5 500-Lb b. Cap pacity y Elec ctric Traile er Ja ack Owner’s Ma anual W WARNING: : Read careffully and understand all ASSEMBLY A A AND OPERA ATION INSTR RUCTIONS before operatting. Failure to t follow the safety rules and other ba asic safety precau utions may re esult in seriou us personal injury.
Thank you very much for choosing an Ultra-Tow™product! For future reference, please complete the owner’s record below: Serial Number/LotDate Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This trailer jackis designed for certain applications only.
Table of Contents Intended Use ..........................................................................................................................................4 Tools and Components Required .......................................................................................................4 Technical Specifications ......................................................................................................................4 Important Safety Information ................................
Intended Use The Ultra-Tow Electric Trailer Jack attaches to the trailer tongue of a boat, power sport, or equipment trailer. The swivel trailer jack allows the user to move, level, and hitch the trailer with ease. It swivels to a horizontal position during transportation. The 7-way connector plugs into your vehicle connector to let you lift or lower the jack with the push of a button, no hard wiring required.
aware of the environment and ensure that the tool is used in a safe and responsible manner. Do not allow persons to operate or assemble the jack until they have read this manual and have developed a thorough understanding of how it works. Do not modify this jack in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the product. There are specific applications for which the jack was designed. Use the right tool for the job.
injury. ⚠CAUTION TRAILER JACKUSE AND CARE Do not force the trailer jack. Products are safer and do a better job when used in the manner for which they are designed. Plan your work, and use the correct product for the job. Check for damaged parts before each use. Carefully check that the trailer jack will operate properly and perform its intended function. Replace damaged or worn parts immediately. Never operate the trailer jack with a damaged part.
When using the solid caster, make certain the supplied pin is fully inserted through both sides of the inner tube and the drop tube before using the jack. Never attempt to adjust the solid caster when there is any load on the jack.
Assembly Instructions ⚠WARNING Keep hands, feet, and body clear of the jack and trailer to avoid the risk of injury or death! Compare the lift capacity of the jack with your trailer to ensure safe operation of the jack. Before Each Use ⚠WARNING Before each use, inspect jack tubes and replace if bent or damaged. Compare the lift capacity of the jack with your trailer to ensure safe operation of the jack.
trailer. Release the power switch when the motor slows, or switches off, to prevent damage to the motor. Wait 15 seconds for the motor to reset before operating the jack again. Do not stack blocks under the jack’s solid caster. Stacked blocks may become unstable and fall. When using the solid caster, make certain the supplied pin is fully inserted through both sides of the inner tube and the drop tube before using the jack.
be examined before it is used. Keep your tool in good repair. Keep handles dry, clean, and free from oil and grease. Also refer to the engine manufacturer’s instruction manual for additional information about engine maintenance. The following chart is based on a normal operation schedule. Maintenance Interval Maintenance Point The motor is sealed and maintenance-free. Before each use, inspect jack tubes and replace if bent or damaged.
Failure doesn’twork. Possible Cause Bad light bulb. Parts Diagram Page 11 of 14 Corrective Action Replace bulb.
Parts List Part Number 1 2 3 4 5-10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Part Description Crank Rubber Lid Plastic Housing LED Light Switch Extend / Retract Motor Switch Gear Motor Box Assembly Drive Shaft LED Light 20A Automatic Thermal Protection 7-Way Connector ACME Screw Inner Tube Plastic Connector Storage Bracket Outer Tube Swivel Mounting Plate M10 x 100 Hex bolts Flat Washers M10 Lock Washers Bracket Lock Pin Plastic Wheel Hand Crank Handle Quantity 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 4 4 1
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or "Us'') warrants to the original purchaser only ("You'' or "Your") that the Ultra-Tow product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one yearfrom date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.