+ Do not use a power drill for installation. «Install and test the lock with the door open to avoid being locked out. + Please read all the instructions before contacting customer support. + Please contact customer support before returning the product to the store.
Interior Exterior Interior Assembly Assembly Assembly Mounting Plate Strike Bolt Backup Key i Fa Screw D Screw E AA Alkaline Batteries Screw F May hotshot included i for some regions Screwdriver User Guide Drill Template Be — Reset Needle
Installation Video Please scan this QR code to watch the easy step by step installation video before attempting to install Ultra log U-Bolt WiFi. Or you can also view the website directly. 1. Preparing Door Check the door’s dimensions. Step? Measure to confirm that the door is between mm-45 mm) thick. Step Measure to confirm that the diameter of the hole Step 3 Measure to confirm that the backseat is either moor 70mm). Steps Measure to confirm that the diameter of the hole in the door edgewise* (25 mm).
2. Installing Bolt and Strike Step? Install Bolt into the door. Make sure the UP 4 icon goes up. Note: Bolt is sat for 2% backs st initially. It can bie adjusted to 2%” if needed. MONTHS To adjust It please make sure the bolts retracted, then, press i, twist and pollinator pus hit to your desired length. Step 2 Install Strike into the door frame.
3. Installing Exterior Assembly Step? Keep Bolt foretasted and the cylinder tailpiece futurism. Install Exterior Assembly. Please siz suasion insert the mechanical kay during installation. Step 2 Align its two sticks with two holes on Bolt. The cable goes through the hole baffle Bolt. 4. Installing Interior Assembly Mounting Plate Step 1 Route the cable through the hale on Interior Assembly Mounting Plate. Step Secure Interior Assembly Mounting Plate to Exterior Assembly using Screws D.
MONTHS 5. Installing Interior Assembly Step? Remove the battery cover of the Interior Assembly. Step 2 Insert the connector of the cable to the socket on Interior Assembly. Press the connector in firmly until iris completed seated.
Step 3 Rotate the knob and keep tin a warts position to stay unlocked. Step 4 Attach Interior Assembly to Mounting Plate and tighten 2 Screws E. 6. Installing the Batteries and Performing the Door Handing Process This step will teach your lock the orientation of your door and is crucial to lock operation.
Step 1 Rotate the knob and keep tin a horizontal position to stay locked. MONTHS Step Insert 4 AA Alkaline Batteries. Nita: Ann fingerprint core san unlock U-Bolt Fro WIFE in Factory Default Mode. Step 3 Install battery cover. 7. Installing the Door Sensor(Optional) The door sensor lets you know whether the door is open or closed through the App. When tha auto lock is enabled in the App, your Ultra log will only lock itself when the door is closed.
Option 1 Installing with Sticker Peel off either side of the sticker and push it against the door frame about 10s. Peel off the other side and secure the door sensor on the sticker firmly. Put on the door sensor cover at last. Option 2 Installing with Screw F Push the door sensor against the wall and secure it with Screw F. You may need to drill a hole first if the door frame is hard to screw in with Screw F directly. Put on the door sensor cover at last.
User Guide Video Please watch our easy step by step User Guide video before attempting to use your Ultra log U-Bolt WiFi Smart Lock. SIMON Or you can also view the website directly. 1. Product Overview Backup Kay Hole Used to enter the code and unlock from outside. Backup Key Hole Used to insert the key to unlock in emergency situations. Ultralight Button Used to lock from the outside, illuminate the keypad for code entry and confirm previous operation etc.
1.2 Interior oI — o Battery TE Compartments Led Indicator LID] = Rests Button Reset Button Used to reset the lock to Factory Default settings. Battery Compartments Used to insert 4 A fillings batteries. Note: Lithium batteries may have a longer life, but when they begin to ail, they fail quickly. We don't recommend them because they don't give you a lot of time to change: your batteries before the lock is completely dead. Please don't usa any Rechargeable Battery.
MONTHS Step? Scan above QR code to download the App, or search App Store (10S) and Google Play (Android). Step Pantheon App, register U-etc account and log in the account. Step 3 Make sure the lock is irs Factory Daft Mode. Turn on Bluetooth on your smartphone, stay near the lack (within 10 feet And search the lock in the App. Step a Pair the lock in the App and start to use it. DON'T WANT TO USE THE APP? Please go to page 14 for programming guide for Standalone Mode.
3. Using Your Lock 3.1 Unlock From Outside «User Code Enter 4-8 digit code and press Ultra log Button to unlock. Nita: You can press Guttural Button to turn on Kay pad back light. » Smartphone Use your smartphone to unlock. Please refer to tha guide in U-tac App. 3.2 Lock From Outside Press Ultra log Button to lock manually. Enable Auto Lock feature and the lock will re lock automatically. 3.3 Unlock From Inside Rotate the knob ta a vertical position to unlock.
3.4 Reset tha Lock Please note all data will be erased if you reset U-Bolt WiFi to factory default. If you are using U-etc App as Owner, please click “Delete and Reset" to remove the lock from your U-etc Account, then use a Reset Deadline to push tha Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps. 3.5 Replace Batteries Please use 4 high-quality alkaline AA batteries for replacement. when the battery is dead. MONTHS 3.
