Installation guide

ManualsBrandsUltra Start ManualsAutomobile ElectronicsKE-6

16001600

1600M1600M

INSTALLATION GUIDE

Advanced Remote Vehicle

Starting System

TECH SUPPORT

Western Canada 1 800 279-0636

United States: 1 866 698-5872

Eastern Canada. Bilingual Support: 1 800 268-0683

E-Mail Tech Support: support@ultrastarters.com

Check Our Web Site: www.ultrastarters.com

16001600

1600M1600M

INSTALLATION GUIDE

Advanced Remote Vehicle

Starting System

TECH SUPPORT

Western Canada 1 800 279-0636

United States: 1 866 698-5872

Eastern Canada. Bilingual Support: 1 800 268-0683

E-Mail Tech Support: support@ultrastarters.com

Check Our Web Site: www.ultrastarters.com

16001600

1600M1600M

INSTALLATION GUIDE

Advanced Remote Vehicle

Starting System

TECH SUPPORT

Western Canada 1 800 279-0636

United States: 1 866 698-5872

Eastern Canada. Bilingual Support: 1 800 268-0683

E-Mail Tech Support: support@ultrastarters.com

Check Our Web Site: www.ultrastarters.com

AUTOMATIC AND MANUAL

TRANSMISSION MODELS

FCC/ID Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the

following conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference

that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the part

responsible for compliance void the user’s authority to operate this devise.

WWW.ULTRASTARTERS.COM

See website for a full size printable version of this manual.

WARNING!! NEVER INSTALL A

AUTOMATIC REMOTE STARTER

IN A MANUAL TRANSMISSION VEHICLE

SERIOUS INJURY OR DEATH CAN RESULT

Summary of content (16 pages)

