802.
• • • • • • • • • • • • Package Contents Hardware Overview Installation Powering the UAP-FlexHD Software Installation Mobile App Installation Specifications Safety Notices Electrical Safety Information Limited Warranty Compliance Declaration of Conformity
Package Contents UniFi AP FlexHD Base Mount Outdoor Mount PoE Adapter* (48V, 0.32A) Power Cord Security Screw * Wall/Pole Mount Plastic Ties (Qty. 2) Screws (Qty. 3) Screw Anchors (Qty. 3) Included only in the single-pack of the UAP-FlexHD Installation Requirements • Phillips screwdriver • Cat5/6 UTP cable for indoor installations • Shielded Category 5 (or above) cabling should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE.
Hardware Overview LED 1 LED Color Status White Factory default, waiting to be integrated. Flashing White Initializing. Alternating White/Blue Device is busy; do not touch or unplug it. This usually indicates that a process such as a firmware upgrade is taking place. Blue Indicates the device has been successfully integrated into a network and is working properly. This is used to locate an AP. Quickly Flashing Blue When you click Locate in the UniFi Controller software, the AP will flash.
Ports 2 3 Ethernet Gigabit Ethernet port used to connect 802.3af PoE power and should be connected to the LAN and DHCP server. Reset The Reset button serves two functions for the UniFi AP: • Restart Press and release the Reset button quickly. • Restore to Factory Default Settings Press and hold the Reset button for more than five seconds.
Installation Determine the installation location of the UAP FlexHD: • • • • Desktop For installing on a flat surface such as a desktop or table/shelf; could be set up for temporary installations. Wall For installing in a secure location; used more for stationary or permanent installations. Ceiling For installing in a ceiling tile using the optional recessed ceiling mount assembly (sold separately). Pole For installing on a pole (indoor or outdoor).
Desktop 1. Remove the Base Mount from the UAP FlexHD.
2. Connect an Ethernet cable to the Ethernet Port in the base of the UAP FlexHD. 3. Reattach the Base Mount to the UAP FlexHD. 4. Orient the UAP FlexHD in the upright position and place on a flat surface for installation.
Wall If the Ethernet cable is coming from the inside of a wall: 1. Bend and remove the plastic tab that covers the cable feed. 2. Use the Wall Mount as a template to mark the holes on the wall where the UAP FlexHD will be installed. 3. Pre-drill the holes in the wall and pull the Ethernet cable forward, sliding it through the opening in the Wall Mount. Then use the Screws and Screw Anchors to secure the Wall Mount to the wall.
4. Connect the Ethernet cable to the Ethernet Port and slide the UAP FlexHD onto the wall mount. Note: If you are mounting the UAP-FlexHD outside or near the outdoors, attach the Outdoor Mount prior to attaching the UAP FlexHD to the Wall Mount.
Installation complete.
Ceiling (Optional Accessory) Use the optional Ceiling Mount, Mount Cover, and Back Plate Assembly to install the UAP FlexHD on a drop tile ceiling or horizontal surface where the interior side of the Ceiling Mount is accessible. 1. Use the base of the Ceiling Mount as a template to mark the diameter of the hole where the UAP FlexHD will be installed. Then, cut along the marked line to make a hole in the ceiling tile. 2.
3. Pass the Ethernet cable through the Ceiling Mount and connect it to the Ethernet port on the UAP FlexHD. 4. Slide the UAP FlexHD all the way up into the Ceiling Mount until it snaps into place. Then, attach the magnetic cover to the base of the ceiling mount. Installation complete.
Pole Note: If you are mounting the UAP-FlexHD outdoors, it must be installed in the upright position to prevent water from getting into the base of the device. 1. Attach the Pole Mount to a pole using the included Zip Ties. 2. Slide the Ethernet cable through the opening in the Outdoor Mount and connect the Ethernet cable to the Ethernet Port.
