indicator (diesel), lift/lower indicator.
CONTROLS
Single foot-operated traction pedal, foot actuated mow speed limiter, foot actuated service and parking brake. Hand-operated key ignition switch, throttle,
isochronous engine speed control, cutting unit raise/lower joystick, cutting unit engage switch, and headlight switch all positioned on right hand pivoting control
console.
ELECTRICAL & INTERLOCKS
Heavy-duty 12-volt battery, 570 CCA, 55 amp alternator. Electronic control unit is a microprocessor based, solid state control unit with diagnostic capabilities.
Traction pedal, parking brake, operator presence in seat, and cutting unit engage/disengage safety interlock switches.
REEL DRIVE
Reel drive circuit is split independently for front and rear cutting units. Hydraulic functions controlled by an integrated hydraulic control block. Reel speeds are
electronically adjustable in nine incremental settings. Standard on-board backlapping.
CUTTING UNIT LIFT/LOWER
Front and rear cutting unit lift/lower is sequenced for uniform starting and ending points.
SEAT
Deluxe high back suspension seat with fore, aft, height and weight adjustment.
ROPS
Standard with seat belt
HEIGHT
63" (160 cm) seat top, 85" (217.2 cm) top of ROPS.
LENGTH (2WD)
111" (281.9 cm)
WHEEL BASE
60" (152.4 cm)
OPERATIONAL WIDTH
113.5" (288.3 cm)
TRANSPORT WIDTH
92" (233.7 cm)
WEIGHT
2,943 lbs. (1,335 kg) (2WD), 3,053 lbs. (1,385 kg) (4WD)
CERTIFICATION
Complies with ANSI B71.4-2004 and CE requirements. Certain machine configurations require rear weight kits for standards compliance, see Operator’s Manual for details.
WARRANTY
Two-year limited warranty. Refer to the Operator’s Manual for further details.