Installation Guide

1.
3.
BEFORE YOU BEGIN INSTALLATION: Read and understand all of the installation instructions contained within
this manual. Improper installation could result in product failure or personal injury, and may void the warranty.
IMPORTANT: Before installing your new UDECX Portable Patio Deck, you must LEVEL the area where you intend to
install your system, or at the location of each Pier (A).
IMPORTANT: If you intend to install a UDECX optional railing system on your Patio Deck, read and understand
Steps 17 through 25 prior to installing your Patio Deck.
(NOTE: When selecting an area for your patio deck, keep in mind that the more level the area, the simpler the in-
stallation. Areas with sloping grade will require more excavation or the purchase of optional shims and risers to
level the piers. The Starter Kit you purchased is designed to be assembled into a 10’ x 10’ patio deck, however, the
components can be arranged in a variety of configurations. Individual components are available to expand and
personalize your Patio Deck configuration and size. Learn more at www.udecx.com)
Determine where you
would like to install your
UDECX Patio Deck and
measure off a 10’ X 10’ or
selected area. (Fig. 1)
Level the soil or grade and
remove all vegetation
(grass or plants) at each
Pier (A) location. (Fig. 2)
Place an Anchor Spike (D) through the center of the 1” hole in the Pier (A). (Fig. 5) Install the Anchor
Spike (D) with a hammer or hand sledge. (NOTE: Be very careful not to hit the Pier (A) with a hammer,
hand sledge or other tool that might damage the Pier (A).
LEAVE SPACE between the head of the Anchor Spike (D) and the top of the Pier (A). (Fig. 6)) This
provides wiggle room for adjusting the location of the Pier (A) when necessary. (Fig. 7) Level Pier (A)
in each direction.
2.
Place the first Pier (A) at an
outside corner of the 10’ X
10’ area you measured off.
(Fig. 3)
If you plan to install next to
a building or structure of
any kind, place the edge of
the first Pier (A) 1” away
from the exterior wall.
(Fig. 4)
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6 Fig. 7
6
19
Leave a minimum of
1/4” (.25”) space
13.
14.
15.
Si usted decidio instalar en un
terreno inclinado o que no
esta nivelado, los Shims de
1” (G) (Fig. 29) o los Risers de
3” (H) (Fig.30) pueden ser uti-
lizados para elevar partes de
su UDECX patio portatil y asi
ayudar a a nivelar la superficie
terminada.Solo coloque un
Shim debajo del PIER (A),
nivele y empieze a instalar
siguiendo los Pasos 4 al 8 de
este manual.
NO COLOQUE mas de 2
Shims de 1” (G) (Fig.31) o
mas de dos Risers de
3” (H)debajo de ningun Pier
(A) (Fig.32)
Los Shims de 1” (G) y los
Risers de 3” (H) pueden ser
usados entre si. SIEMPRE
coloque el Shim o Shims de
1” (G) debajo del Riser de
3” (H). NUNCA use mas de 2
Shims (G) con ningun Riser de
3” (H). (Fig.33)
(NOTA: Todos los Risers
(H) ,Shims (G) y Piers (A)
deberan asegurarse con los
Picos de 18”) (Fig 34)
16.
El terreno puede variar debido
al lugar de la instalacion,por
lo tanto, la planeacion
cuidadosa y adecuada de la
nivelacion del terreno para el
sistema completo debera ser
desarrollado por la persona
que instala.La superficie para
su UDECX Patio Portatil no
debera exceder 12 “ de la
base del piso o terreno.
(Fig.35)
Fig. 30
Fig. 29
Fig. 32
Fig. 31
Fig. 34
Fig. 33
Fig. 35
Para Nivelar y Elevar su UDECX Patio Portatil
IMPORTANTE: Si Usted desea comprar e instalar los componentes para nivelacion de UDECX: Shims de
1” (G), y/o Risers de 3” (H), Ud. necesitara asegurar el Pier (A) y todos los Shims de 1” (G) o los Risers de
3” (H) con un PICO de 18” (J).Ver la Fig 34.