Bluetooth Communication Adapter WT300 User Manual
Welcome to WT300 Bluetooth Audio Adaptor User Manual Contents of the retail box Remote Control WT300 Audio Adaptor Charging Cables AC/USB Charger Stereo cable Rubber grip Walkie Talkie Cables User Manual 2
CONTENTS Contents of the Retail Box -------------------------------- 2 Contents ---------------------------------------------------- 3 Overview General -------------------------------------------------- 4 WT300 at a Glance ------------------------------------- 5 PTT Remote Control at A Glance ----------------------- 7 Walkie-talkie Cables ------------------------------------ 8 Rubber Grip --------------------------------------------- 9 Pairing WT300 with UClear Headset Advanced Communication Mode ---------
OVERVIEW General WT300 as Universal Bluetooth Adaptor Kit The UCLEAR WT300 is capable of connecting non-Bluetooth audio devices eg. Two-way radios, PTT/iDEN phones, GPS/ Radar Detector or mp3 players to Bluetooth headsets wirelessly. Compatible Bluetooth devices include any Bluetooth headsets which support HFP or A2DP (Advanced Audio Distribution Profile) Bluetooth profiles.
OVERVIEW WT300 At A Glance Front View Multi-function Button Charging/ Walkie Talkie Port LED Status Indicator Stereo Audio-in/ Aux-in Reverse Reset Button Before using the device, please charge it first! Charging o Please use the mini-USB charging cable to connect the device to a USB port. o The LED indicator would show solid red during charging and turns solid blue when it is fully charged. o The charging time is normally less than 2 hours.
OVERVIEW WT300 at A Glance Power On o Press and hold the Multi-function button for 2 seconds and the light indicator will flash blue while device powers up. o In idle mode, pressing the Multi-function button once will trigger the device to attempt to connect to the last paired device in the range. Power Off o Press and hold Multi-function button for 5 seconds. o The LED indicator will blink red 5 times as device powers off.
OVERVIEW PTT Remote Control at A Glance LED Indicator Charging Socket PTT Button Before using PTT Remote control, please charge it first! Charging o Please use the micro-USB charging cable to connect the device to a USB port. o While charging, the LED status indicator will show solid red. o When fully charged, the indicator light will go off. Low Battery Indicator o When the LED indicator blinks red 3 times at 3-second interval, the PTT remote control needs to be charged.
OVERVIEW Cables Model num to walkie-talkie to WT300 Walkie-talkie cables have different audio plug, they can be identified by the model number imprinted on it. Model Number Walkie-talkie WC-10 Motorola compatible WC-11 Uniden compatible WC-12 Motorola compatible Charging Cables Mini-USB Micro-USB There are 2 type of charging cable included in the package. Cable with micro-USB plug is for charging the remote control whereas mini-USB plug is for the WT300 adaptor. Stereo Audio Cable 3.
OVERVIEW Rubber Grip Rubber grip Remote control PTT Motorbike handle bar The rubber grip can be used to install the remote control unit on the motorbike handle bar.
UCLEAR HEADSET [COMMUNICATION MODE] Pairing If you have a UCLEAR helmet communicator, you can select the Advanced Communication Mode on your WT300 to enjoy the special features below: a) Walkie Talkie Mode b) Additional way to activate PTT from the UCLEAR headset c) Connecting your UCLEAR headset to a cell-phone and intercom (another UCLEAR headset) at the same time. Advanced Communication Mode Pairing Please make sure your UCLEAR headset and WT300 are turned off.
UCLEAR HEADSET [COMMUNICATION MODE] Quick Setup To complete setup of the system, follow the steps below. Step 1: Link the walkie talkie to the WT300 Choose the right walkie talkie cable supplied (WC-10, WC11, WC-12) which is compatible with your walkie talkie. Connect walkie talkie cable to the WT300 by inserting the mini-USB end into the WT300 and the 2.5mm/3.5mm audio jack into the walkie talkie. Set the walkie talkie volume to mid-range. Please refer to Walkie Talkie Volume Setting section.
UCLEAR HEADSET [COMMUNICATION MODE] Quick Setup Step3: Connect UCLEAR headset and WT300 Both devices must be switched on. Press the Multi-function button on the WT300 once, it will attempt to connect to the UCLEAR headset. The LED indicator of both devices will continue to flash blue light twice every 2 seconds when they are connected. Manual PTT using the UCLEAR control unit To talk, press and hold the Answer button on the UCLEAR headset.
UCLEAR HEADSET [COMMUNICATION MODE] Quick Setup Useful Tips To initiate/disconnect UCLEAR headset from the WT300, press and hold the Down button for 2 seconds on the UCLEAR headset. The WT300 will be automatically disconnected once the intercom or mobile phone features on the UCLEAR control unit are initiated. To manually power off the UCLEAR headset, disconnect it from the WT300 first by holding Down button 2 seconds. Then press and hold the Answer button for 5 seconds.
