80 SERIES REV.2007.11.14A Advanced Remote Starters & Vehicle Security Systems TM INSTALLATION GUIDE The manual cover’s the operation of the 1280, 2280, 3280, 3285, 4280 and 4285 Series Remote Starters and Alarm Starters (Including manual transmission models) www.ultrastarters.com FCC ID NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2.
80 SERIES PAGE 2 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 TABLE OF CONTENTS QUICK VIEW WIRING DIAGRAM..........................................................3-4 Connector Pin Configuration Antenna Connector Park Light Jumper MANUAL TRANSMISSIONS.....................................................................5 Park Brake Input Door Pin Connections Clutch Bypass QUICK VIEW PROGRAMMING..............................................................
80 SERIES PAGE 3 QUICK VIEW WIRE DIAGRAM SYSTEM PROGRAMMING - Menu 1 INSTALL MANUAL OUTPUT TO ACTIVATE THE VEHICLES STARTER CIRCUIT YELLOW OUTPUT TO ACTIVATE THE VEHICLES ACCESSORY CIRCUIT GREEN 12VOLT/ 30 AMP MAIN POWER INPUT RED 12VOLT/ 30 AMP MAIN POWER INPUT SELECTABLE OUTPUT* (DEFAULT 2ND IGN) RED OUTPUT TO ACTIVATE THE VEHICLES IGNITION CIRCUIT BLUE (+) SIREN OUTPUT / (-) HORN OUTPUT BROWN** (-) STARTER KILL/ ANTI-GRIND OUTPUT SELECTABLE PARK LIGHT OUTPUT (DEFAULT POSITIVE) ORANGE SY
80 SERIES PAGE 4 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 QUICK VIEW WIRE DIAGRAM OUTPUT TO ACTIVATE DOOR LOCK CIRCUIT (-) GREEN OUTPUT FOR VOLTAGE INVERTER* N/A* OUTPUT TO ACTIVATE DOOR UNLOCK CIRCUIT (-) BLUE PRE-WARN TRIGGER FOR ALARM MODELS (-) FULL TRIGGER FOR ALARM MODELS (-) BLUE** GROUND OUTPUT FOR ADDITIONAL SENSOR (-) BLACK** 12VOLT OUTPUT FOR ADDITIONAL SENSORS (+) RED** (-) WHILE RUNNING OUTPUT (BYPASS TURN ON) GROUND OUTPUT FOR BYPASS MODULE WHT/VIOLET 12VOLT OUTPUT FOR BYPA
80 SERIES PAGE 5 MANUALPROGRAMMING TRANSMISSION-MODELS SYSTEM Menu 1 INSTALL MANUAL MANUAL TRANSMISSION *****YOU MUST INSTALL A “M” SERIES REMOTE START WHEN INSTALLING ON A MANUAL TRANSMISSION VEHICLE***** Connect the following wires for manual transmission vehicles: PARK BRAKE INPUT FOR MANUAL TRANSMISSIONS BLK/WHT Connect this wire to the vehicles Park Brake Switch. The wire should test negative when the park brake is applied only.
80 SERIES PAGE 6 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 QUICK VIEW PROGRAMMING ENTERING PROGRAM MODE 1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON) 2 - Press and release the Program Switch 1 time. (Horn/ Siren will chip to confirm program mode entered) 3 - Select the Program Menu by pressing... Press Lock Press Unlock Press Start Press # MENU 1 MENU 2 MENU 3 MENU 4 4 - Press and Release the Program Switch to advance through the settings.
80 SERIES PAGE 7 QUICK PROGRAMMING VIEW PROGRAMMING SYSTEM - Menu 1 INSTALL MANUAL PROGRAM MODE 1 SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE 1 - see page 16 for detailed instructions SETTING # LED FLASHES SETTING DESCRIPTION OPTION 1 1 CHIRP OPTION 2 2 CHIRPS OPTION 3 3 CHIRPS 1 IGNITION AUTO-LOCK IGNITION AUTO-LOCK / UNLOCK IGNITION AUTO-LOCK ONLY IGNITION AUTO-LOCKS DISABLED 2 HORN / SIREN SETTINGS HORN / SIREN CHIRPS DISABLED HORN/SIREN CHIRPS ENABLED 3 DOOR LOCK PULSE OPTIONS DOUBLE U
0 SERIES PAGE 8 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 QUICK VIEW PROGRAMMING PROGRAM MODE 3 SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE 3 - see page 21 for detailed instructions SETTING # LED FLASHES SETTING DESCRIPTION OPTION 1 1 CHIRP OPTION 2 2 CHIRPS OPTION 3 3 CHIRPS 1 SELECTABLE RELAY 2ND STARTER 2ND ACCESSORY 2ND IGNITION 2 SPECIAL DOOR LOCK OPTIONS UNLOCK BEFORE / LOCK AFTER START LOCK AFTER STARTER SHUT OFF NO ADDITIONAL PULSES 3 GAS / DIESEL MODE NEG GLOW PLUG / 30 SEC DEL
80 SERIES PAGE 9 TACH / TACHLESS LEARNING SYSTEM PROGRAMMING - Menu 1 INSTALL MANUAL AUTO TACH/ TACHLESS LEARNING Start the vehicle with the ignition key. 2 CHIRPS 4 CHIRPS Horn/ Siren will chip to confirm that the Tach/ Tachless has been programmed. To Tach/ Tachless Learn the system simply start the vehicle with the ignition key. To confirm that a proper Tach signal has been programmed the system will chirp the Horn/ Siren and flash the park lights two times.
80 SERIES PAGE 10 INSTALL MANUAL SYSTEM - Menu 1 SYSTEMPROGRAMMING WIRING DETAILS 6-PIN CONNECTOR OUTPUT TO ACTIVATE START CIRCUIT YELLOW OUTPUT TO ACTIVATE ACCESSORY/ HEATER CIRCUIT GREEN 30A HIGH CURRENT 12VOLT INPUT RED 30A HIGH CURRENT 12VOLT INPUT RED SELECTABLE OUTPUT (DEFAULT SECOND IGNITION) WHITE* OUTPUT TO ACTIVATE IGNITION CIRCUIT BLUE 4-PIN CONNECTOR (+) SIREN/ HORN OUTPUT (-) BROWN STARTER-KILL/ ANTI-GRIND OUTPUT ORANGE JUMPER SELECTABLE PARK LIGHT OUTPUT (+ OR -) WHITE SY
PAGE 11 SYSTEMPROGRAMMING WIRING DETAILS SYSTEM - Menu 1 80 SERIES INSTALL MANUAL PIN-1 YELLOW Starter Output-This wire will test 0V when the key is off, in the Accessory position and when the Ignition is in the on position. The starter wire is 12volts during the start/ crank position only. PIN-2 GREEN Heater/Acc Output-This wire will test 0V when key is off, 12volts in the ACC and iIGN positions and off during start/ crank position.
80 SERIES PAGE 12 INSTALL MANUAL SYSTEM SYSTEMPROGRAMMING WIRING DETAILS- Menu 1 13 PIN CONNECTOR OUTPUT FOR FACTORY ALARM RE-ARM OUTPUT FOR FACTORY ALARM DIS-ARM NEGATIVE STARTER OUTPUT OUTPUT FOR TRUNK RELEASE ACTIVATION NEGATIVE ACCESSORY OUTPUT/ AUXILIARY OUTPUT 2 AUXILIARY OUTPUT 1/ PROGRAMMABLE OUTPUT BRAKE SWITCH INPUT (+) WHEN BRAKE IS PRESSED YELLOW BROWN GRAY RD/WHT ORG/WHT WHT/ORG PINK PARK BRAKE INPUT FOR MANUAL TRANSMISSIONS BLK/WHT HOOD PIN SWITCH INPUT TACH WIRE INPUT WAIT TO START (
PAGE 13 SYSTEMPROGRAMMING WIRING DETAILS- Menu 1 SYSTEM 80 SERIES INSTALL MANUAL 1-YELLOW Re-arm(-) (Programmable) Supplies one .75 second pulse when locked and one .75 second pulse after remote start shutdown. Factory alarm re-arm/ RAP shutdown. 2-BROWN Dis-arm(-) Supplies one .75 second pulse when the unlock button is pressed and one .75 second pulse before remote start activation. For factory alarm dis-arm/ “wake up”.
80 SERIES PAGE 14 INSTALL MANUAL SYSTEM - Menu 1 SYSTEMPROGRAMMING WIRING DETAILS 4 PIN AUXILIARY SENSOR CONNECTOR* *ALARM MODELS ONLY PRE-WARN TRIGGER BLUE FULL TRIGGER INPUT GREEN GROUND OUTPUT FOR AUXILIARY SENSOR BLACK 12VOLT OUTPUT FOR AUXILIARY SENSOR RED 1- BLUE Pre-Warn Trigger (-) Input When this wire is grounded by an auxiliary sensor (i.e: Radar Sensor) the system will chirp the SIREN 3 times.
80 SERIES PAGE 15 PROGRAM MODE SYSTEM PROGRAMMING - Menu 1 INSTALL MANUAL ENTERING PROGRAM MODE 1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON) 2 - Press and release the Program Switch 1 time. (The park lights will turn on and the HORN will chip to confirm that program mode was entered) 3 - Select the Program Menu by pressing...
