Data Sheet

62977 20190523
UHU GmbH & Co. KG 77813 Bühl (Baden) Tel.: [phone] Fax [phone]
www.uhu.com
Note: This information is the result of carefully executed tests. This Technical Data Sheet has been prepared to the best of our knowledge to provide you with advice when gluing. We cannot be held responsible for the
results or any damage suered, as the variety of factors involved (type and combination of materials and working method) are beyond our control. Users have to carry out their own checks and trials. Liability can only be
accepted for the consistently high quality of our product.
Crystal Clear fast dual-Component epoxy adhesive
plus sChnellfest
62977  UHU PLUS SCHNELLFEST DOUBLE CHAMBER SYRINGE BLISTER 27 G DE/FR/IT  45725
Tools: Mix the components in the double-syringe by means of the supplied
mixing bowl and spatula.
APPLICATION
Mixture ratio: 1:1 (by volume)
Coverage: 1 ml = approx 1 cm² at a lm thickness of 1 mm
Directions for use:
Remove the spatula from the side of the double syringe, and the closure cap
from the handle. Break the seal of the double syringe. Press out an equal
amount of both components onto the enclosed mixing tray. Mix these two
equal parts well with the synthetic spatula. Apply the mixture, which at room
temperature (+20°C) remains toolable for about 5 minutes, as a thin layer
on one of the two materials. Assemble the material and keep it in place for
20 minutes. Be careful not to move the parts before the adhesive has cured.
After use place the special cap in the handle on the double syringe. Resin and
hardener must not come into contact with each other unless for usage.
Potlife: 5 minutes
Stains/residue: Remove wet stains immediately with warm water and soap.
Cured adhesive residue can only be removed mechanically.
Advice: Some types of synthetics can not be joined such as polyethylene and
polypropylene. This can be tested by holding a glowing copper wire against the
synthetics. Does it smell of wax? Then you can not bond it.
Use a piece of adhesive tape in order to keep the parts in place while the
adhesive is curing.
Points of attention: After use close well (note: always place back the cap
in the same way, due to the bonding of the cap to the double syringe). For
optimum performance it is important to create a larger amount of adhesive and
mix it very well. Curing time depends on the temperature. Adhesive does not
cure below +5°C.
CURE TIMES*
Drying/Curing time: approx. 5 minutes
Final bonding strength after: approx. 12 hours
* Curing time may vary depending on a.o. surface, product quantity used, humidity level and ambient
temperature.
TECHNICAL PROPERTIES
Moisture resistance: Good
Water resistance: Good
Temperature resistance: -40°C - +100°C
UV resistance: Very good
Chemicals resistance: Very good
Paintability: Good
Filling capacity: Very good
TECHNICAL SPECIFICATIONS
Appearance: Opaque liquid
Chemical base: Binder: Epoxy Resin; Hardener: Polymer
Bonding technique: 1-sided application
Colour: Crystal Clear
Consistency: Medium viscosity
PRODUCT DESCRIPTION
Crystal clear fast dual-component epoxy adhesive. Water resistant, quick, very
strong.
FIELD OF APPLICATION
Suitable for fast, strong and invisible repair of many materials, such as pottery,
porcelain, glass, leather, wood, stone, metal, ceramics. Both with themselves
and in combination. Not suitable for Polyethylene (PE), polypropylene (PP),
PTFE and silicone rubber.
PROPERTIES
· Fast
· Crystal clear
· Super-strong
· Universal, suitable for many materials
· Resistant to temperatures between -40°C and +100°C
· Filling
· Water resistant
· Chemical resistant
· Paintable
PREPARATION
Working conditions: Only apply at temperatures between +5°C and +35°C.
Product cures by mixing the resin and hardener.
Personal safety: Preferably wear gloves.
Surface requirements: The surface must be dry, clean and free of dust and
grease.
Preliminary surface treatment: Degrease parts to be bonded with acetone.
Roughen smooth surfaces (sandpaper).