WIRELESS BRIDGE USER MANUAL Model: CPE850 Tips: Thank you for ordering and using UeeVii CPE850 Wireless Bridge, please read the manual carefully before use. If there are any problems during the use, please contact us in time. The installation of this device requires some network knowledge. If you can't install it, please let us know or contact a professional. Customer Service Email: support@ueevii.
OVERVIEW 1. Introduce UeeVii CPE850 is a long-distance 5.8G wireless transmission device. It uses wireless communication technology to transmit network data using air as a medium to perform long-distance point-to-point or point-to-multipoint inter connection. The working data link layer realizes the interconnection of local area networks. The transmission distance can reach up to 5KM. CPE850 Video Bridge Transmission usually consists of two devices in AP and Client mode respectively.
10. Dynamic MIMO power saving mode (DMPS) and APSD； 11. Support 24V POE power supply, easy to install and deploy； 12. Support WEB GUI access management device. 3. Specifications Brand UeeVii CPU 7620A+7612E+IP1001 Model Flash DRAM Interface Data rate Transfer method Modulation CPE-850 8MByte DDR2 64MByte 10/100/1000Mbps LAN*1 & 10/100Mbps LAN*1 11a: 54M,48M,36M,24M,18M,12M,9M,6Mbps 11n: 7.2M,14.4M,21.7M,28.9M,43.3M,57.8M,65M,72.2M, 14.4M28.9M,43.3M,57.8M,86.7M,115.
.Package Included 2 * CPE850 Gigabit Bridge 2 * Gigabit POE Adapter (24V) 2 * Cat 5e Network Cable 2 * Metal Hoop 1 * User Manual 5.Interface Details Digital Tube DC(Unavailable) Reset Button 1000Mbps 100Mbps LAN A-B Button B-LED LED Gigabit PoE Adapter 1000Mbps LAN Port PoE Port 5.1. Button Operation Reset Button: Press and hold for 10S to reset the wireless bridge; in setup mode, short press once to toggle a different character to pairing.
6.LED Indicator Details Receiver A Mode Transmitter B Mode LED Light Description LAN1/LAN2 The data connection is successful, the LED light is on, otherwise, it is not bright. Digital Tube Digital display LED display "H" indicates manual configuration status Signal Lights After the bridge is connected successfully, the WLAN light will be on, not connected the WLAN light will not be lit.
Quick Start 1. PoE Power Supply The CPE850 wireless bridge adopts a PoE power supply, which is easy to install and manage while saving costs. 1.1. According to the requirements, prepare a long enough network cable （ Recommended within 20 meters, must Cat 5e or up） to connect the wireless bridge and the PoE power supply. The PoE port of the PoE power supply is connected to the WAN port of the wireless bridge. 1.2.
3.Point to Multipoint Pairing Step: 1 master bridge with 3 slave bridges 1. Switch one unit to A(Master Bridge) and 3 units to B(Slave Bridge); 2. Connect the POE to each unit using the Ethernet cable and plug the POE in; 3. Wait for them to power up, about 2 min; 4. Use the tiny reset button to click through until you get a channel with a letter. 1,2,3,..., A,B,C,...,F, here used C; 5. Then on the other 3 unit do the same. 4 units need to be on the same channel; 6.
3. Connect the PoE adapter PoE to CPE, and LAN to Camera, PC, Router or Switch based on the network topology. The role of PoE is to provide power and data transmission for CPE. 4. The master CPE’s PoE adapter’s LAN connection monitors the Internet, and the slave CPE’s PoE adapter LAN connects cameras or routers and other equipment. Note: For point-to-point installation, the line of sight of the 2 wireless bridge brackets must be clear and cannot pass through the wall.
6. Application Case 6.1 Case 1: Point-to-point extended network WiFi range suitable for extending the network to second buildings, such as garages, shops, barns,etc. Master Bridge Slave Bridge Router Computer Router POE POE Router device(AP mode) 6.2 Case 2: Point-to-point extended of surveillance cameras range Master Bridge Slave Bridge IP Camera Computer DVR Switch IP Camera IP Camera 6.
6.4 Case 4: Point-to-point extended surveillance cameras range Master Bridge Slave Bridge IP Camera Computer DVR IP Camera IP Camera Advanced settings Note: You can enable the device without advanced settings. Computer Access 1. Connect the CPE to the computer Refer to the figure left to connect the CPE to the computer through a PoE adapter and an Ethernet cable. AP POE Charger POE support@ueevii.
2. Modify your computer's IP address, make your computer's IP and the bridge's IP address be on the same network segment(LAN) so that you can access them. Step 1: Find and open "Open Network and Sharing Center" on your computer. Tips： click the network icon in the lower right corner of the computer. Step 2：Find and open the "Change adapter settings", select "Local Area Connection" to right-click to open the network properties.
4. On the login screen, the default user name and login password of the wireless bridge is "admin", just entry password login. Note: “admin” is not the password of the WiFi SSID, it is just the password for WEB access. 5. Login successful, go to setting. 6. In the wireless settings, turn off "Hide SSID", then modify the SSID name and WiFi password, and finally click "Apply" to complete the setting. support@ueevii.
Digital & IP & WiFi Correspondence Chart You can check the SSID and password through this chart. （Ps:In this chart, SSIDs and Passwords are the default.） 12 support@ueevii.
Troubleshooting Trouble Reason Solution Packet Latency 1. Wireless interference 2. Distance is too long, or there are some walls between them 3. CPE's angle in the wrong direction, weak signal 1. Use WiFi analysis to choose the best channel 2. CPE should be in the normal distance, and avoid the wall 3. Adjust the angle of CPE according to signal strength Wrong Password 1. Forget the password 2. Input wrong password 3. Too much cookie 4.
System LED light off Low transmission Rate Device always dead 1. PoE power supply is not working 2. Some problem in CPE's PoE port 3. Ethernet cable is loose, RJ45 port is wrong power current/voltage lower or wrong 1. Check if the PoE adapter or PoE switch work 2. Check if the PoE port of CPE is ok 3. Check if Ethernet cable is loose if Ethernet cable plugged into PoE port 4.
Technical Support and Service A. Thank you for your order and for using UeeVii Wireless Bridge, please read the manual carefully before use. If there are any problems during the use, please contact us in time; B. The installation of this device requires some network knowledge. If you can't install it, please let us know or contact a professional. Tech Service Email: support@ueevii.com support@ueevii.
