Quick Operation Guide Ultimax 1200 Ultimax 1300 Ultimax 1400
Quick Operation Guide of DS-7200-SH/SV Series DVR Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable to DS-7204HVI-SH, DS-7208HVI-SH, DS-7216HVI-SH; DS-7204HFI-SH, DS7208HFI-SH, DS-7216HFI-SH; DS-7204HWI-SH, DS-7208HWI-SH, DS-7216HWI-SH; DS-7204HVI-SV, DS7208HVI-SV and DS-7216HVI-SV series DVR.
Quick Operation Guide of DS-7200-SH/SV Series DVR 3. Connect the HDD to the motherboard of the DVR with the included data cable. 4. Connect the power cable to the HDD. 5. Re-install the cover of the DVR and fasten screws.
Quick Operation Guide of DS-7200-SH/SV Series DVR Front Panel The front panel of DS-7200-SH/SV is shown below: Table 1 Description of Control Panel Buttons No. Name Function Description 1 POWER POWER indicator turns green when DVR is powered up. 2 STATUS STATUS indicator lights in red when data is being read from or written to 3 Tx/Rx 4 USB Interface 5 IR Receiver HDD. Tx/Rx indictor blinks green when network connection is functioning properly.
Quick Operation Guide of DS-7200-SH/SV Series DVR 6 Alarm In/Out Connector for alarm input/output. 7 AUDIO IN RCA connector for audio input. 8 AUDIO OUT RCA connector for audio output. 9 LAN Interface Connector for LAN (Local Area Network). 10 RS-485 Interface Connector for RS-485 devices. Connect the D+ and D- terminals to T+ 11 12V 12VDC power supply. 12 POWER GND Switch for turning on/off the device. Ground (needs to be connected when DVR starts up).
Quick Operation Guide of DS-7200-SH/SV Series DVR 1. Disconnect pluggable block from the ALARM IN /ALARM OUT terminal block. 2. Press and hold the orange part of the pluggable block; insert signal cables into slots and release the orange part. Ensure signal cables are in tight. 3. Connect pluggable block back into terminal block. RS-485 Connections To connect RS-485 devices (e.g.
Quick Operation Guide of DS-7200-SH/SV Series DVR Specifications Table 3 Specifications for DS-7200HFI-SH 7
Quick Operation Guide of DS-7200-SH/SV Series DVR Model Video/Audio input Video/Audio output DS-7204HFI-SH External interface General DS-7216HFI-SH 8-ch 16-ch Video compression H.264 Video input 4-ch Video input interface BNC (1.0 Vp-p, 75 Ω), PAL /NTSC self-adaptive Audio compression G.711 Audio input 1-ch / 4-ch, RCA (2.0 Vp-p, 1 kΩ) Two-way audio input 1-ch, RCA (2.
Quick Operation Guide of DS-7200-SH/SV Series DVR Table 4 Specifications for DS-7200HVI-SH 9
Quick Operation Guide of DS-7200-SH/SV Series DVR Model Video/Audio input Video/Audio output DS-7204HVI-SH DS-7208HVI-SH DS-7216HVI-SH 8-ch 16-ch Video compression H.264 Video input 4-ch Video input interface Audio compression Audio input BNC (1.0 Vp-p, 75 Ω), PAL /NTSC self-adaptive Two-way audio input HDMI/VGA output 1-ch, RCA (2.0 Vp-p, 1 kΩ) (using the audio input) CVBS output Encoding resolution Frame rate G.711 1-ch / 4-ch, RCA (2.
Quick Operation Guide of DS-7200-SH/SV Series DVR Table 5 Specifications for DS-7200HVI-SV Model Video/Audio input Video/Audio output DS-7204HVI-SV 16-ch Video input 4-ch Video input interface Audio compression BNC (1.0 Vp-p, 75 Ω), PAL /NTSC self-adaptive G.711 Audio input 1-ch / 4-ch, RCA (2.0 Vp-p, 1 kΩ) Two-way audio input HDMI/VGA output 1-ch, RCA (2.0 Vp-p, 1 kΩ) (using the audio input) Frame rate General 8-ch H.
Quick Operation Guide of DS-7200-SH/SV Series DVR Table 6 Specifications for DS-7200HWI-SH 12
Quick Operation Guide of DS-7200-SH/SV Series DVR Model Video/Audio input Video/Audio output DS-7204HWI-SH Video compression H.264 Video input 4-ch Video input interface Audio compression BNC (1.0 Vp-p, 75 Ω), PAL /NTSC self-adaptive G.711 Audio input 1-ch / 4-ch, RCA (2.0 Vp-p, 1 kΩ) Two-way audio input HDMI/VGA output 1-ch, RCA (2.
Quick Operation Guide of DS-7200-SH/SV Series DVR 14
Quick Operation Guide of DS-7200-SH/SV Series DVR HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate 96K 128K 160K 192K 224K 256K 320K 384K 448K 512K 640K 768K 896K 1024K 1280K 1536K 1792K 2048K Storage Used 42M 56M 70M 84M 98M 112M 140M 168M 196M 225M 281M 337M 393M 450M 562M 675M 787M 900M Note: Please note that supplied values for storage space used is just for reference.
Quick Operation Guide of DS-7200-SH/SV Series DVR Menu Operation Menu Structure The menu structure of the DVR is shown as below: Note: You can right click on the Shutdown button to exit the main menu. Startup and Shutdown Proper startup and shutdown procedures are crucial to expanding the life of the DVR. Before you start: Check that the voltage of the extra power supply is the same with the device’s requirement, and the ground connection is working properly. Starting up the device: Steps: 1.
Quick Operation Guide of DS-7200-SH/SV Series DVR 2. Click the Shutdown button to enter the following dialog box: 3. Click the Yes button. The following message box pops up: 4. Turn off the power switch on the rear panel of DVR. Using the Setup Wizard The Setup Wizard can walk you through some important settings of the device. By default, the Setup Wizard starts once the device has loaded. Operating the Setup Wizard: 1. Select the system language from the drop-down menu. The default language is English.
Quick Operation Guide of DS-7200-SH/SV Series DVR 2. Check the checkbox to enable Setup Wizard when device starts. Click Next to continue the setup wizard. You can also click Cancel to exit the Setup Wizard, or use the Setup Wizard next time by leaving the “Start wizard when device starts?” checkbox checked and exit. 3. Click Next button on the Wizard window to enter the Login window. 1) Enter the admin password. By default, the password is 12345.
Quick Operation Guide of DS-7200-SH/SV Series DVR 5. Click Next button which takes you back to the Network Setup Wizard window. Set the network parameters, including the NIC type, IPv4 address, IPv4 subnet mask, default gateway, etc. You can enable the DHCP to automatically obtain an IP address and other network settings from that server. 6. Click Next button to enter the HDD Management window. To initialize the HDD, click the Init button. Initialization removes all the data saved in the HDD. 7.
Quick Operation Guide of DS-7200-SH/SV Series DVR 4) Click Copy to copy the record settings of the current camera to other camera (s) if needed. 5) Click OK to return to the Record Settings window. 8. Click OK to complete the startup Setup Wizard. Live View Some icons are provided on screen in Live View mode to indicate different camera status.
Quick Operation Guide of DS-7200-SH/SV Series DVR Table 7 Mouse Operation in Live View Icon Name Main Menu Description Enter the main menu of the system. Single Screen Switch to the single full screen live view mode. Multi-screen Switch to multi-screen live view mode. Note: The multi-screen icon varies according to the device models. Normal Record Start all-day normal recording for all channels. Motion Detection Record Playback Start motion detection recording for all channels.
Quick Operation Guide of DS-7200-SH/SV Series DVR Control icon to enter the PTZ toolbar.
Quick Operation Guide of DS-7200-SH/SV Series DVR 3. In the pop-up message box, click Yes to finish the quick recording settings for all channels. Note: The full-screen motion detection triggered recording is configured by default in this mode. Playback Play back the record files of a specific channel in the live view menu. Instant Playback by Channel Choose a channel under live view using the mouse and click the button in the quick settings toolbar.
Quick Operation Guide of DS-7200-SH/SV Series DVR The channel and time selection menu will display by moving the mouse to the right of the playback interface. Tick the channel or channels if you want to switch playback to another channel or execute simultaneous playback of multiple channels. Backup Recorded files can be backed up to various devices which connected with the DVR, such as USB flash drives, USB HDDs or a DVD writer. To export recorded files: 1. Enter Export interface.
Quick Operation Guide of DS-7200-SH/SV Series DVR 2. Set search conditions and click Search button to enter the search result interface. 3. Select record files you want to back up. Click button to play the record file if you want to check it. Check the checkbox before the record files you want to back up. Note: The size of the currently selected files is displayed in the lower-left corner of the window. 4. Export the record files. Click Export button and start backup.
