4K Indoor/Outdoor IP Camera with Infrared and Optical Zoom Model: UVC-G4-PRO
Package Contents UVC-G4-PRO Screw Anchors (Qty. 2) Tightening Tool Self-Tapping Screws (Qty. 2) Pole Mount Bracket Machine Screws (Qty. 2) Installation Requirements • Pole-mounting: Two metal straps (not included) • Shielded Category 5 (or above) cabling with drain wire should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE.
Hardware Overview Ambient Light Sensor Camera Lens Microphone Reset Button RESET Camera Ring Ethernet Port RoHS Compliant M/N: UVC-G4-PRO 48V 0.5A PoE Tilt/Mount Ring Adjustable Base Cable Gland Mounting Base Cable Slot Reset Button The Reset button serves two functions: • Reboot Press and release the Reset button quickly. • Restore to Factory Defaults Press and hold the Reset button for 10-20 seconds while the camera is powered on. Release when LED turns off.
LED Ring LED Ring Color State Status White Solid Ready for configuration. Flashing Initializing. Heartbeat Flashing Device is being reset to factory defaults. Solid Indicates the device has been successfully adopted into a network and is working properly. Rotating Motion detected. Blue White/Blue Alternating Firmware upgrade in progress. Device is busy; do not touch or unplug it. Red Solid Device failure; network error. If this occurs, we recommend rebooting the device.
Before You Begin Remove the sticker from the bottom of the Mounting Base. Installation Overview To install the camera, please follow the instructions of the following sections in this order: 1. 2. 3. 4. Hardware Installation Connecting Power over Ethernet UniFi Protect Adjusting the Camera View Hardware Installation The camera can be mounted on a wall, ceiling, or pole. Follow the appropriate steps for your installation: Wall/Ceiling Mount 1.
2. Mark the mounting holes on the wall or ceiling. Note: If you are running the cable along the wall or ceiling, position the Cable Slot towards the direction you want the cabling to run. For outdoor installations, position the Cable Slot downward. 3. Use a 7 mm (¼") drill bit to drill the mounting holes in the wall or ceiling. Note: If you are running the Ethernet cable through the wall, cut a hole centered between the mounting holes that is large enough to feed the cable through. 4.
5. If you are feeding the Ethernet cable through the wall or ceiling, do so now and feed it through the Mounting Base. If not, feed the Ethernet cable through the Mounting Base and place the cable in the Cable Slot. IMPORTANT: If you are installing your camera outdoors, create a drip loop for the cable below the camera to prevent water ingress.
6. Fasten the Mounting Base to the wall or ceiling using two Self-Tapping Screws. 7. Remove the camera from the Adjustable Base by turning the Camera Ring in the direction shown. 8. Remove the Cable Gland from the Adjustable Base.
. Feed the Ethernet cable through the Cable Gland and Adjustable Base. Seal the Cable Gland in place by firmly pressing around its edges. Then connect the cable to the Ethernet Port on the camera. RESET RoHS Compliant M/N: UVC-G4-PRO 48V 0.5A PoE IMPORTANT: For proper weather sealing, the Cable Gland must fit securely within the Adjustable Base when the camera is mounted. Ensure that the Cable Gland is securely seated during installation and cable routing. 10.
11. Orient the camera to the desired position while connecting the Adjustable Base to the Mounting Base. Note: You will fine-tune and then lock the positioning after you check the camera view in the UniFi Protect software. 12. Proceed to the Connecting Power over Ethernet section. Pole Mount To mount the camera on a pole, use two metal straps (not included). 1. Feed the metal straps through the slots on the Pole Mount Bracket.
2. Wrap a metal strap around the pole and tighten it by turning the screw clockwise. Repeat for the second strap. 3. Remove the Mounting Base from the camera by turning the Tilt/Mount Ring counterclockwise. 4. Feed the Ethernet cable through the Mounting Base.
5. Fasten the Mounting Base to the Pole Mount Bracket using two Machine Screws. 6. Remove the camera from the Adjustable Base by turning the Camera Ring in the direction shown. 7. Remove the Cable Gland from the Adjustable Base.