80 SERIES PAGE 16 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE ENTERING PROGRAM MODE 1 IGNITION KEY PROGRAM SWITCH SIREN CHIRP Press and release 1 time Confirming Program Mode 1 CHIRP ON/OFF - ON/OFF - ON (Leaving the key ON) SETTING 1- IGNITION AUTO-LOCKS THE SIREN WILL CHIRP 1 TIME WHEN SETTING 1 IS SELECTED PRESS 1 TIME REMOTE BUTTON Press LOCK Button to Select Menu 1 1 CHIRP 1X CHANGE SETTING 1 - PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S) GOTO SETTING 2 - PRESS & R
80 SERIES PAGE 17 PROGRAM MODE SYSTEM PROGRAMMING - Menu 1 INSTALL MANUAL PROGRAMMING--Menu Menu11 SYSTEM PROGRAMMING SYSTEM CON'T FROM PREVIOUS PAGE SETTING 4- DOOR LOCK TIMING THE SIREN WILL CHIRP 4 TIMES WHEN SETTING 4 IS SELECTED PRESS 1 TIME 4 CHIRP 4X CHANGE SETTING 4 - PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S) GOTO SETTING 5 - PRESS & RELEASE THE VALET SWITCH 1 CHIRP 2 CHIRP 3 CHIRP SETS OPTION 1 - SHORT PULSES- The output for lock and unlock is .25sec.
80 SERIES PAGE 18 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE CON'T FROM PREVIOUS PAGE SETTING 7- PASSIVE LOCKS THE SIREN WILL CHIRP 8 TIMES WHEN SETTING 8 IS SELECTED PRESS 1 TIME 7 CHIRP 7X CHANGE SETTING 7 - PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S) GOTO SETTING 8 - PRESS & RELEASE THE VALET SWITCH 1 CHIRP 2 CHIRP SETS OPTION 1 - PASSIVE LOCK DISABLED- The doors will not lock when Passive Arming sets the alarm.
80 SERIES PAGE 19 PROGRAM MODE SYSTEM PROGRAMMING - Menu 1 ENTERING PROGRAM MODE 2 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM SWITCH SIREN CHIRP Press and release 1 time Confirming Program Mode IGNITION KEY 1 CHIRP ON/OFF - ON/OFF - ON (Leaving the key ON) SETTING 1- VALET SETTINGS THE SIREN WILL CHIRP 1 TIME WHEN SETTING 1 IS SELECTED PRESS 1 TIME REMOTE BUTTON Press UNLOCK Button to Select Menu 2 1 CHIRP 1X CHANGE SETTING 1 - PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S) GO
80 SERIES PAGE 20 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE CON'T FROM PREVIOUS PAGE SETTING 4- SIREN OPTIONS THE SIREN WILL CHIRP 4 TIMES WHEN SETTING 4 IS SELECTED PRESS 1 TIME 4 CHIRP 4X CHANGE SETTING 4 - PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S) GOTO SETTING 5 - PRESS & RELEASE THE VALET SWITCH 1 CHIRP 2 CHIRP 3 CHIRP SETS OPTION 1 - 30 SECOND DURATION- The siren will activate for 30 seconds when the alarm is activated.
80 SERIES PAGE 21 PROGRAM MODE SYSTEM PROGRAMMING - Menu 1 INSTALL MANUAL ENTERING PROGRAM MODE 3 PROGRAM SWITCH IGNITION KEY SIREN CHIRP 1 CHIRP ON/OFF - ON/OFF - ON (Leaving the key ON) Press and release 1 time SETTING 1- SELECTABLE OUTPUT THE SIREN WILL CHIRP 1 TIME WHEN SETTING 1 IS SELECTED Confirming Program Mode PRESS 1 TIME REMOTE BUTTON Press START Button to Select Menu 3 1 CHIRP 1X CHANGE SETTING 1 - PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S) GOTO SETTING 2 - PRESS & REL
80 SERIES PAGE 22 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE SETTING 4- RE-ARM OPTIONS THE SIREN WILL CHIRP 4 TIMES WHEN SETTING 4 IS SELECTED PRESS 1 TIME 4 CHIRP 4X CHANGE SETTING 4 - PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S) GOTO SETTING 5 - PRESS & RELEASE THE VALET SWITCH 1 CHIRP 2 CHIRP 3 CHIRP SETS OPTION 1 - TYPE 2- The rearm output pulses only when the lock button is pressed.