3. Attach the Outdoor Mount to the UAP FlexHD. 4. Slide the UAP FlexHD onto the Pole Mount.
5. Use a phillips screwdriver to install the Security Screw through the Outdoor Mount and into the base of the UAP FlexHD. This secures the device to the pole mount. Installation complete.
Powering the UAP-FlexHD The UAP-FlexHD features auto-sensing 802.3af PoE support and can be powered by any of the following: • Ubiquiti UniFi Switch with 802.3af PoE support • Ubiquiti Gigabit PoE Adapter (48V, 0.32A) (included) Connecting to an 802.3af PoE Switch Connect the Ethernet cable from the UAP-FlexHD directly to an 802.3af PoE port on the switch.
Connecting to a PoE Adapter 1. Connect the Ethernet cable from the UAP-FlexHD to the POE port of the Gigabit PoE adapter. 2. Connect an Ethernet cable from your LAN to the LAN port of the Gigabit PoE adapter. 3. Connect the Power Cord to the adapter, and then plug the Power Cord into a power outlet. Mounting the PoE Adapter (Optional) 1. Remove the PoE Mounting Bracket from the adapter, place the bracket at the desired location, and mark the two holes. 2.
Software Installation Download and install the latest version of the UniFi Controller software. Launch it and follow the on-screen instructions. The software and step-by-step instructions in the User Guide are available at: ui.com/download/unifi After you install the UniFi Controller software and run the installation wizard, you will be prompted for the credentials to log into UniFi Controller. Enter the username and password you created and click Sign In.
Specifications UAP-FlexHD Dimensions Weight Networking Interface Button LED Power Method Power Supply Ø 48.50 x 159.49 mm (1.90 x 6.28") 315 g (0.69 lb) (1) 10/100/1000 Ethernet Port Reset White / Blue 802.3af 802.3af 48V, 0.32A Gigabit PoE Adapter Max. Power Consumption 10.5W Supported Voltage Range 44 - 57VDC Operating Frequency Max. TX Power 2.4 GHz 5 GHz Throughput 2.4 GHz 5 GHz Antenna Gain 2.4 GHz 5 GHz Wi-Fi Standards Wireless Security Mounting 2.4 GHz 5 GHz 23 dBm 26 dBm 300 Mbps 1733 Mbps 1.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
Limited Warranty www.ui.com/support/warranty The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
CAN ICES-3(A)/NMB-3(A) Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. 2. l’appareil ne doit pas produire de brouillage; l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Le présent émetteur radio (IC : 6545A-UAPFLEXHD) a été approuvé par ISDE Canada.
Australia and New Zealand Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Brazil Nota: Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it.
RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI декларира, че този тип радиосъоръжение UAP-FlexHD е в съответствие с Директива 2014/53/EU, 2014/30/EU & 2014/35/EU. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.ui.com/compliance Hrvatski [Croatian] UBIQUITI ovime izjavljuje da je radijska oprema tipa UAP-FlexHD u skladu s Direktivom 2014/53/EU, 2014/30/EU & 2014/35/EU.
Latviešu valoda [Latvian] Ar šo UBIQUITI deklarē, ka radioiekārta UAP-FlexHD atbilst Direktīvai 2014/53/ES, 2014/30/ES & 2014/35/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē:www.ui.com/compliance Lietuvių kalba [Lithuanian] Aš, UBIQUITI, patvirtinu, kad radijo įrenginių tipas UAP-FlexHD atitinka Direktyvą 2014/53/ES, 2014/30/ES & 2014/35/ES. Visas ES atitikties deklaracijos tekstas prieinamas šiuo interneto adresu: www.ui.
Online Resources Support help.ui.com Community community.ui.com Downloads downloads.ui.com Ubiquiti Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA www.ui.com ©2019 Ubiquiti Inc. All rights reserved. Ubiquiti, the Ubiquiti U logo, the Ubiquiti beam logo, TOUGHCable, and UniFi are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries.
