080p Indoor/Outdoor IP Camera with Infrared and Optical Zoom Model: UVC-G3-PRO
Introduction Thank you for purchasing the Ubiquiti Networks® UniFi® Video G3 Pro Camera. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents UVC-G3-PRO Screw Anchors (Qty. 2) Tightening Tool Self-Tapping Screws (Qty. 2) 1080p Indoor/Outdoor IP Camera with Infrared and Optical Zoom Model: UVC-G3-PRO Pole Mount Bracket Machine Screws (Qty.
Installation Requirements • Pole-mounting: Two metal straps / hose clamps (not included) • Shielded Category 5 (or above) cabling with drain wire should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial‑grade, shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.
UVC-G3-PRO US-8-150W ETH-SP ETH-SP To LAN Diagram Showing Use of Ethernet Surge Protectors TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). Shielded Ethernet cable and earth grounding must be used for outdoor installations as conditions of product warranty. TOUGHCable™ is designed for outdoor installations. It is the professional installer’s responsibility to follow local country regulations.
Hardware Overview Ambient Light Sensor Camera Lens Microphone Reset Button Ethernet Port Camera Ring Tilt/Mount Ring Adjustable Base Cable Gland Mounting Base Cable Slot
Ethernet 10/100 RJ45 port connects to an 802.3af/802.3at or 24V Passive PoE switch for PoE power and data. Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the camera is powered on. Before You Begin Remove the sticker from the bottom of the Mounting Base. Installation Overview To install the camera, please follow the instructions of the following sections in this order: 1. 2. 3. 4.
Wall/Ceiling Mount 1. Remove the Mounting Base from the camera by turning the Tilt/Mount Ring counterclockwise. 2. Mark the mounting holes on the wall or ceiling.
Note: If you are running the cable along the wall or ceiling, position the Cable Slot towards the direction you want the cabling to run. For outdoor installations, position the Cable Slot downward. 3. Use a 7 mm (¼") drill bit to drill the mounting holes in the wall or ceiling. Note: If you are running the Ethernet cable through the wall, cut a hole centered between the mounting holes that is large enough to feed the cable through. 4. Insert a Screw Anchor into each mounting hole.
5. If you are feeding the Ethernet cable through the wall or ceiling, do so now and feed it through the Mounting Base. If not, feed the Ethernet cable through the Mounting Base and place the cable in the Cable Slot.
IMPORTANT: If you are installing your camera outdoors, create a drip loop for the cable below the camera to prevent water ingress. 6. Fasten the Mounting Base to the wall or ceiling using two Self-Tapping Screws. 7. Remove the camera from the Adjustable Base by turning the Camera Ring in the direction shown.
8. Remove the Cable Gland from the Adjustable Base. 9. Feed the Ethernet cable through the Cable Gland and Adjustable Base. Seal the Cable Gland in place by firmly pressing around its edges. Then connect the cable to the Ethernet Port on the camera.
IMPORTANT: For proper weather sealing, the Cable Gland must fit securely within the Adjustable Base when the camera is mounted. Ensure that the Cable Gland is securely seated during installation and cable routing. 10. Connect the camera back to the Adjustable Base by turning the Camera Ring in the direction shown.
11. Orient the camera to the desired position while connecting the Adjustable Base to the Mounting Base. Note: You will fine-tune and then lock the positioning after you check the camera view in the UniFi Video® software. 12. Proceed to the Connecting Power over Ethernet section.
Pole Mount To mount the camera on a pole, two metal straps are required (not included). 1. Feed the metal straps through the slots on the Pole Mount Bracket. 2. Wrap a metal strap around the pole and tighten it by turning the screw clockwise. Repeat for the second strap.
3. Remove the Mounting Base from the camera by turning the Tilt/Mount Ring counterclockwise. 4. Feed the Ethernet cable through the Mounting Base.
5. Fasten the Mounting Base to the Pole Mount Bracket using two Machine Screws. 6. Remove the camera from the Adjustable Base by turning the Camera Ring in the direction shown.
7. Remove the Cable Gland from the Adjustable Base. 8. Feed the Ethernet cable through the Cable Gland and Adjustable Base. Seal the Cable Gland in place by firmly pressing around its edges. Then connect the cable to the Ethernet Port on the camera.
IMPORTANT: For proper weather sealing, the Cable Gland must fit securely within the Adjustable Base when the camera is mounted. Ensure that the Cable Gland is securely seated during installation and cable routing. 9. Connect the camera back to the Adjustable Base by turning the Camera Ring in the direction shown.
