ZIGBEE/BLE/THREAD MODULE SERIES M7B-Q95 HARDWARE REFERENCE MANUAL FCC: 2AWGH-M7B-Q95-B IC: 26146-M7BQ95B HVIN: B4 PMN: BLEnd/Z M7B-Q95B
1. OVERVIEW The ubisys wireless connectivity module series M7B-Q95-B -power wireless system on chip, which comprises an ARM Cortex-M4, 512KB flash ROM, 64 KB SRAM and a multi-channel, multi-protocol radio with quasi-concurrent support for IEEE 802.15.4 (zigbee, rf4ce, Thread) and Bluetooth Low Energy (BLE). Additional flash memory is available on the module to store over-the-air upgrade images or other data.
Copyright© 2018 2020 ubisys technologies GmbH, Düsseldorf, Germany. All rights reserved. 3 www.ubisys.
2. CONTENTS 1. Overview 2 2. Contents 4 3. Features 5 M7B-Q95-B4 (Form Factor B, Pinout Scheme #4) 3.1.1. Light Firmware Pin Assignments 4. Test and Late Customization Interface 5. Mounting 6. 7. 9. 8 9 10 M7B-Q95-B 10 Horizontal Mounting 10 Vertical Mounting 10 Electrical Paramaters 12 Absolut Maximum Ratings 12 Recommended Operating Conditions 12 General Purpose Input Output Specifications 12 Radio Characteristics 12 Physical Dimensions 13 M7B-Q95-B 8.
3. FEATURES - Designed in Germany using high-quality, enduring parts for many years of life expectancy MCU: Advanced 32-bit ARM Cortex-M4 running at 32MHz with 64KB SRAM and 512KB flash ROM PHY: 10dBm transmit power, -98dBm receiver sensitivity Integrated chip antenna Low power dissipation Multi-channel, multi-mode transceiver Pre-loaded firmware, for instance dimmable light with switch input for local control Customizations available 5 www.ubisys.
M7B-Q95-B4 (Form Factor B, Pinout Scheme #4) Status: Active.
This results in the following mapping of often used peripheral I/Os (LED, PWM, UART1, UART2, SPI master/slave, I²C master/slave) and analogue inputs, together with resulting wake-up and interrupt request capabilities Module GPIO ANIO IRQ 1 Port Wakeup LED PWM UART1 UART2 SPI Pin I2C Master SPI I2C Slave Y1/X7 23 2 C 4 Y 0 2 - TX MISO SDA MOSI SDA Y2/X6 26 5 C 7 Y 3 5 TX - MOSI SCL MISO SCL Y3/X5 25 4 C 6 Y 2 4 RX TX SCLK SDA SSN SDA Y4/X4 24 3 C
3.1.1. Light Firmware Pin Assignments Software uses the following mapping of functions to module pins: Module Pin Y0 Function Type Description GND G Ground Y1/X7 GPIO23 D/O Light Output #3 Y2/X6 GPIO26 A/I Voltage Monitoring for Over-Voltage Protection Y3/X5 GPIO25 A/I Temperature Monitoring for Over-Temperature Protection Y4/X4 GPIO24 A/I Current Monitoring for Over-Current Protection Y5/X3 VDD P Power supply, 3.
4. TEST AND LATE CUSTOMIZATION INTERFACE Depending on the pre-loaded firmware version, a test and late-customization interface with accompanying tools is available. This is a two-wire interface, where the module acts as an I2C slave, and a production tool acts as I2C master. This interface allows late changes to the factory block for OEMs, and other application specific customizations and test modes. Please contact ubisys support for additional details. 9 www.ubisys.
5. MOUNTING M7B-Q95-B The M7B-Q95-B module was designed for horizontal or vertical mounting. Based on the application one of these can be chosen. On boards where large components could affect the antenna performance the vertical mounting offers a second option. Horizontal Mounting In a horizontal position the module is soldered in by using the soldering pads on the left and right side. All pads are designed to solder the module by hand or reflow.
The M7B-Q95-B module can be mounted in a vertical position by using the soldering pads on the short side of the module. It can be soldered between pin rows of a 2-row 1.27mm pin header (2x8) or in slot on the base board with soldering pads at the edges of the slot. 11 www.ubisys.
6. ELECTRICAL PARAMATERS Absolut Maximum Ratings Absolut Maximum Ratings Min Max Units Supply voltage, VCC I/O pin voltage Input RF level, PMAX Storage temperature Operating temperature Soldering temperature -0.3 -0.3 3.6 3.6 +10 -40 +85 +260 V V dBm °C °C °C Recommended Operating Conditions Power Maximum Ratings Min. Typ. Max. Units Supply voltage, VCC Supply current, ICC Ambient Temperature, TA 1.8 3.6 -40 3.3 12mA 25 85 V V °C Min. Typ. Max. Units 0.6 1.1 VDD 0.25 V V 0.6 0.
7. PHYSICAL DIMENSIONS M7B-Q95-B 13 www.ubisys.
8. SOLDERING Lead-free reflow soldering Do not reflow solder with the module on the bottom side of the main PCB. The module might fall off the PCB during that process. Make sure that it is placed on the top side while reflow soldering. Hand soldering Hand soldering is possible. Follow IPC recommendations (reference document IPC-7711) when using a soldering iron. 14 www.ubisys.
9. ORDERING INFORMATION The following tables list the product variants available. Use the specified order code for your orders. Please contact ubisys support if you require any customization. Order Code Part Name Description 1427 x x x M7B-Q95-B4 ZigBee Light Application 15 www.ubisys.
10. GENERAL TERMS & CONDITIONS OF BUSINESS When placing your order you agree to be bound by our General Terms & Conditions of Business, http://www.ubisys.de/en/smarthome/terms.html 16 www.ubisys.
11. PRODUCT APPROVALS Federal Communications Commission (FCC) Approvals The ubisys M7B-Q95-B with integrated Antenna has been tested to comply with FCC CFR Part 15 (USA). This device complies with Part 15.247 of FCC Rules. FCC statement: This device complies with part 15 of the FCC Rules.
If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed 11.1.1. FCC Labelling Requirements When integrating the M7B-Q95-B into a product it must be ensured that the FCC labelling requirements are met.
Le fonctionnement est soumis aux deux conditions suivantes : (1) ce dispositif ne doit pas causer d'interférences, et (2) ce dispositif doit accepter toute interférence, y compris celles qui peuvent provoquer un fonctionnement non souhaité du dispositif. Ce module est conforme aux limites d'exposition aux radiations RF fixées par la FCC et Industrie Canada pour la population générale.
12. DECLARATION OF CONFORMITY Declarations of Conformity for the M7B-Q95-B module have been issued by ubisys technologies GmbH, which cover radio emissions, electromagnetic compatibility and immunity. These documents are available from our website or on request. 20 www.ubisys.
13. REVISION HISTORY Revision 0.1 0.2 0.3 Date 10/03/2020 08/12/2020 10/01/2020 Remarks Initial Draft Version Physical dimensions added Product approvals defined more precisely 21 www.ubisys.
14. CONTACT UBISYS TECHNOLOGIES GMBH NEUMANNSTRASSE 10 40235 DÜSSELDORF GERMANY T: +49 (211) 54 21 55 - 00 F: +49 (211) 54 21 55 - 99 www.ubisys.de info@ubisys.de 22 www.ubisys.
