Owners manual

37
UniFi® Controller User Guide
Ubiquiti Networks, Inc.
Chapter 5: Devices
Status Displays the connection status.
• Connected The AP is physically wired to the network.
• Connected (wireless) The AP is wirelessly uplinked to a
physically wired AP.
• Disconnected The AP is unreachable by the UniFi
Controller software.
• Isolated A managed AP is unable to locate itsuplink.
• Managed by Other The AP is not in the default state
but it is not controlled by the UniFi Controller.
• Pending Approval The AP is in the default state and is
available for adoption.
2G Clients Displays the number of clients connected to
the AP using the 2.4 GHz band.
5G Clients Displays the number of clients connected to
the AP using the 5 GHz band.
TX Displays the overall TX (transmit) rate.
RX Displays the overall RX (receive) rate.
TX 2G Displays the overall TX rate for the 2.4 GHz radio
band. The different colors represent different types of
packet activity:
Color Packet Activity
Packets sent
Packets retried
Packets not sent due to likely interference
TX 5G Displays the overall TX rate for the 5 GHz radio
band. The different colors represent different types of
packet activity:
Color Packet Activity
Packets sent
Packets retried
Packets not sent due to likely interference
Channel Displays the transmit/receive channel being
used by the AP. The radio band is represented as (ng) for
2.4 GHz and (na)/(ac) for 5 GHz.
Actions Click a button to perform the desired action:
• Locate Click
to flash the LED on the AP and the
AP’s icon on the Map tab so you can locate it. The LED
will flash until the Locate button is clicked again. (The
icon on the Map tab will flash three times and stop.)
• Restart Click
to restart the selected device.
• Upgrade If a software upgrade is available for the
device, click to install the latest UniFi firmware
on the device. The Status will appear as Upgrading until
the process is complete and the device reconnects to
the UniFi Controller software.
• Adopt Click
to adopt a device that appears as
Pending Approval for its status. The Status will appear as
Adopting until the device is connected.
Phones
VoIP is available with UniFi Controller version 4.6 or higher.
Upgrade All Click to begin automatically
upgrading the firmware of all Phones.
(icon) Displays the icon corresponding to the Phone (not
all icons are shown below):
UniFi VoIP Phone/Pro
UniFi VoIP Phone Executive
Name/MAC Address Displays the hostname, alias, or
MAC address of the Phone. You can click the name to get
additional details; see “UniFi VoIP Phone Details” on
page 77 for more information.
IP Address Displays the IP address used by the Phone.
Status Indicates the device status: Connected,
Disconnected, Pending Approval, Adopting, Upgrading, or
Managed by Other.
Extension Displays the extension of the Phone. You
can click the extension to get additional details; see
“Add Click this option to set up a new number. The
Ceate New Number screen appears:” on page 17 for
more information.
Num Calls Displays the total number of incoming and
outgoing calls for the Phone.
Minutes Displays the total number of call minutes used
by the Phone.
Actions Click a button to perform the desired action:
• Locate Click
to ring the Phone and flash the
Phone’s icon on the Map tab so you can locate it. (The
Phone will ring three times and stop; the icon on the
Map tab will flash three times and stop.)
• Restart Click to restart the selected device.
• Upgrade If a software upgrade is available for the
device, click to install the latest UniFi firmware
on the device. The Status will appear as Upgrading until
the process is complete and the device reconnects to
the UniFi Controller software.
• Adopt Click to adopt a device that appears as
Pending Approval for its status. The Status will appear as
Adopting until the device is connected.