Installation Guide

ManualsBrandsUnbranded ManualsBathroom Sink Faucets10-B42WPNCH

Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-319-3757,

7 a.m. - 5 p.m., CST, Monday - Friday.

NON-METALLIC

LAVATORY FAUCET

Español p. 4

12-04-2017

www.homewerksww.com

PACKAGE AND HARDWARE CONTENTS

PREPARATION

PART DESCRIPTION QUANTITY

A Faucet 1

B Mounting nut 2

SAFETY INFORMATION

Please read and understand this entire manual before

attempting to assemble, operate or install the product.

CAUTION

• Cover the sink drain to avoid losing parts.

WARNING

• It is recommended that protective eyewear be worn

during installation.

Before beginning assembly of product, make sure all parts

are present. Compare parts with package contents list and

hardware contents. If any part is missing or damaged, do

not attempt to assemble the product. Contact customer

service for replacement parts.

Estimated Assembly Time: 30 minutes

Tools Required for Assembly (not included): Adjustable

Wrench, Groove Joint Pliers, Pipe Wrench, Phillips

Screwdriver, and Supply Lines, Silicone Caulk

Installations may vary depending on how the previous faucet

was installed. Supplies necessary for the installation of the

faucet are not all included; however, they are available

wherever plumbing supplies are sold.

Prior to beginning installation, turn off the hot or cold water

lines, then turn on the old faucet to release built-up pressure.

When installing the new faucet, hand tighten the connector

nuts. DO NOT OVERTIGHTEN. Connections that are too

tight will reduce the integrity of the system.

ITEM #0935182

MODEL #EL-4224

#10-B42-WPN-CH

NSF-61

Summary of content (6 pages)

PAGE 1
NON-METALLIC LAVATORY FAUCET ITEM #0935182 MODEL #EL-4224 Español p. 4 NSF-61 PACKAGE AND HARDWARE CONTENTS PART DESCRIPTION QUANTITY A Faucet 1 B Mounting nut 2 A B SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. CAUTION • Cover the sink drain to avoid losing parts. WARNING • It is recommended that protective eyewear be worn during installation.
PAGE 2
PRODUCT SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS Max. flow rate: 1.2 GPM (4.542 LPM) at 60 PSI Washerless cartridges ASME A112.18.1/CSA B125 Manufactured to include no more than 0.25% weighted average lead content on wetted surfaces NSF 61-9 Chrome finish ASSEMBLY INSTRUCTIONS 1. Turn off water at the supply valve under the sink or at the main water supply, disconnect the supply line, and remove old faucet. Clean and dry surface area where new faucet will be mounted. 4.
PAGE 3
TROUBLESHOOTING PROBLEM: Leaks underneath handle. POSSIBLE CAUSE: Bonnet has come loose or O-ring on cartridge is dirty or twisted. CORRECTIVE ACTION: 1. Move the handle to the off position. Unscrew the handle screw and remove the handle. 2. Tighten the bonnet by turning it clockwise. Move the cartridge stem to the on position. The leak should stop draining out from around the cartridge stem. 3. If the leak does not stop, shut off the water supply. Remove the bonnet by turning it counter-clockwise.
PAGE 4
NO-METALICO GRIFO LAVATORIO ARTÍCULO #0935182 MODELO #EL-4224 NSF-61 CONTENIDO DEL PAQUETE PIEZA DESCRIPCIÓN CANTIDAD A Grifo 1 B Tuerca de montaje 2 A A B INFORMACIÓN DE SEGURIDAD Lea y comprenda completamente este manual antes de intentar ensamblar, usar o instalar el producto. PRECAUCIÓN •Cubra el desagüe para evitar que se pierdan piezas. ADVERTENCIA • Se recomienda usar gafas protectoras durante la instalación.
PAGE 5
ESPECIFICACIONES DEL PRODUCTO ESPECIFICACIONES ESPECIFICACIONES Caudal de flujo máximo: 4,542 LPM (1,2 GPM) a 60 PSI Cumple con la norma ASME A112.18.1/CSA B125 Fabricado para que no incluya más de 0,25% de contenido promedio en peso de plomo para superficies con agua Cumple con la norma NSF 61-9 Peso total del artículo: 0,85 kg Cartucho sin arandela INSTRUCCIONES DE ENSAMBLAJE 1.
PAGE 6
SOLUCIÓN DE PROBLEMAS PROBLEMA: Hay goteras debajo de la manija. CAUSA POSIBLE: El bonete está flojo o la junta tórica del cartucho está sucia o torcida. ACCIÓN CORRECTIVA: 1. Mueva la manija a la posición de apagado. Desatornille el tornillo de la manija y retire la manija. 2. Apriete el bonete girándolo en dirección de las manecillas del reloj. Coloque el vástago del cartucho en la posición de encendido. La fuga debe dejar de drenar alrededor del vástago del cartucho. 3.