DM505 1000V Digital Multimeter INSTRUCTION MANUAL ENGLISH DM505 Apo V RANGE MIN/MAX HOLD FAST SEL µA mA A 600V CAT III 1000V CAT II mAµA A 10A MAX FUSED 400mA MAX FUSED 1-800-547-5740 www.ueitest.com • email: info@ueitest.
TABLE OF CONTENTS FUNCTIONS .................................................................................................................................................. 3 FEATURES ..................................................................................................................................................... 3 GENERAL SPECIFICATIONS ..................................................................................................................... 3 CATEGORY DEFINITIONS...........
FUNCTIONS • 1000V AC/DC • Audible continuity • 10A AC/DC • Capacitance 9999µF • Resistance 40MΩ • Milliamps/Microamps • Diode test FEATURES • Auto/Manual ranging • Test lead holders • Auto power off • Kick stand • Min/Max • High resolution backlit display • Hold • Auto selection • 1 ms Fast response Min/Max • Fused test lead inputs • Low battery indicator • Rubber boot GENERAL SPECIFICATIONS • Operating Temperature: 32˚ to 122˚F (0˚ to 50˚C) • Storage Temperature: -44˚ to 122˚F (-20˚ to 5
IMPORTANT SAFETY WARNINGS WARNING Read entire Safety Notes section regarding potential hazards and proper instructions before using this meter. In this manual the word “WARNING” is used to indicate conditions or actions that may pose physical hazards to the user. The word “CAUTION” is used to indicate conditions or actions that may damage this instrument. WARNING To ensure safe operation and service of the tester, follow these instructions.
OVERVIEW J DM505 A Apo V B C D E RANGE MIN/MAX HOLD FAST K H L M I SEL µA F mA A N O mAµA A G 10A MAX FUSED 400mA MAX FUSED MAX CAT III 600V CAT II 1000V A. Apo: Auto power off after 30 minutes of use. Press and hold the HOLD button while turning the meter on to disable Apo. B. Digital Backlit Display C. Range Button: • Press to change from auto ranging to manual ranging. • Press repeatedly to select proper range.
SYMBOLS Negative AC/DC Voltage or Current Low Battery Overload: Range Exceeded Auto power off Active Maximum measured value displayed Hold/Capture Value Minimum measured value displayed A Voltage Microamps nF mA µF Microfarad Amps Diode milliamps Ground nano Farads Ohms/Resistance Continuity Warning or Caution Fuse Auto-ranging Dangerous Levels Auto Auto Selection High Voltage Indication AC/DC Voltage: <1000V AC/DC WARNING • Use CATIII rated Test leads or higher.
Resistance: <40MΩ DM505 Apo V AT RANGE MIN/MAX HOLD FAST SEL µA mA A Features: mAµA A MAX CAT III 600V CAT II 1000V 400mA MAX FUSED 10A MAX FUSED MIN/MAX RANGE HOLD WARNING • Do not measure resistance on a live circuit. Ranges Accuracy Resolution Overload Protection 600Ω to 6MΩ 40MΩ ±(0.8% +5 dgts) ±(1.5% +5 dgts) 0.1Ω to 0.001MΩ 0.
Diode BAD DIODE GOOD DIODE Open Diode Displays "OL" Both directions DM505 Forward Bias Displays approx. voltage drop Apo V V RANGE MIN/MAX Apo V or Apo V HOLD FAST SEL '0' Both directions (shorted) µA mA A • Forward voltage drop if forward biased. • “OL” if reverse biased. mAµA A 10A MAX FUSED 400mA MAX FUSED MAX CAT III 600V Features: CAT II 1000V Open Circuit Voltage Overload Protection Approx.: <3.
AC/DC Microamps: 6000µA AC/DC Milliamps: 400mA DM505 DM505 Apo Apo V µ A AT RANGE MIN/MAX m AT HOLD RANGE MIN/MAX FAST SEL µA mAµA 10A MAX FUSED Features: HOLD FAST SEL A V A RANGE 400mA MAX FUSED µA mA mA A A µA CAT II 1000V MIN/MAX mAµA A MAX CAT III 600V HOLD 10A MAX FUSED 400mA MAX FUSED MAX CAT III 600V CAT II 1000V mA SEL ACµA Ranges Accuracy Resolution 600µA to 6000µA ±(1.2% +5 dgts) 0.
AC/DC Amps: <10A DM505 Apo V A AT RANGE MIN/MAX HOLD FAST SEL µA mA A mAµA A 10A MAX FUSED 400mA MAX FUSED WARNING • Do not attempt to measure more than 10A AC. MAX CAT III 600V A CAT II 1000V Features: AC AMPS Ranges RANGE Accuracy MIN/MAX Resolution 6A to 10A ±(1.5% +5 dgts) 0.001A to 0.01A Minimum sensitivity: 500mA AC (auto selection mode only) HOLD SEL Overload Protection 11A/1000V Fast fuse CAUTION: 20A overload for 30 seconds max.
Battery Replacement • When the batteries are too low for safe operation, the Low Battery indicator will display. AA AA S/N: S/N: FCC/IC INFORMATION NOTE: This device complies with Part 15 of the FCC Rules and CAN ICES-3(A). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations.
WARRANTY The DM505 is warranted to be free from defects in materials and workmanship for a period of 2 years from the date of purchase. If within the warranty period your instrument should become inoperative from such defects, the unit will be repaired or replaced at UEi’s option. This warranty covers normal use and does not cover damage which occurs in shipment or failure which results from alteration, tampering, accident, misuse, abuse, neglect or improper maintenance.
