Instructions / Assembly

OPERATING INSTRUCTIONS
BASIC FUNCTION
LED INDICATING LAMP
KEY SWITCH
PIR MOTION SENSOR
1
2
 BOOT PREHEATING
♦ Day or night, there will be 15±5 seconds of warm-up time after the product is
powered on for the first time,at this time, the bulb will be on at 100% brightness.
It will automatically enter TEST MODE after it is preheated.
 TEST MODE
♦ Day or night,the brightness of the bulb will be reduced to 40% after the startup is
preheated,when human activity is detected,brightness will be increased to 100%,
until 5±3 seconds after the human body left the detection range, the brightness
level again dropped to 40%
 AUTO MODE
♦ The product will automatically enter AUTO MODE and the LED indicator will blink for 4 times
when the time reaches 120±20 seconds after startup preheating.
♦ Turn o the power switch in TEST MODE and turn it on within 3 seconds to enter AUTO MODE directly.
♦ In MANUAL OVERRIDE 8H MODE, reset to AUTO MODE after turning o the power switch and turning it on within 3 seconds.
♦ In AUTO MODE, the light is not on during the day. When the ambient light brightness reaches
the starting condition (20~90LUX) at night, the bulb will be steady on at 40% brightness
(at this time, it is in two-step mode, and the bulb will not be on in single-step mode).
When human activity is detected, the bulb will be on at 100% brightness. Until 120±20 seconds
after the human body leaves the detection range, it will return to 40% brightness to be steady on
(That is in two-step mode, in single-step mode, the bulb will be turned o). When the ambient light
reaches the o condition (MAX. 600LUX) and 60±10 seconds later, the bulb will be automatically
extinguished.
 LED INDICATING LAMP
♦ When entering single-step mode, the LED indicator flashes once.
♦ When entering the two-step mode, the LED indicator flashes twice.
♦ When human activity is detected, the LED indicator flashes once.
♦ When entering AUTO MODE, the LED indicator blinks 4 times.
♦ When entering MANUAL OVERRIDE 8H MODE, the LED indicator quickly blinks 6 times.
♦ When exiting MANUAL OVERRIDE 8H MODE, the LED indicator quickly blinks 3 times.
 CIRCUIT BREAKER RESET
♦ After the power is o for more than 5 seconds, the product will re-enter the preheating state after the power is turned on again.
♦ The product has the function of memory. After the power failure reset, the power will keep the single or double step mode before
the power failure.
♦ Single or double - step mode can be switched through the key switch in front of the sensor. Every time a key switch is pressed,
the product returns to TEST MODE, day or night, in any mode.
♦ Two-step mode: When human activity is detected, the light bulb will turn on 100% brightness, until the human body out of the
detection range for a certain period of time, the light bulb will drop to 40% brightness, and then turn on 100% brightness again
when the next human activity is detected.
 SINGLE/DOUBLE STEP MODE DESCRIPTION AND SWITCHING
♦ Single-step mode: When human activity is detected, the bulb will turn on 100% brightness,after a certain period of time, the bulb will
automatically turn o. When the next human activity is detected, the bulb will turn on 100% brightness again.
 MANUAL OVERRIDE 8H MODE
♦ It can only be accessed in AUTO MODE. When the ambient light reaches the starting condition (20~90LUX)
at night, turn o the power switch and turn it on within 3 seconds, enter MANUAL OVERRIDE 8H MODE,
and the LED indicator will blink for 6 times quickly,at this time, the bulb will keep on bright for 8±1H. When
the ambient light reaches the o condition (MAX. 600LUX) after 8±1H and 60±10 seconds, the bulb will
automatically turn o and return to AUTO MODE.
* Note: This state is two-step mode,if it is single-step mode, the bulb will be o
after the startup is preheated. After human activity is detected, the bulb will light
up to 100% brightness, and it will be o again 5±3 seconds after the human body
leaves the detection range.
OPERATING INSTRUCTIONS
TROUBLESHOOTING
 When selecting a location, mounting the fixture too high or in front of a sloped surface, such
as an uphill walkway or driveway, may aect the motion sensor's eectiveness.
The light does not turn
on when there is motion.
Bulb won't light.
The light comes on for
no apparent reason.
The light comes on
during the daytime or
too early in the evening.
The light comes on too
late in the evening.
1 . Too much sunlight is shining onto sensor in
the early evening.
2. Too much light is shining onto sensor due
to another light source, such as a street lamp
or other light fixture.
3. Moving persons or vehicles are below the
view of the motion sensor because motion
sensor is mounted too high.
1 . Wall switch or circuit breaker is o.
2. Light bulb may be dead.
3. Light bulb is loose.
4. Incorrect or loose wire connections.
5. Power is o.
1 . Street or sidewalk trac is triggering the
motion sensor.
2. False triggering caused by a heat source,
such as a heater or dryer vent, or heated
swimming pool.
The fixture may be installed in a shaded
area, such as under a porch or eave,
preventing daylight from shining onto
the photocellsensor.
Too much sunlight is shining onto the sensor
in the early evening.
1 . Relocate fixture away from a western facing wall.
2. a- Eliminate or turn o other light source.
b- Block other light source from shining onto
photocell sensor.
c- Relocate fixture.
3. Relocate fixture to a lower position or to a
dierent location.
1 . Turn on switch or circuit breaker.
2. Test the light bulb in a known working light fixture,
replace bulb as needed.
3. Tighten light bulb in socket.
4. Check wire connections.
5. Make sure power supply is on.
1 . Relocate fixture to a dierent location.
2. a- Eliminate heat source.
c- Relocate fixture.
Relocate fixture
Relocate fixture away from a western facing wall.
 When selecting a location, be aware of the motion sensor is more sensitive to movement
across its coverage area and less sensitive to movement toward or away from the motion sensor.
 Select locations away from heat sources, such as heating vents, air conditioners,and heated
swimming pools.
 Select locations away from nighttime light sources, such as street lamps or other light fixtures.
They may shine light onto the fixture's sensor. This light might cause the circuit to "think" that
it is daytime.
 Be aware that shade from a porch or an eave may not allow eno onto the photocell sensor and
may cause the circuit to "think" that it is nighttime, and subsequently cause the light to come on
during the daytime.
 The detection range of the sensor shall not be blocked by the screen, furniture, large bonsai or
other isolation objects.
 The input end of the sensor is not suitable for installing dimmers, only suitable for directly
connecting to the standard input voltage
 Sensor away from electromagnetic wave products, such as WIFI router /WIFI camera, away from
more than 2 meters to prevent electromagnetic wave interference.
 Operating temperature range: -30°C~50°C
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Least Sensitivity
PIR MOTION SENSOR
Best Sensitivity
PIR MOTION SENSOR
5.9'~7.2' (1.8m~2.2m)
min 29.51' (9m)
PIR MOTION SENSOR
220
o
PIR MOTION SENSOR
SELECTING A LOCATION
ADDITIONAL NOTE
DETECTION RANGE (at 25˚C)
 Rated voltage: 120VAC/60Hz; The bulb should be installed at less than the rated power of the sensor;
Energy-saving lamp/LED 45W; Incandescent lamp 60W.
 When the ambient temperature is 25°C and the sensor is suspended 1.8m~2.2m above the ground,
the sensor's detection Angle is 220° and the detection distance is min 9m.
45W
60W
LED
LED
ELECTRICAL PARAMETER