UCLEAR HEADSET [COMMUNICATION MODE] MMI Table WT300 Adaptor Button Configuration Command Action Power on Press/hold Multi-function for 2 seconds Power off Press and hold Multi-function for 5 seconds Pairing Device should be switched off; Press and hold Multi-function for 5 seconds Connect to UCLEAR Press Multi-function once headset Reset Press Reset once WT300 Adaptor Status Indicator State Sequence Idle Blink blue slowly Busy Blink blue quickly Power down Blink red 5 times Pairing Blin
UCLEAR HEADSET [COMMUNICATION MODE] MMI Table Remote Control PTT Button Configuration Command Action Connect to WT300 Press PTT once To talk Press & hold PTT To listen Release PTT Reset Device will reset upon charging Power on/off Not necessary Pairing Not necessary Remote Control Status Indicator State Sequence Busy Blink blue fast Low Battery Blink red 3 times every 3 seconds Battery Charging Solid red Battery full - The UCLEAR headset will produce four beep tones at 1 minute inter
UCLEAR HEADSET [COMMUNICATION MODE] MMI Table UCLEAR headset PTT Button Configuration, applicable to HBC100, HBC120, HBC130.
BLUETOOTH HEADSET [HFP MODE] Pairing 1 2 1 3 1 This section is a step by step guide to pair the WT300 Bluetooth adaptor with a non-UCLEAR headset or generic Bluetooth headset that supports HFP (handsfree profile). Pairing with Bluetooth Headset using HFP First, you must pair the WT300 with your Bluetooth headset. Pairing needs to be done only once for the headset. Please make sure your WT300 is turned on. Put the headset into pairing mode. Refer to your headset’s manual for pairing instructions.
BLUETOOTH HEADSET [HFP MODE] Quick Setup To complete setup of the system, follow the steps below. Step 1: Link walkie talkie to the WT300 Choose the right walkie talkie cable supplied (WC-10, WC11, WC-12) which is compatible with your walkie talkie. Connect walkie talkie cable to the WT300 by inserting the mini-USB end into the WT300 and the 2.5mm/3.5mm audio jack into the walkie talkie. Set the walkie talkie volume to mid-range. Please refer to Walkie Talkie Volume Setting section.
BLUETOOTH HEADSET [HFP MODE] Quick Setup Step 3: Link the WT300 adaptor to the Bluetooth headset If the Bluetooth headset is on, press the Multi-function button of the WT300 adaptor to connect it to the headset. The WT300 indicator will blink blue fast. If the Bluetooth headset is off, turn it on. The headset will autoconnect to the WT300 adaptor (switched on). Please refer to your headset manual for detail.
BLUETOOTH HEADSET [HFP MODE] Quick Setup Voice Command PTT (VOX) The WT300 adaptor is capable of actuating the PTT button through voice activation Press the Multi-function button on the WT300 adaptor quickly 3 times. You should hear a beep tone indicating VOX is enabled. To talk, say ‘Hello’ loudly to trigger the PTT. The status indicator on the WT300 will show a red light during talk. Being silent for 2 seconds will switch to the listening mode.
BLUETOOTH HEADSET [HFP MODE] MMI Table WT300 Adaptor Button Configuration Command Action Power on Press/hold Multi-function button 2 seconds Power off Press/hold Multi-function 5 seconds Pairing Device should be in on state.
BLUETOOTH HEADSET [HFP MODE] MMI Table Remote Control PTT Button Configuration Command Action Connect to WT300 Press PTT once To talk Press & hold PTT To listen Release PTT Reset Device will reset upon charging Power on/off Not necessary Pairing Not necessary Remote Control Status Indicator State Sequence Busy Blink blue fast Low Battery Blink red 3 times every 3 seconds Battery Charging Solid red Battery full - You will hear four beep tones in 1 minute intervals when the WT300 adaptor o
MUSIC STREAMING MODE [A2DP] Pairing The WT300 Bluetooth adaptor is designed to work with most Bluetooth stereo headsets. The WT300 can connect to most audio sources such as MP3 players via the provided stereo cable. Before you use the WT300 for music streaming, it must be paired with a Bluetooth stereo headset or headphone. Pairing as Music Adaptor Power on the WT300 adaptor first. For pairing instructions for the headset, refer to your headset manual.
MUSIC STREAMING MODE [A2DP] Quick Setup After the pairing process, please follow the steps below to setup the system. Your WT300 and headset must be turned off. Step 1 : Connect the WT300 to the Music Device Attach the WT300 to the music device player with the provided stereo audio cable. Play the music. For good audio quality, set the volume on the music device to about 80% full. Step 2 : Power on the Stereo Headset Please refer to your headset user manual.
