GPON CPE Model: UF-LOCO
Introduction Thank you for purchasing the Ubiquiti Networks® U Fiber loco. This Quick Start Guide is designed to guide you through the installation and also includes the warranty terms. Package Contents U Fiber loco Wall Mount Bracket Screws (Qty. 4) GPON CPE Model: UF-LOCO Screw Anchors (Qty. 4) Micro-USB Power Adapter* (5V, 1A) Quick Start Guide * Included only in the single-pack of the UF-LOCO.
Hardware Overview Reset Button The Reset button serves two functions for the UF-LOCO: • Restart Press and release the Reset button quickly. The three signal LEDs will flash amber. • Restore to Factory Default Settings Press and hold the Reset button for more than five seconds. The three signal LEDs will light amber in this sequence with a 100-ms delay between patterns: Ports Port Description PON SC/APC GPON port supports WAN connections of 2.488 Gbps downstream and 1.244 Gbps upstream.
LEDs Ethernet Signal Power Ethernet LED LED State Status Off Ethernet connection down White Ethernet connection up Power LED LED State Status Off Power off White Power on
Signal LEDs LED State Status Off Bootup (1) White (2) White (3) White Signal strength: low ≥ -28 dBm Signal strength: good ≥ -25 dBm Signal strength: strong ≥ -11 dBm Signal strength: too low < -28 dBm (1) Amber Check the quality of the fiber connection, and calculate the total optical loss of the optical splitters. Signal strength: too strong (1) Amber (2) White ≥ -8 dBm Add an optical splitter, or add a 5 or 10 dB optical attenuator.
Hardware Installation The UF-LOCO can be mounted on a wall or placed on a desktop. WARNING: To reduce the risk of fire or electric shock, do not expose the UF-LOCO to rain or moisture. Wall Mounting 1. Use the Wall Mount Bracket as a template and drill four 6 mm holes as shown below. 40 mm 40 mm 2. Insert a Screw Anchor into each hole, and then fasten the Wall Mount Bracket using four Screws.
3. Mount the UF-LOCO by inserting the top of the UF-LOCO into the Mount Bracket and then pivot the bottom into the bracket until it locks into place.
Connecting Fiber Connect the fiber optic cable from the Passive Optical Network to the PON port.
Connecting LAN 1. Connect an Ethernet cable to the LAN port. 2. If you are using PoE, go to Connecting Power. If you are using the Micro-USB Power Adapter, connect the other end of the Ethernet cable to your LAN.
Connecting Power Connect the power using one of the following options: • Using the Micro-USB Power Adapter: Go to Connecting to the Micro-USB Power Adapter. • Using an airCube™ (not included): Go to Connecting to the airCube. Note: The airCube provides Wi-Fi connectivity with PoE passthrough, so it is the ideal complement to the UF-LOCO for CPE installations. • Using a PoE switch (not included): Connect the Ethernet cable from the UF-LOCO to a PoE-enabled Ethernet port on the switch.
Connecting to the airCube 1. Connect the Ethernet cable from the UF-LOCO to the WAN 24V PoE OUT port on the back of the airCube (not included). 2. To power the airCube, follow the instructions in its Quick Start Guide.
Accessing the Configuration Interface 1. Ensure that your computer (or other host system) is connected to the UF-LOCO. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet. 3. Launch your web browser. Type http://192.168.1.1 in the address field. Press enter (PC) or return (Mac). http://192.168.1.1 4. The login screen will appear. Enter ubnt in the Username and Password fields. Click Login. The U Fiber Configuration Interface will appear.
OLT Compatibility Profiles The UF-LOCO is compatible with most major brands of OLT (Optical Line Terminal) and offers four compatibility profiles. By default the UF-LOCO is set to Profile 1 - Ubiquiti Networks U Fiber OLT. For other brands, manually select Profile 2, 3, or 4. 1. Log into the U Fiber Configuration Interface. 2. The Dashboard screen will appear. Click the Settings 3. On the Network screen, click the System tab. tab.
4. Select the appropriate profile from the OLT Profile drop‑down menu: • Profile 1 Ubiquiti Networks U Fiber OLT • Profile 2 Other brands • Profile 3 Other brands • Profile 4 Other brands Note: For more information, visit: https://ubnt.link/Supported-3rd-Party-OLTs 5. Click Save Changes. The UF-LOCO will automatically restart with the new profile.
Specifications UF-LOCO Dimensions 76.5 x 76.5 x 26.4 mm (3.01 x 3.01 x 1.04") Weight 77 g (2.72 oz) Networking Interfaces (1) SC/APC, GPON WAN (1) RJ45, Ethernet LAN Networking Interface Speeds (1) GPON WAN, ITU G.984, 2.488 Gbps Downstream, 1.244 Gbps Upstream (1) GbE LAN, 10/100/1000 Mbps Management Interface In-Band Ethernet PON Normal Optical Power Range TX (Class B+): 1.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. WARNING: CLASS 1 LASER PRODUCT - Do not look into the ends of the fiber optic cable or SFP modules while converters are powered.
(III) (IV) has been damaged due to errors or defects in cabling; has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical stress, including lightning strikes, or accident; (V) has been damaged or impaired as a result of using third party firmware; (VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or (VII) has not been received by Ubiquiti within 30 days of issuance of the RMA.
PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the operation of the Products will be error-free or that operation will be uninterrupted.
Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че това устройство UF-LOCO е в съответствие със съществените изисквания и други приложими разпоредби на Директиви 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.ubnt.
Italiano [Italian] Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo UF-LOCO, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti delle direttive 2014/30/UE, 2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.ubnt.
www.ubnt.com Ubiquiti Networks, Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA ©2017-2018 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airCube, and U Fiber are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their respective owners.
