In-Wall Wi-Fi Access Point Model: UAP-IW
Introduction Thank you for purchasing the Ubiquiti Networks® UniFi® In‑Wall Wi-Fi Access Point. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Important: The UAP-IW requires the UniFi Controller v4.7 or higher, available at: downloads.ubnt.com/unifi Package Contents In-Wall 802.
Network Topology Requirements • A DHCP-enabled network (for the AP to obtain an IP address as well as for the wireless clients after deployment) • A management station running the UniFi Controller software, located either on-site and connected to the same Layer-2 network, or off-site in a cloud or NOC UAP-IW UAP-AC-PRO UAP-AC Outdoor CURRENT SITE REFRESH RATE Default 2 minutes Network Health DASHBOARD MAP DEVICES CLIENTS CALLS STATISTICS INSIGHTS WLAN www WAN LAN VOIP www WAN IP XXX.XXX.
Hardware Overview PoE Out + Data Data Reset PoE In + Data PoE Out + Data 10/100 Ethernet port supports data and PoE. Used to connect an 802.3af device to the LAN. Data 10/100 Ethernet port supports data only. Used to connect a client device to the LAN. PoE In + Data 10/100 Ethernet port supports data and PoE. Connect this port to the LAN and DHCP server via an 802.3af switch. Reset The Reset button serves two functions for the UAP-IW: • Restart Press and release the Reset button quickly.
LED LED LED Color Status White Factory default, waiting to be integrated. Flashing White Initializing. Alternating White/Blue Device is busy; do not touch or unplug it. This usually indicates that a process such as a firmware upgrade is taking place. Blue Indicates the device has been successfully integrated into a network and is working properly. This is used to locate an AP. Quickly Flashing Blue When you click Locate in the UniFi Controller software, the AP will flash.
Hardware Installation An electrical wall box should be pre-installed with an Ethernet cable running from the box to an 802.3af switch. 1. Detach the Cover Plate from the UAP-IW. 2. Connect the Ethernet cable in the wall box to the port labeled PoE IN + DATA.
3. Place the UAP-IW in the wall box and properly position the cable to ensure the Ethernet connection is not strained. Note: If the wall box does not have enough room to accommodate the UAP-IW without straining the Ethernet connection, replace the wall box with an open‑end or deeper box.
4. Fasten the top and bottom screws. Adjust the screws to ensure the mounting plate is flush with the wall for proper fitting of the Cover Plate. Note: Do not over-tighten or rely on the force of the screws to pull the UAP-IW into the wall box.
5. Attach the Cover Plate. Press the Cover Plate into position until the four mounting clips snap into place. If you are using your own cover plate, secure it with two screws.
Software Installation Download and install the latest version of the UniFi Controller software at: downloads.ubnt.com/unifi Launch the software and follow the on-screen instructions. Step-by-step instructions are available in the User Guide located on our website: documentation.ubnt.com/unifi After you have installed the software and run the UniFi Installation Wizard, a login screen will appear for the UniFi Controller management interface. Enter the Admin Name and Password that you created and click Login.
Specifications UAP-IW Dimensions Weight Networking Interface Button Operating Band Antenna Gain Max. Data Speed Max. Range 114.6 x 70.6 x 28.5 mm (4.51 x 2.78 x 1.12") 117 g (4.127 oz) (3) 10/100 Ethernet Ports Reset 2.4 GHz 1 dBi 150 Mbps 25 m (82') Wi-Fi Standards 802.11 b/g/n Power Method PoE 802.3af Max. Power Consumption Max.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label.
Limited Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation.
Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PUR
Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you.
Industry Canada CAN ICES-3(A)/NMB-3(A) This Class A digital apparatus complies with Canadian ICES-003. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2.
CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
Español La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity Česky [Czech] UBIQUITI NETWORKS tímto prohlašuje, že toto UBIQUITI NETWORKS zařízení, je ve shod se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Hermed, UBIQUITI NETWORKS, erklærer at denne UBIQUITI NETWORKS enhed, er i overensstemmelse med de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Malti [Maltese] Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan il-mezz UBIQUITI NETWORKS huwa konformi mar-rekwiżiti essenzjali u dispożizzjonijiet rilevanti oħrajn ta ‘Direttiva 1999/5/EC. Norsk [Norwegian] Herved UBIQUITI NETWORKS, erklærer at denne UBIQUITI NETWORKS enheten, er i samsvar med de grunnleggende kravene og andre relevante bestemmelser i direktiv 1999/5/EF.