MUSIC STREAMING MODE [A2DP] MMI Table WT300 Adaptor Button Configuration Command Action Power on Press/hold Multi-function 2 seconds Power off Press/hold Multi-function for 5 seconds Pairing Device should be switched on.
WALKIE TALKIE VOLUME SETTING It is very important to calibrate your walkie talkie volume setting to the optimum level so that you will receive the best audio quality on the headset. If the volume setting deviates too much from the optimum point, you may experience the following: a) Volume through headset is not loud enough ; b) Speech is muffled and/or has hissing background noise.
AUX INPUT MODE For GPS/Radar Detector Aux In The WT300 Aux-in port can be interfaced to most GPS and Radar detector audio output via the 3.5mm stereo cable. You can listen to the GPS voice navigation information or Radar detector warning at the same time while you are using the Walkie Talkie. Connect to GPS or Radar Detector The WT300 adaptor must be paired with UClear headset or compatible Bluetooth headset in communication mode. For pairing instructions for the headset, refer to your headset manual.
REMOTE CONTROL PAIRING The remote control PTT unit is already factory paired to the WT300 adaptor. You do not need to re-do pairing for the remote control unless it is absolutely necessary. To pair your remote control to a new WT300 adaptor, make sure both devices are in power-off state. Charge the PTT remote control. While charging, hold the PTT button for 5 seconds until the blue and red indicator(purple) blink simultaneously.
Technical Data for WT300 Bluetooth Adaptor WT300 Adaptor Specification Unit Dimensions (L x W x H) 85mm x 52mm x 26mm Weight 57g Audio Frequency response 30Hz to 20kHz Sampling rate 48kHz, 16 bit THD 0.5% Bluetooth Specifications Version 2.1 EDR, Class 2 Profiles AGHFP, A2DP, RFCOMM Radio Carrier frequency 2.402 – 2.480 GHz Range Up to 10m (open field) RF output power -6 dBm to 4 dBm Power Power consumption 100mW (max) Power input (charging) 5V / 500mA Built-in battery 3.
Technical Data for PTT Remote Control Remote Control Specification Unit Dimensions (L x W x H) 101mm x 17mm x 7mm Weight 12g Bluetooth Specifications Version 2.1 EDR, Class 2 Profiles RFCOMM Radio Carrier frequency 2.402 – 2.480 GHz Range Up to 10m (open field) RF output power -6 dBm to 4 dBm Power Power consumption 50mW (max) Power input (charging) 5V / 100mA Built-in battery 3.
Notices WARNING: BATTERY WARNING: The UCLEAR® Bluetooth WT300 audio adaptor and PTT remote control contain rechargeable lithium ion polymer batteries. To reduce risks of fire or burns, do not disassemble, crush, puncture, short external contacts or dispose in fire or water. CHARGING NOTICE: To reduce the risk of personal injury, electrical shock, fire or damage to equipments, please follow all the instructions below: - Do not immerse the product, AC adaptor in water.
Notices The sender will bear all transportation charges for functioning products but which were declared defective. LIMITATIONS OF WARRANTY: All product warranties for the product by UCLEAR® are limited to those mentioned in the product manual.
Notices agents, distributors, suppliers, resellers and all others in its supply and distribution chain either due to the designer’s or manufacturer’s negligence or omissions or any third parties involved. Always comply with the local law and traffic regulations. Where use of the product is not permitted or allowed by any laws and regulations including the traffic laws of your country, we warn you not to go against such restrictions.
Notices CORRECT DISPOSAL OF THIS PRODUCT: Do not dispose this product with other household wastes at the end of its working life. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
Notices TECHNICAL SUPPORT: For additional information please visit our website at www.uclear-digital.com For technical support please contact us at: support@uclear-digital.com Phone: 1-855-BIT-WAVE COPYRIGHTS: Copyright © 2011 BITwave Pte Ltd & FSC. All rights reserved. No part of this guide may be reproduced in any form or by any process whatsoever without prior written consent from BITwave Pte Ltd and FSC. LICENCES: The UCLEAR® trademark and logo is exclusively owned by BITwave Pte Ltd & FSC.
Notices FCC COMPLIANCE STATEMENT FCC ID: NMC-WT300,NMC-PTT300 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Notices IC COMPLIANCE STATEMENT ICID: 9858A-WT300, 9858A-PTT300 This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This Class【B】 digital apparatus complies with Canadian ICES003. Cet appareil s’accorde avec Industrie Canada licence-exempte RSS standard.
Notices NCC Warning 經型式認證合格之低功率射頻電機，非經許可，公司、商號 或使用者均不得擅自變更頻率、加大功率或變更原設計之特 性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信； 經發現有干擾現象時，應立即停用，並改善至無干擾時方得 繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。低功率 射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性 電機設備之干擾。 38