10. Orient the camera to the desired position while connecting the Adjustable Base to the Mounting Base. Note: Fine-tune and then lock the positioning after you check the camera view in the UniFi Video software.
Connecting Power over Ethernet The UVC G3 Pro supports 802.3af, 802.3at, and 24V Passive PoE and can be powered by any 802.3af/802.3at or 24V Passive PoE compliant switch, such as a UniFi PoE Switch. Connect the Ethernet cable from the camera directly to a PoE port on the switch.
UniFi Video Ensure that you are running UniFi Video software version 3.9 or newer. The latest version of the UniFi Video software is available at www.ubnt.com/download/unifivideo The UniFi Video auto-management feature should automatically detect your new camera(s). To manage the camera: 1. Click the Unmanaged tab. 2. Select the camera row.
3. The Camera Details window will appear on the right side of the screen. Enter ubnt in the Username and Password fields and click Manage. 4. UniFi Video will automatically update the camera’s firmware (this may take up to five minutes). Then the camera will appear in the Managed cameras list. Check the camera view and proceed to the Adjusting the Camera View section.
UniFi Video App The UniFi Video app is available from the App Store® (iOS) or Google Play™ (Android). For details on using the UniFi Video software, refer to the User Guide at: www.ubnt.
Adjusting the Camera View 1. Fine‑tune the positioning as you check the camera preview in the software. 2. Ensure that the arrow side of the included Tightening Tool faces the camera. Then insert the Tightening Tool between the camera and Adjustable Base. Arrow 3. Fit the Tightening Tool to the camera.
4. Turn the Tightening Tool to tighten the Camera Ring. 5. Move the Tightening Tool to fit the Tilt/Mount Ring. 6. Secure the Tilt/Mount Ring to lock the positioning and complete installation.
Specifications UVC-G3-PRO Dimensions (Without Mounting Plate) Ø 86 x 153 mm (Ø 3.39 x 6.02") Weight (Without Mounting Plate) 700 g (1.54 lb) Enclosure Networking Interface Sensor Lens Field of View Wide Tele Night Mode Video Compression Resolution Maximum Frame Rate UV Stabilized Polycarbonate and Die-Cast Aluminum (1) 10/100 Ethernet Port Sony IMX290, 1/2.8" 3-9 mm, f/1.2-f/2.1 Powered Zoom Lens 108° (H), 58° (V), 125° (D) 37° (H), 20° (V), 43° (D) IR LEDs with Mechanical IR Cut Filter H.
Image Settings Management Interface Managed Mode Standalone Mode Microphone Max. Power Consumption Power Method Power Supply Buttons Mounting Operating Temperature Operating Humidity Weatherproofing Flip, Brightness, Contrast, WDR, Hue, Infrared, Sharpness, Saturation, Denoise, 50/60 Hz Flicker Reduction UniFi Video v3.9 or Newer Camera Integrated Web UI Yes 12.5W IEEE 802.3af/at Type 2 PoE or 24V Passive PoE 802.3af/802.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: This product may become hot during operation. Exercise caution when handling. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
Limited Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation.
In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation; all Ethernet cabling runs use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is used, and for indoor installations, indoor cabling requirements are followed.
AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES.
Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you.
reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben. Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados.
bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit où vous avez acheté le produit.
Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че това устройство UVC-G3-PRO е в съответствие със съществените изисквания и други приложими разпоредби на Директиви 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.ubnt.
Suomi [Finnish] Täten UBIQUITI NETWORKS vakuuttaa, että tämä UVC-G3-PRO laite, on yhdenmukainen olennaisten vaatimusten ja muiden sitä koskevien direktiivien 2014/30/EU, 2014/35/EU. EU‑vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: www.ubnt.
Latviešu valoda [Latvian] Ar šo, UBIQUITI NETWORKS, deklarē, ka UVC-G3-PRO ierīce, ir saskaņā ar būtiskajām prasībām un citiem attiecīgiem noteikumiem Direktīvās 2014/30/ES, 2014/35/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: www.ubnt.com/compliance Lietuvių kalba [Lithuanian] UBIQUITI NETWORKS deklaruoja, kad šis UVC-G3-PRO įrenginys atitinka esminius reikalavimus ir kitas 2014/30/ES, 2014/35/ES Direktyvų nuostatas.
Slovenščina [Slovenian] Družba UBIQUITI NETWORKS izjavlja, da je naprava UVC-G3-PRO v skladu z obveznimi zahtevami in drugimi ustreznimi določbami direktiv 2014/30/EU in 2014/35/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: www.ubnt.
