MSDS

MATERIAL SAFETY DATA SHEET
PRODUCT NAME: DRYLOK E-1 EPOXY FLOOR PAINT – ALL COLORS HMIS CODES: H F R P
PRODUCT CODE: 82, 83, 84, 85, 87 1 0 0
SECTION I – MANUFACTURER IDENTIFICATON
MANUFACTURE’S NAME: UNITED GILSONITE LABORATORIES EMERGENCY PHONE: [phone]
ADDRESS: 1396 JEFFERSON AVENUE
SCRANTON, PA 18509 INFORMATION PHONE: [phone]
NAME OF PREPARER: R. BARAKO
DATE ISSUED: APRIL 2013
SUPERSEDES: FEBRUARY 2010
SECTION II – HAZARDOUS INGREDIENTS/SARA III INFORMATION
OCCUPATIONAL EXPOSURE LIMITS VAPOR PRESSURE WEIGHT
HAZARDOUS COMPONENTS CAS NUMBER OSHA PEL ACGIH TLV OTHER mmHg@TEMP PERCENT
WATER 7732-18-5 NOT ESTAB NOT ESTAB NOT ESTAB 1.0 (68F) 57
ALUMINUM SILICATE 1332-58-7 15 MG/M
3
10 MG/M
3
NOT ESTAB N/A 6
ACRYLIC COPOLYMER NOT ESTAB NOT ESTAB NOT ESTAB NOT ESTAB N/A 20
DIPROPYLENE GLYCOL MONO-
BUTYL ETHER 29911-28-2 NOT ESTAB NOT ESTAB NOT ESTAB .060 (68F) 2
PROPYLENE GLYCOL 57-55-6 NOT ESTAB NOT ESTAB NOT ESTAB 0.2 (68F) 2
TITANIUM DIOXIDE 13463-67-7 15 MG/M
3
10 MG/M
3
NOT ESTAB N/A 10
BLACK IRON OXIDE 1317-61-9 10 MG/M
3
5 MG/M
3
NOT ESTAB N/A 1
YELLOW IRON OXIDE 51274-00-1 10 PPM (STEL) 5 MG/M
3
NOT ESTAB N/A 1
RED IRON OXIDE 1332-37-2 10 PPM (STEL) 5 MG/M
3
NOT ESTAB N/A 1
STEL = SHORT TERM EXPOSURE LIMIT
No toxic chemical (s) subject to the reporting requirements of Section 313 of Title III and of CFR 372 are present
SECTION III – PHYSICAL/CHEMCIAL CHARACTERISTICS
BOILING RANGE: 212 F SPECIFIC GRAVITY (H2O = 1): 1.18
VAPOR DENSITY: HEAVIER THAN AIR EVAPORATION RATE: SLOWER THAN ETHER
COATING V.O.C.: DOES NOT EXCEED MAXIMUM VOC 250 G/L (VOS 2.09 LB/GAL)
SOLUBILITY IN WATER: SOLUBLE
APPEARANCE AND ODOR: WHITE OR COLORS, PRODUCT SPECIFIC. TYPICAL AMINE ODOR
SECTION IV – FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: N/A METHOD USED: N/A
FLAMMABLE LIMITS IN AIR BY VOLUME: LOWER: N/A UPPER: N/A
EXTINGUISHING MEDIA: NONE KNOWN
SPECIAL FIRE FIGHTING PROCEDURES: CONTAINERS MAY SWELL AND BURST DURING A FIRE DUE TO INTERNAL PRESSURE CAUSED BY
HEAT. THIS MAY CAUSE A SLIPPERY CONDITION ON FLOORS
UNUSUAL FIRE AND EXPLOSION HAZARDS: N/A
SECTION V – REACTIVITY DATA
STABILITY: PRODUCT IS STABLE
CONDITIONS TO AVOID: TEMPERATURES BELOW 32 (F) FOR STORAGE. TEMPERATURES BELOW 50 (F) FOR APPLICATION
INCOMPATIBILTY (MATERIALS TO AVOID): N/A
HAZARDOUS DECOMPOSITION OR BYPRODUCTS: N/A
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR