Rackmount Power over Ethernet Managed Switches Model: TS-16-CARRIER
Introduction Introduction Thank you for purchasing the Ubiquiti Networks™ TOUGHSwitch™ PoE CARRIER, which is part of the TOUGHSwitch series: Name Model Description TOUGHSwitch PoE TS-5-POE 5-port managed switch featuring 24V PoE TOUGHSwitch PoE PRO TS-8-PRO 8-port managed switch featuring 24V/48V PoE TOUGHSwitch PoE CARRIER TS-16-CARRIER Two TOUGHSwitch PoE PROs mounted in a rack This Quick Start Guide is designed to guide you through the installation and show you how to access the Configuratio
TOUGHSwitch™ PoE CARRIER Quick Start Guide Hardware Overview A and B designate the two 8-Port TOUGHSwitch PoE PROs housed in the rack. This may be useful for the Location setting on the Device tab in the Configuration Interface. Back Panel TOUGHSwitch B Ventilation Holes Mounting Screws TOUGHSwitch A Power Ventilation Holes Power Mounting Screws Note: There are additional ventilation holes on the top and sides of each TOUGHSwitch.
Hardware Overview Front Panel LEDs Power/Link Speed/Link/Act PoE Management LED Power/ Link 1-8 PoE Speed/ Link/Act State Status Off No Power/No Link Amber After bootup, the LED indicates power. After an initial link is established, the LED indicates a 10/100 Mbps connection. If the link terminates, the LED turns off until a link is re-established. If the unit reboots, the LED will again indicate power until a link is established.
TOUGHSwitch™ PoE CARRIER Quick Start Guide Installation Requirements • Phillips and flathead screwdrivers • Standard-sized, 19" wide rack with a minimum of 1U height available • For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use. • For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply.
Hardware Installation 2. Attach the TOUGHSwitch PoE CARRIER to the rack using the four #10-32 x 5/8" Phillips Screws. (If the rack has square slots, then use the #10-32 x 5/8" Cage Nuts with the Phillips Screws.) Note: Keep 20 mm of clearance next to the ventilation holes for adequate airflow. 3. Attach the top portion of the faceplate at a slight angle, and then snap on the bottom portion. Secure the faceplate to the TOUGHSwitch PoE CARRIER using the two M3x8 Flathead Screws.
TOUGHSwitch™ PoE CARRIER Quick Start Guide 4. Connect the other end of each Power Cord to a power outlet. Connecting Ethernet 1. Connect an Ethernet cable from your computer or host system to the Management port of TOUGHSwitch A. Note: By default, you can configure the TOUGHSwitch via any port; however, we recommend the Management port. (Access to the Configuration Interface can be limited to the Management port only. You can configure this setting on the Device tab.
Daisy-Chain (Optional) 2. Connect Ethernet cables from the Ethernet ports of your devices to the numbered ports of each TOUGHSwitch. Note: PoE is disabled by default on all numbered ports and is not available on the Management port. To enable PoE, use the Ports tab in the Configuration Interface. Daisy-Chain (Optional) All data ports are available as uplink ports.
TOUGHSwitch™ PoE CARRIER Quick Start Guide Accessing the Configuration Interface ToughSwitch A and B have the same default IP address, 192.168.1.20, so you will need to change the IP address of at least one TOUGHSwitch. Follow the instructions in this section to configure one TOUGHSwitch at a time, starting with TOUGHSwitch A. 1. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet (e.g., 192.168.1.100). 2. Launch your web browser. Type https://192.168.1.
Accessing the Configuration Interface 4. Change the Static Management IP Address to a unique IP address on the Device tab. Click Save Changes. 5. You can enable PoE on the Ports tab and customize additional settings as needed. 6. Disconnect the Ethernet cable from the Management port of TOUGHSwitch A and connect it to the Management port of TOUGHSwitch B. Then repeat steps 1-5 on TOUGHSwitch B. Refer to the TOUGHSwitch PoE User Guide for instructions on configuring the TOUGHSwitch.
TOUGHSwitch™ PoE CARRIER Quick Start Guide Specifications 8-Port TOUGHSwitch PoE PRO* Power Input 110-120VAC / 210-230VAC Max. Power Consumption 150 W PoE Out Voltage Range 45-48VDC / 22-24VDC Max. PoE Wattage Per Gigabit Port 11.5 W (24 V), 23 W (48V) ESD Rating 24 kV Air / 24 kV Contact PoE Method Passive Button Reset USB Port 2.
Safety Notices Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
TOUGHSwitch™ PoE CARRIER Quick Start Guide Warranty Conditions The above warranty does not apply if the Product: (I) has been modified and/or altered, or an addition made thereto, except by Ubiquiti Networks, or Ubiquiti Networks’ authorized representatives, or as approved by Ubiquiti Networks in writing; (II) has been painted, rebranded or physically modified in any way; (III) has been damaged due to errors or defects in cabling; (IV) has been subjected to misuse, abuse, negligence, abnormal physical, ele
Compliance Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
TOUGHSwitch™ PoE CARRIER Quick Start Guide CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
Declaration of Conformity de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique.
TOUGHSwitch™ PoE CARRIER Quick Start Guide Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ UBIQUITI NETWORKS ΔΗΛΩΝΕΙ ΟΤΙ UBIQUITI NETWORKS device, ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1995/5/ΕΚ. Magyar [Hungarian] Alulírott, UBIQUITI NETWORKS nyilatkozom, hogy a UBIQUITI NETWORKS device, megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Support support.ubnt.com Community community.ubnt.com Downloads downloads.ubnt.com www.ubnt.com © 2012-2013 Ubiquiti Networks, Inc. All rights reserved.
