HBC 200 ® Helmet Communicator User Manual ® US-PUB#1G
Welcome to ® HBC200 Helmet Communicator User Manual HBC200 helmet communicator control unit Metal mounting bracket & velcros for speakers A clip bracket & anti slip rubber patch 1 Hi-fi stereo headset Notices This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Notices TECHNICAL SUPPORT: For additional information please visit our website at www.uclear-digital.com For customer and technical support in the US and Canada, please contact: BITwave USA LLC 1093 E lron Eagle Dr. #115 Eagle, ID 83616 1-855-BIT-WAVE COPYRIGHTS: Copyright © 2012 BITwave Pte Ltd. All rights reserved. No part of this guide may be reproduced in any form or by any process whatsoever without prior written consent from BITwave Pte Ltd.
Quick User Guide Notices Your HBC200 at a glance GENERAL FUNCTIONS Before using your HBC200 please charge it first! Answer Button Up Button Status Indicator Charge Check Bluetooth phone capabilities before use. To charge, use the provided charging cable by connecting it either to a USB port or to the adaptor provided. While charging, the status indicator light will be red. Upon fully charged, the status indicator light will be blue.
Quick User Guide Notices All risks from operating or usage of the product rest solely and entirely with the user of this product, the original purchaser or any third parties, who assumes full responsibility for all injuries, losses and/ or damages, whether caused in whole or in part by the negligence, omissions or other conduct of others, including that of BITwave, FSC and all their representatives, partners, agents, distributors, suppliers, resellers and all others in its supply and distribution chain eit
Quick User Guide Notices Warranty does not cover data recovery and physical deterioration due to use, damages resulting from accidents, storage, loss or data loss or damage during repairs or transits. The sender will bear all transportation charges for functioning products but which were declared defective. Answer Incoming Call Use voice pickup, say ‘hello’ or ‘pickup’. OR Manually press Answer button once. Last Number Redial Use voice pickup, say ‘hello’ or ‘pickup’.
Quick User Guide Notices BATTERY WARNING: The helmet communicator contains a rechargeable lithium ion polymer battery. To reduce risks of fire or burns, do not disassemble, crush, puncture, short external contacts or dispose in fire or water. CHARGING NOTICE: To reduce the risk of personal injury, electrical shock, fire or damage to equipments, please follow all the instructions below: - Do not immerse the product, AC adaptor or speakers in water.
Warning and Safety Instructions This manual uses the and Below is an explanation of the icons. icons to highlight certain instructions. Attention > This icon highlights special instructions and precautions intended to avoid damage to the system. Non-compliance may void the product warranty. Warning > This icon provides precautions important to prevent injuries to the user.
Technical Data Warnings and Safety Instructions Unit > Prolonged exposure to loud sounds may lead to permanent hearing damage. Dimensions (L x W X H) 75mm x 45mm x 26mm Weight 36g > Do not attempt to place an outgoing call through the mobile phone while riding on the motorcycle at any point of time.
Features Status Indicator Configurations Summary The helmet communicator has three main functions: to make mobile phone calls, to listen to music and for intercom communication. The table below shows the status indicator configurations. Mobile Phone Functions • Bluetooth phone audio capabilities, HFP & HSP Profile. • Voice activated call pick up. Music Streaming Functions • Bluetooth music streaming with hi-fi and stereo capabilities, A2DP Profile.
Button Configurations Summary Installation The table below shows the status indicator configurations. Action Button The HBC200 helmet communicator package contains : 1.
Installation GPS Device Install Speakers To use a GPS device with the UClear HBC200, the two must first be paired. 1. Use the velcros to install the speakers into the ear cavity of the helmet. Pairing the HBC200 to a GPS Device •Turn on the HBC200 helment communicator and GPS device 2. The microphones facing out. •To connect the helmet communicator to a GPS device, hold the Up and Down buttons for 2 seconds. This puts the helmet communicator into paring mode.
Intercom Operations Installation Intercom, Phone Call and Music Switching Your HBC200 helmet communicator package comes with 2 types of mounting brackets: a clip bracket and a metal mounting bracket. Use either of the brackets to install the HBC200 control unit onto your helmet. All the intercom units can be connected to phone during operation. Phone call has the highest priority.
Installation Intercom Operations Install Metal Mounting Bracket 1. Identify a position on the helmet to adhere the Metal Mounting Bracket. Private Conversation Mode During group intercom, you can have private conversation with the user who has performed a 2-party intercom pairing with you. For example, to setup private conversation with your passenger 1.Perform a 2-party pairing with your passenger first. 2.Perform a group intercom pairing with all other users.
Intercom Operations General Operations Large Group Intercom (Three-parties or more) Your You can daisy-chain multiple HBC200 units to form bigger group intercom. A chain of 10 or more parties is achievable.To setup group intercom, you must first pair all the HBC200 units. Pairing process needs to be carried out only once. HBC200 helmet communicator is now all set and ready to go! The operations described here are applicable to all modes of operations.
General Operations Intercom Operations Charging the Unit • To charge the helmet communicator, connect the provided charging cable to the speaker/ charging socket. Upon charging, if the unit is on, the system will automatically initiate power down. Two-Party Intercom To use the intercom for the first time, you must pair your communictor to another HBC200 unit. Volume Control • The volume control of the helmet communicator can be controlled using the Up and Down buttons.
Intercom Operations New Generation Mulit-Hop Technology -Superior voice quality -Allows large group communication -Multiplies range through hopping Mobile Phone Operations To use the helmet communicator with your mobile phone for the first time, you must first connect them wirelessly by pairing. Pairing •To connect the helmet communicator to a mobile phone, hold the Up and Down buttons for 2 seconds. This puts the helmet communicator into paring mode.
Mobile Phone Operations Music Streaming Operations Last Number Redial •To redial the last number, hold the Up and Answer buttons for 2 seconds. The capability of this function is dependent on the mobile phone used. To use the helmet communicator with your music devices you must connect them wirelessly through Bluetooth pairing. This step is only required for Bluetooth music streaming devices.