4. Standalone Mode Programming Guide Iris recommended to use U-etc App to program your lock. If you don't have a smartphone or don’t want to use the App, you can usa tha programming instructions below. warning Striations Mode is NOT available after the locks registered in App! Please reset the lock to Factory Default Mode first to program your lock in Standalone Mode. 4.1 Add Admin Code in Standalone Mode Admin Code must be created first prior to any other programming. Only ona Admin Code is available.
1 beep with green light, then steady blue light 2 beeps with green light All lights off SRG E] 4.3 Delete Admin and User Pleas taser the lock to Factory Default Soda to delete Admin and all Users. How to resat the lock in Standalone Mode? Pleas use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps. 1. How to reset U-Bolt WiFi? Please note all data will be erased if you reset U-Bolt WiFi to factory default.
2. What if 1 lost the paired smartphone? Please go to or login U-etc App via another smartphone to change your U-etc Account password. 3. How can | unlock U-Bolt WiFi if battery runs out? There will be low battery alert on the lock and App when battery is low. Red LED will flash 3 times along with 3 beeps when the lock is activated. Please replace batteries. If battery runs aut, you can use the backup key to unlock. 4.
+ No usas un taladro electrónica para Instalación. + Instala prueba la cerradura con puerta abierta para evitar ser bloqueada. «Por favor lee todas las instrucciones antes de contactar al apoyo de clientes. + Por favor contacta al apoyo de clientes antes de devolver sl producto ala tienda.
Ideo de Instalación olvide de instalación de paso a paso antes de intentar instalar Ultraligero U-Volt 5 8 Por favor escanea este GR código para ver x 5 Jifia 1. Preparando la puerta Chequea las dimensiones de la puerta. Paso? Mide para confirmar que el espesor de la puerta es entre 1 T4735 mm-45 mm). Paso 2 Mide para confirmar que el diámetro de agujero es 2" (53 mm). Paso 3 Mide para confirma que el baceta de la puerta tiene un espesor de 2%" or2% (80 mma 70mm).
3. Instalación de ensamble Externo Paso? Nanten el Cerrojo atraicionar y la cola del cilindro pasterizad. Instala Ensamble Externo. fue fistulo ste instales la lave mecanicé. Paso 2 Alinea sus dos barras con dos orificios en el Cerrojo. El cable pasa por al orificio gafare del Cerrajeo. EE 4.
S. Instalacién de Ensamble interno Paso? Remueve la tapa de baterías de Ensamble Intimo. Pago 2 Inserta el conector del caballa enchufe en ensamble interno. Presiona firmemente hasta que sea completamente asentado.
Paso 2 Inserta 4 AA Baterías Alcalinas. bajo ios predeterminad de frica, Paso 3 Instalación de baterías. 7. Instalación del sensor de puerta (opcional) El sensor de la puerta le permite saber isla puerta esté abierta cerrada a través de la aplicación. Cuando el bloqueo automático esté habilitado en la aplicación, su Ultraligero solo se bloquear cuando la puerta esté cerrada.
Opción 1 Instalación con adhesiva Despegue cada lado de la pegatina y empújela contra el marco de la puerta unos 10 segundos. Despegue el otro lado y asegure firmemente el sensor de la puerta en la etiqueta. Ponga la tapa del sanso de puerta. = Oxidan 2 Instalación con tornillo F Empuje el sensor de la puerta contra la pared y reelegirlo con el Tomillar F. Es posible que deba perforar un agujero primero sil marco de la puerta es difícil de atornillar directamente con el Tomillo F.
1.2 Interior U Tapa de Baterías TT] = Compartimientos [E de Baterías Indicador LED m of Peris J = J Boten de Respete Boten de Respete Se usa para secretear |a cerradura a ajustes predeterminados de fabrica. Compartimientos de Materias Se usa para insertar 4 batanaras salinas Ad. Nota: Las baterías delirio pueden tener una vida més larga, pera cuando comienzan a agotar, agotan rápidamente.
2. Configuración de Cerradura Escanear el código GR para descargar la APP Paso? Escanea sobre el código QR para descargar la App, © busca “U-etc” an App Resistor) y Golee Palisandro. Paso 2 Abre la App, registra cuenta de U-teca ingresa con la cuenta. Paso 3 Aseglarare de que la cerradura esté en defino predeterminada de Fabrica. Enciende Bluetooth en tu celular inteligente, quédate cerca de la contraproducente 1.5 pies) y busca la cerradura en la App.
3.4 Respete dela Cerradura Por favor date cuenta da que todos los datos se bar si secreteas U-Volt Jifia a ajuste predeterminado. Si estés usando U-etc App como Duenario, por favor haz clic™Eliminar y Resetear™ para remover la cerradura desde tu cuenta U-etc, luego usa una llave para secretear a pulsar el botan de representen la parte inferior de Ensamble Intimo) para acerca de 3 segundos hasta que se oyen un largo pitido y dos cortos, 3.
1 pitido con luz verde, luego luz azul estables pitidos con luz verde Apagan todas luces 4.3 Eliminar Aminad y Usuario Por favor secretea la cerradura a Modo predeterminado de tabica para eliminar Aminad y todos los usuarios. céntimo recatean la cerradura en Modo Independiente? Por favor usa una llave para secretear a pulsar el boten de representen la parte inferior de Ensamble Interno) acercase 3 segundos hasta que se oyen un largo pitido u dos pitidos cortos. 1.
