G Managed PoE+ Gigabit Switch with SFP Models: US-24-250W, US-24-500W
Introduction Thank you for purchasing the Ubiquiti Networks® UniFi® Switch with SFP. The UniFi Controller software and User Guide are available for download at: downloads.ubnt.com/unifi This Quick Start Guide is designed to guide you through the installation and show you how to access the Configuration Interface. This Quick Start Guide also includes the warranty terms, and is for use with the UniFi Switch with SFP, model US‑24-250W or US-24-500W.
Network Topology Requirements • A DHCP-enabled network for the UniFi Switch to obtain an IP address (connected devices will also obtain IP addresses after deployment) • A management station running the UniFi Controller software, located either on-site and connected to the same Layer 2 network, or off-site in a cloud or NOC UAP-AC CURRENT SITE UAP-PRO UAP-Outdoor+ REFRESH RATE Default 2 minutes Network Health DASHBOARD MAP DEVICES CLIENTS CALLS STATISTICS INSIGHTS WLAN www WAN LAN VOIP www WAN
Hardware Overview Front Panel System LED System State Status White Factory defaults, waiting for integration. Flashing White Initializing. Alternating White/Blue Device is busy; do not use or unplug it. This usually indicates that a process such as a firmware upgrade is taking place. Blue Successfully integrated into a network and working properly. This is used to locate a device. Flashing Blue When you click Locate in the UniFi Controller software, the System LED will flash blue.
Front Panel Port LEDs RJ45: PoE RJ45: Speed/Link/Act SFP: Speed/Link/Act 1G LED RJ45 1-24 PoE State Status Off No PoE Amber IEEE 802.3af/802.
Front Panel Ports SFP 1-2 RJ45 1-24 1G Port RJ45 1-24 SFP 1-2 Description RJ45 ports support Power over Ethernet (PoE) and 10/100/1000 Ethernet connections. Hot-swappable SFP ports support 1 Gbps connections. Front Panel Button 1G Reset Button Description This button serves two functions for the UniFi Switch: Reset • Restart Press and release the Reset button quickly. • Restore to Factory Default Settings Press and hold the Reset button for more than five seconds.
Back Panel Mounting Holes Mounting Holes CONSOLE Console Port Console Power Description RJ45 serial console port for Command Line Interface (CLI) management. Use an RJ45‑to-DB9, serial console cable, also known as a rollover cable, to connect the Console port to your computer. Then configure the following settings as needed: • Baud rate 115200 • Data bits 8 • Parity NONE • Stop bits 1 • Flow control NONE Note: There are fans and ventilation holes on the sides of the UniFi Switch.
Hardware Installation 1. Connect the Power Cord to the Power port of the UniFi Switch. 2. Attach the UniFi Switch to the rack using the four Mounting Screws. (If the rack has square slots, then use the Cage Nuts with the Mounting Screws.) 1 3 5 7 2 9 4 11 6 13 8 15 10 17 12 19 14 21 16 22 18 20 SFP 1 22 24 SFP 2 Note: Keep 20 mm of clearance next to the ventilation holes for adequate airflow.
3. Connect the other end of the Power Cord to a power outlet. Connecting Ethernet 1. Connect an Ethernet cable from your computer or host system to any port of UniFi Switch. 1 3 5 7 2 9 4 11 6 13 8 15 10 17 12 19 14 21 16 22 18 20 SFP 1 22 24 SFP 2 2. Connect Ethernet cables from the Ethernet ports of your devices to the other numbered ports of the UniFi Switch. Note: The PoE settings for ports 1-24 are set to auto-sensing PoE+ by default, so 802.
Using SFP Ports To use an SFP port: 1 1. Remove the protective plug covering the SFP port. 2. Plug a compatible fiber module into the SFP port. 3 5 7 2 9 4 11 6 13 8 15 10 17 12 19 14 21 16 22 18 20 SF P1 22 24 SF P2 DDM 20KM m SC 310n s SM/ /Rx1 Mbp 1000 50nm Tx15 1 3 3. Connect a fiber optic cable to the fiber module. Then connect the other end of the cable to another fiber device.
Software Installation Download and install the latest version of the UniFi Controller software at downloads.ubnt.com/unifi and follow the on‑screen instructions. Note: If you already have UniFi Controller v4.3.x or higher installed, skip to the section, Adopting the UniFi Switch. After you have installed the software and run the UniFi Installation Wizard, a login screen will appear for the UniFi Controller management interface. Enter the admin name and password that you created and click Login.
Adopting the UniFi Switch 1. From the UniFi Controller dashboard, click DEVICES in the left menu bar. 2. On the Devices screen, locate the UniFi Switch in the list of devices under the Name/MAC Address column. To adopt the UniFi Switch, click ADOPT. 3. The System LED on the UniFi Switch will turn blue to confirm that it has been successfully adopted. To configure PoE settings, proceed to the Configuring PoE Settings section.
Configuring PoE Settings The PoE settings for ports 1-24 are set to auto-sensing PoE+ by default, so 802.3af/at devices can be plugged in and automatically receive PoE. WARNING: Before activating 24V passive PoE, ensure that the connected device supports PoE and the supplied voltage. 1. On the Devices screen, locate the UniFi Switch in the list of devices under the Name/MAC Address column. Double-click its Name/MAC Address to access its settings. 2. Click the Ports tab.
3. Click Actions for the port you want to configure. 4. Select the appropriate mode: Off, 24V Passive, or PoE+ from the PoE setting. Then click Apply. For more information, refer to the User Guide on the website: documentation.ubnt.
Specifications UniFi Switch Dimensions 485 x 43.7 x 285.4 mm (19.09 x 1.72 x 11.24") Weight US-24-250W US-24-500W 4.7 kg (10.4 lb) 4.8 kg (10.6 lb) Total Non-Blocking Line Rate 26 Gbps Max.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
Limited Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation.
Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PUR
Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you.
Australia and New Zealand Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it.
Español La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity Česky [Czech] UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI NETWORKS device, je ve shod se základními po adavky a dal ími p íslu n mi ustanoveními sm rnice 1999/5/ES. Dansk [Danish] Undertegnede UBIQUITI NETWORKS erklærer herved, at følgende udstyr UBIQUITI NETWORKS device, overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Italiano [Italian] Con la presente UBIQUITI NETWORKS dichiara che questo UBIQUITI NETWORKS device, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem.
www.ubnt.com ©2014 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, TOUGHCable, and UniFi are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their respective owners.