PAGE 1
INSTALLATION GUIDE 1600 1600M Advanced Remote Vehicle Starting System AUTOMATIC AND MANUAL TRANSMISSION MODELS WWW.ULTRASTARTERS.COM See website for a full size printable version of this manual. WARNING!! NEVER INSTALL A AUTOMATIC REMOTE STARTER IN A MANUAL TRANSMISSION VEHICLE SERIOUS INJURY OR DEATH CAN RESULT TECH SUPPORT Western Canada 1 800 279-0636 United States: 1 866 698-5872 Eastern Canada. Bilingual Support: 1 800 268-0683 E-Mail Tech Support: support@ultrastarters.
PAGE 2
Installation Guide Table Of Contents 1600 Wiring Diagram Pre-Installation What’s Included Pre Installation Check Installation Procedures Wire Connectors 6 Pin Connector 14 Pin Connector 4 Pin Red Connector Jumper Settings Installation Basic Installation - Quick start Under Hood Connections Installing The Antenna Mounting The Module Operating The System Programming Program Overview & System Reset Program Menu 1 (User Settings) Program Menu 3 (Starter Settings) Program Menu 4 (Tach Settings) Operations Singl
PAGE 3
Installation Guide WIRING DIAGRAM Starter Output Yellow (+) 30amp Output Accessory Output Green (+) 30amp Input Main Power Red (+) 30amp Input Main Power Red (+) 30amp Output Selectable Output White (+) 30amp Output Ignition 1 Output Blue 3 4 (-)500ma Output Re-Arm/Output 1* Yellow (-)500ma Output Starer Disable/Output 4* Orange (-)500ma Output Disarm/Output 2* Brown (-)500ma Output Trunk Release/Output 3* Red / White (-)500ma Output Negative When Running White / Violet Ne
PAGE 4
Installation Guide Product Description And Installation Components - Control module - RF Antenna (With Program Switch And LED’s) - 6 pin main harness with dual 30amp power inputs - Hood pin safety switch - 6 button Remote transmitter(s) - 14 pin harness - 4 pin keyless entry harness - Install and Owners manual Feature List - Dual 30amp Power Inputs - Dome Light Supervision - Six button Remote Transmitters - Turbo Timer Mode - Engine Idle Mode - Remote Panic Feature - 5 Programable Auxiliary Outputs - Def
PAGE 5
Installation Guide Wiring Connectors 6 Pin Power Connector Yellow Starter 30amp output 12volts during crank only. Green Accessory 30amp output 12volts in accessory off during start. Red 12 power 30amp input Constant12volt power Red 12 power 30amp input Constant 12volt power. Blue Ignition 1 30amp output 12volts in ignition and start positions. White Selectable 30amp output Selectable Output. Bottom of page. 14 Pin Connector Yellow Arm/Output 1 0.75sec Pulse With Lock And On Shutdown.*See P 11. Orange St.
PAGE 6
Installation Guide Quick Start Installation Step 1 - The Following Wires Must Be Connected! 6 Pin Power Connector Yellow Starter Output Green Heater Output Red 12 power Input Red 12 power Input Blue Ignition 1 Output 14 Pin Power Connector Black System Ground Pink Brake Switch White Park Lights Green/White Hood Pin Blue/White Tach Input Manual Transmissions Only Connect To The Vehicles Starter Wire. Connect To The Vehicles Accessory Wire.
PAGE 7
Installation Guide Programming Introduction Programming Overview Program mode allows you to adjust the settings and options of your system. The system’s default settings do not require any program changes in most cases. However, this system does incorporate a highly advanced programming system that includes 5 menus with numerous options and settings that can be easily adjusted for custom installations. User Settings - Page 8. This menu contains settings that adjust the way the system operates for the user.
PAGE 8
Installation Guide Menu 1 - User Settings Setting 1- Ignition Auto Lock 1 Ignition Lock Enabled 1 Light Flash Lock when ignition is turned On unlock when off 2 Ignition Lock Only 2 Light Flashes Lock when ignition is On, no unlock when Off.
PAGE 9
Installation Guide Menu 3 - Starter Settings Setting 1- Special Door Lock/ Unlock Operations 1 Type 1 2 Type 2 3* Normal Operation 1 Flash 2 Flashes 3 Flashes Unlock before start, lock after start and and shutdown Lock pulse after the remote starter shuts off No additional re-lock pulses Press the Program Switch 1 time to select setting 1 (This will be confirmed by 1 LED flash and one park light flash) Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or hor
PAGE 10
Installation Guide Menu 4 - Tach Settings Setting 1- Method 1- Auto Tach Learn 1) Plug in the module, the park lights will flash and the horn will honk two times.* *If the lights do not flash check connections. Ign must be off when plugged-in. 2) Turn the Ignition Key to the ON position. (The Park Lights will turn on). 3) Start the vehicle with the ignition key, The LED’s on antenna will come on solid when proper tach signal is detected*. The Tach Learning process will take up to 36 seconds.
PAGE 11
Installation Guide Menu 5 - Auxiliary Output Settings New Auxiliary Output Menu. The auxiliary output menu allows the installer to choose the output on a desired wire from the main unit. This option will allow for such things as custom remote features, additional remote starter accessories and button configurations. Enter menu 5 By pressing button 5, located to the left of the # & buttons.
PAGE 12
Installation Guide Auxiliary Output Explanation Of Settings Auxiliary Outputs Ground On Start (Low Current)* This output will supply a 500ma ground output at the same time the starter motor engages. The output will stay on until the starter motor disengages. This output can be used for Low Crank (Bulb Test) activation on the GM Passlock system, GM Daytime Running Lights, Second Starter Relays and Negative starter wire like what is found on the 2001/2002 Dodge Caravans.
PAGE 13
Manual Transmission Vehicles Installation Guide Manual Transmission Remote Starters. Never Install A Automatic Transmission Remote Starter Into A Manual Transmission Vehicle!!! If installing on a convertible vehicle,(NOT RECOMMENDED) Install a radar sensor to protect the proximity of the gear shift lever. The radar should be connected so that if the field is disturbed the radar sensor module will trigger the door or hood input which will cancel the Reservation Mode.
PAGE 14
Installation Guide Other Features Cold Start Mode 1.Press and release the # button, then within two seconds press and hold the button for six seconds. After six second the park lights will turn “On” and the start interval can be selected. 2. While the lights are “On” press the button corresponding to the desired start interval.
PAGE 15
Installation Guide Transmitter Operations Transmitter Programming Step 1 - Within three seconds turn the Key ON-OFF-ON-OFF-ON - Leaving Key ON Step 2 - Press and hold the Program Switch - Parking Lights will come ON **if parklights do not come on at this point, turn key off for 5 seconds, the repeat step 1. Step 3 - Continue to hold the Program Switch until park lights go out.
PAGE 16
Installation Guide Door Lock Diagrams Negative Type Door Locks Vehicle Lock/Unlock Switch Lock To Control Relay or Actuators Un lock Green Blue Positive Type Door Locks Un Lock lock Fused +12V 87 Green 87a 86 Blue Vehicle Lock/Unlock Switch 87 87a 86 85 30 85 30 To Control Relay or Actuator 5 Wire / Reverse Polarity Type Door Locks Fused +12V Green 87 87 87a 86 Blue Vehicle Lock/Unlock Switch 16 Lock Un lock 87a 85 30 86 85 30 x Cut To Actuator x Cut