8. Feed the Ethernet cable through the Cable Gland and Adjustable Base. Seal the Cable Gland in place by firmly pressing around its edges. Then connect the cable to the Ethernet Port on the camera. RESET RoHS Compliant M/N: UVC-G4-PRO 48V 0.5A PoE IMPORTANT: For proper weather sealing, the Cable Gland must fit securely within the Adjustable Base when the camera is mounted. Ensure that the Cable Gland is securely seated during installation and cable routing. 9.
10. Orient the camera to the desired position while connecting the Adjustable Base to the Mounting Base. Note: Fine-tune and then lock the positioning after you check the camera view in the UniFi Protect software.
Connecting Power over Ethernet The UVC G4 Pro supports 802.3af and 802.3at, and can be powered by any 802.3af/802.3at compliant switch, such as a UniFi PoE Switch. Connect the Ethernet cable from the camera directly to a PoE port on the switch.
UniFi Protect The UniFi Protect auto-management feature should automatically detect your new camera(s). To manage the camera: 1. Log in to UniFi Protect. Enter the username and password credentials used to set up the system and click Submit. 2. Click Add Cameras. Note: The green number icon on the Add Cameras button will display the number of cameras UniFi Protect has automatically detected.
3. Select the camera you would like to manage. You can rename the camera by typing into the box displaying the device. Click Add Selected Cameras. 4. The camera will appear on the Devices tab. The Camera Details window will be displayed on the right side of the screen. Check the camera view and proceed to the Adjusting the Camera View section.
UniFi Protect App Download the UniFi Protect app to add this camera to your UniFi Protect system. Note: When you first launch UniFi Protect, the app will prompt you to enable Bluetooth and other features necessary to provide the best user experience possible. Please allow these features and permissions for proper app functionality.
Adjusting the Camera View 1. Fine‑tune the positioning as you check the camera preview in the software. 2. Ensure that the arrow side of the included Tightening Tool faces the camera. Then insert the Tightening Tool between the camera and Adjustable Base. Arrow 3. Fit the Tightening Tool to the camera.
4. Turn the Tightening Tool to tighten the Camera Ring. 5. Move the Tightening Tool to fit the Tilt/Mount Ring. 6. Secure the Tilt/Mount Ring to lock the positioning and complete installation.
Specifications UVC-G4-PRO Dimensions Weight Enclosure Networking Interface Sensor Ø 86 x 153 mm (Ø 3.39 x 6.02") (Without Mounting Plate) 700 g (1.54 lb) (Without Mounting Plate) PC/TPE/Aluminum Alloy (ADC-12 + Liquid Coating) (1) 10/100/1000 Ethernet Port OS08A20, 1/1.8" Lens F 4.24mm - 12.66mm; f/1.53 -f/3.3 LED LED Ring Field of View Wide Tele Night Mode Video Compression Resolution Max. Frame Rate Image Settings Management Interface Managed Mode Standalone Mode Microphone Max.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: This product may become hot during operation. Exercise caution when handling. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI декларира, че това устройство UVC-G4-PRO е в съответствие със съществените изисквания и други приложими разпоредби на Директиви 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: ui.com/compliance Hrvatski [Croatian] UBIQUITI ovim putem izjavljuje da je ovaj uređaj UVC-G4-PRO sukladan osnovnim zahtjevima i ostalim bitnim odredbama Direktiva 2014/30/EU, 2014/35/EU.
Italiano [Italian] Con la presente, UBIQUITI, dichiara che questo dispositivo UVC-G4-PRO, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti delle direttive 2014/30/UE, 2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: ui.com/compliance Latviešu valoda [Latvian] Ar šo, UBIQUITI, deklarē, ka UVC-G4-PRO ierīce, ir saskaņā ar būtiskajām prasībām un citiem attiecīgiem noteikumiem Direktīvās 2014/30/ES, 2014/35/ES.
Ubiquiti Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA ©2018-2019 Ubiquiti Inc. All rights reserved. Ubiquiti, the Ubiquiti U logo, the Ubiquiti beam logo, UniFi, and UniFi Protect are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc, registered in the U.S. and other countries.
