Product Manual
30W SLIMLINE LED WORKLIGHT
OWNER'S MANUAL
37816
Thank you very much for choosing an Ultra-Tow product! For future reference, please
complete the owner's record below:
Model: _______________ Purchase Date: _______________
Save the receipt, warranty and these instructions. It is important that you read the
entire manual to become familiar with this product before you begin using it.
This worklight is designed for certain applications only. The distributor cannot be
responsible for issues arising from modification. We strongly recommend this
worklight not be modified and/or used for any application other than that for which it
was designed. If you have any questions relative to a particular application, DO NOT
use the worklight until you have first contacted the distributor to determine if it can or
should be performed on the product.
For technical questions please call 1-800-222-5381.
INTENDED USE
The 30 Watt slimline LED worklight is designed for trucks, SUVs, ATVs, farm
equipment and heavy machinery, with very low amp draw. Aluminum die-cast housing
features a weatherproof design. Magnetic pedestal base provides easy mounting.
TECHNICAL SPECIFICATIONS
10.8in.L x 2.4in.W x 2.9in.H
30 Watt
Store idle worklight. If the worklight is not permanently installed, when
the work light is not in use, store it in a secure place out of the reach of
children. Inspect it for good working condition prior to storage and before reuse.
worklight
Attach the magnetic base (5) on bottom of the bracket（2）by M6 x 15 Hex
socket cap screw (8) .Use one magnetic base per bracket.
Insert M6x18 Hex socket cap screw (7) to bracket（2）and attach the
slider（3） to the screw. Do not over tighten the screw.
Insert the brackets (2) to the installation channel (See Figure 1), then adjust
the angle of the light body that will give you a maximum beam, and then
tighten M6x18 Hex socket cap screws (7).
Select a mounting location on your vehicle, and then put the worklight on the
mounting location.
Attach rubber boot (4) to the bracket (2).Insert M6x25 Hex socket cap screw (9)
to the bottom of bracket (2) and rubber boot(4).
Insert M6x18 Hex socket cap screw (7) to bracket（2）and attach the slider (3) to
the screw. Do not over tighten the screw.
Insert the brackets to the installation channel (See Figure 1), adjust the angle
of the light body that will give you a maximum beam, and then tighten M6x18
Hex socket cap screws (7).
Drill a mounting hole for M6x25 Hex socket cap screw (9) on the mounting
surface. Insert M6x25 Hex socket cap screw (9) to mounting hole on your
vehicle. (The M6x25 Hex socket cap screw inserted to bracket in the first step.)
Then attach M6 spring washer (10), and M6 hex nut (11).
You can also choose permanent mounting; refer to the following directions:
OPERATION
Attach the white wire of 30W slimline LED Worklight to positive electrode of Wire
Harness, and attach the black wire of 30W slimline LED Worklight to negative pole of
Wire Harness. If you are not using the optional wiring kit, we recommend using 18-
ga. wire.
MAINTENANCE
It is recommended that the general condition of the worklight be examined
before it is used. Keep your worklight in good repair by adopting a program of
conscientious repair and maintenance. Have necessary repairs made by
qualified service personnel.
Clean the surface of worklight lens frequently to keep its brightness.
When any malfunction occurs, stop using and repair it immediately as soon as
possible. Please operate your worklight according to the proper operation
procedures
PARTS DIAGRAM & PARTS LIST
For replacement parts and technical questions, please call 1-800-222-5381.
Part#
Qty.
1
2
3
4
5
6
7
8
9
10
11
Description
1
2
2
2
2
2
2
2
2
2
2
Lamp Body
Bracket
Slider
Rubber boot
Magnetic base
Rubber cover
M6x18 Hex socket cap screw
M6x15 Hex socket cap screw
M6x25 Hex socket cap screw (not shown)
M6 Spring washer (not shown)
M6 hex nut (not shown)
Figure 1
1
2
7
3
4
5
8
6