80 SERIES PAGE 23 PROGRAM MODE SYSTEM PROGRAMMING - Menu 1 ENTERING PROGRAM MODE 4 IGNITION KEY INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM SWITCH SIREN CHIRP Press and release 1 time Confirming Program Mode 1 CHIRP ON/OFF - ON/OFF - ON (Leaving the key ON) SETTING 1- TACH OPTIONS THE SIREN WILL CHIRP 1 TIME WHEN SETTING 1 IS SELECTED PRESS 1 TIME REMOTE BUTTON Press # Button to Select Menu 4 1 CHIRP 1X CHANGE SETTING 1 - PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S) GOTO SETTI
80 SERIES PAGE 24 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 RELAY DIAGRAMS DOOR LOCK DIAGRAMS To Control Relay or Actuators Alarm and / or Starter Module NEGATIVE DOOR LOCK (LOW CURRENT) Vehicle's Lock/Unlock Switch Door lock Output Green Blue Ground 87 Alarm and / or Starter Module NEGATIVE DOOR LOCK (LOW CURRENT) Door lock Output 87a Green 86 Vehicle's Lock/ Unlock Switch 12volts 85 30 Blue Ground 87 87a 86 12volts 85 30 USE SPDT 12v Relay Alarm and / or Starter Module POSITIVE D
80 SERIES PAGE 25 RELAY DIAGRAMS SYSTEM PROGRAMMING - Menu 1 INSTALL MANUAL DOOR LOCK DIAGRAMS Ground Alarm and / or Starter Module NEGATIVE ONE WIRE DOOR LOCKS Vehicle's Lock/ Unlock Switch 87 Door lock Output 87a Green 86 12volts 85 30 Blue Ground Lock Resistor 87 87a 86 12volts 85 Unlock Resistor 30 USE SPDT 12v Relay Alarm and / or Starter Module REVERSE POLARITY DOOR LOCK SYSTEM 12volts 87 Door lock Output 87a Green x 86 30 Blue 12volts 87 87a Lock/ Unlock Switch 85 x
80 SERIES PAGE 26 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SHOCK SENSOR SETTINGS ALARM MODELS ONLY 1 - ENTER SHOCK SENSOR ADJUSTMENT MODE + Press & HOLD Lock + Unlock buttons at the same time 3 CHIRPS Continue to hold the buttons for 3-5 seconds until the SIREN Chirps 3 times (Note: System will Arm or Disarm via silent arming prior to entering adjustment mode) 2 - ADJUSTING THE SHOCK SENSOR Each time the lock button is pressed and released the sensitivity will INCREASE by 1 level.
80 SERIES PAGE 27 QUICK VIEW OPERATIONS SYSTEM PROGRAMMING - Menu 1 INSTALL MANUAL SYSTEM PROGRAMMING 1 QUICK VIEW OPERATION- Menu CHART BUTTON LENGTH OF PRESS CHIRPS / FLASHES SYSTEM OPERATION 1 SECOND 3 SECONDS 1 SECOND (PANIC OR ALARM) 1 1 OFF LOCK / ARM ALARM ACTIVATE PANIC ALARM/ PANIC OFF 1 SECOND 1 SECOND (PANIC OR ALARM) HOLD FOR 3 SECONDS 2 OFF 2+1 UNLOCK / DISARM ALARM/ PANIC OFF UNLOCK + TRUNK 1 SECOND 1 SECOND WHEN RUNNING 3 SECONDS W/ REMOTE START 1 1 2 REMOTE START EXTENDED RUN
80 SERIES PAGE 28 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 TRANSMITTER PROGRAMMING TRANSMITTER PROGRAMMING The system can lean up to 4 different remote’s. Each remote to be used MUST be programmed together during the same sequence. For security, when a new remote is programmed all previous remote’s are deleted. Please see remote operation chart for information on using Second Car / Pad Lock Operations.
PAGE 29 MANUALPROGRAMMING TRANSMISSION- Menu 1 SYSTEM 80 SERIES INSTALL MANUAL RESERVATION MODE Manual transmission remote starters must be set into Reservation Mode before the remote starter will activate. The activation type of Reservation Mode is determined when the system is installed. Auto Reservation Mode (Default) 1- While the vehicle is running, place into neutral and apply the park brake. 2*- Press and release the brake pedal twice. The park lights will flash twice, the SIREN or HORN (opt.
80 SERIES PAGE 30 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 TABLE OF CONTENTS DIAGNOSTICS CHART If the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic to indicate what shutdown input has been triggered. For example: If the start button is pressed the park lights flash 3 times slowly.
PAGE 31 NOTES PROGRAMMING - Menu 1 SYSTEM 80 SERIES INSTALL MANUAL
80 SERIES PAGE 32 INSTALL MANUAL **FOR DETAILED VEHICLE WIRING INFORMATION GO TO: http://www.ultrastarters.com/wiring_diagrams.html This site is for registered and authorized dealer only. If you are an authorized dealer but have been registered, please fill out the service request form at http://www.ultrastarters.com/wiring_diagrams.html PRODUCT INFORMATION: www.ultrastarters.com TECHNICAL SUPPORT: support@ultrastarters.com ORDERING: orders@ultrastarters.
