Shielded airMAX® ac Radio with Isolation Antenna and airPrism® Technology Model: PS-5AC
Introduction Thank you for purchasing the Ubiquiti Networks® PrismStation™ AC. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents PrismStation AC Pole Clamp GPS Antenna Carriage Bolts (Qty. 2) Metal Strap Flange Nuts (Qty. 2) Mounting Bracket Allen Wrench Shielded airMAX® ac Radio with Isolation Antenna and airPrism® Technology Model: PS-5AC Gigabit PoE (24V, 0.
Hardware Overview Power LED Reset Button GPS Antenna Connector Ethernet Port GPS Antenna Connector This is used to connect the included GPS Antenna. Power LED The LED will light blue when the device is connected to a power source. Ethernet Port This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server. Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the PrismStation is powered on.
Release Button Release Button Release Button The default horn (beamwidth: 45°) can be swapped out for an optional horn with a different beamwidth. To remove the attached horn, rotate the horn counterclockwise while depressing the Release Button. To reinstall the horn, align the arrow on the horn with the Release Button. Then press down on the horn and rotate it clockwise until you hear a click.
Hardware Installation There are two pole-mounting methods; follow the appropriate instructions for your selection. Metal Strap Use this option for quick mounting on a pole. Mounting Bracket Use this option for elevation adjustments. Metal Strap 1. Open the Metal Strap and feed it through the base of the PrismStation. 2. Wrap the Metal Strap around the pole. Use a 7 mm socket wrench to turn the screw clockwise and securely fasten the clamp to the pole. 3.
Mounting Bracket 1. Attach the Pole Clamp to the Mounting Bracket. a. Hold the Mounting Bracket with its clamps facing you and the head of the Tightening Bolt facing upward. b. Insert the two Carriage Bolts through the holes of the Mounting Bracket. c. Slide the hole of the Pole Clamp over one bolt of the Mounting Bracket. d. Place one Flange Nut on each bolt. 2. Loosen the Tightening Bolt of the Mounting Bracket and open the bracket 90°.
3. Insert the PrismStation into the Mounting Bracket, and then tighten the bolt to lock the PrismStation in place. 4. Mount the PrismStation on the pole and secure it. a. Place the Mounting Bracket against the pole. b. Slide the slot of the Pole Clamp over the adjacent Carriage Bolt. c. Tighten the Flange Nuts of the bolts to 25 N ∙ m to secure the Mounting Bracket to the pole. 25 N ∙ m Note: The mounting assembly can accommodate a Ø 25 - 75 mm pole.
5. Adjust the elevation angle. a. Loosen the Elevation Screw on the bottom of the bracket. Elevation Screw b. Pivot the PrismStation until the Elevation Indicator shows the desired elevation angle. Elevation Indicator c. Tighten the Elevation Screw to 15 N ∙ m. 6. Proceed to the Connecting to Power and GPS section.
Connecting to Power and GPS 1. Remove the port cover by pressing up the latch of the cover and sliding the cover out. 2. Remove the rubber gasket from the port cover.
3. Connect an Ethernet cable to the Ethernet port. 4. Connect the GPS Antenna to the GPS Antenna Connector.
5. Punch out the cutout for the GPS cable. 6. Replace the port cover.
7. Fit the rubber gasket over the Ethernet cable, and then slide the gasket into the port cover. 8. Place the magnetic GPS Antenna on a steel surface near the PrismStation. Note: Ensure that the GPS Antenna has clear line of sight to the sky for proper GPS reception. 9. Connect the power using one of the following options: • Using the included Gigabit PoE Adapter: Go to “Connecting to the PoE Adapter”.
Connecting to the PoE Adapter 1. Connect the Ethernet cable from the PrismStation to the POE port on the PoE Adapter. 2. Connect an Ethernet cable from your LAN to the LAN port on the PoE Adapter. 3. Connect the Power Cord to the PoE Adapter, and then plug the Power Cord into a power outlet. Mounting the PoE Adapter (Optional) 1. Remove the PoE Mounting Bracket from the adapter, place the bracket at the desired location, and mark the two holes. 2.
Accessing airOS via Wi-Fi Verify connectivity in the airOS® Configuration Interface. There are two methods, the U Mobile App and Web Portal. Both are available for 15 minutes immediately after you power on the PrismStation. If necessary, you can power cycle the PrismStation to re-enable its Wi-Fi. Proceed to the appropriate instructions: U Mobile App 1. Download the U Mobile app from the App Store (iOS) or Google Play™ (Android). 2.
5. Tap Connect on the Login screen. 6. Select your Country and tap Done. 7. Customize your settings as needed.
Web Portal 1. Connect your device’s Wi-Fi to the PrismStation SSID named: PS-5AC: Note: Ensure that your Wi-Fi connection has DHCP enabled. 2. Launch your web browser and go to: http://setup.ubnt.com 3. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login. Note: The Country setting for U.S. product versions is restricted to a choice of Canada, Puerto Rico, or the U.S.
Installer Compliance Responsibility Devices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements. The Antenna and Output Power fields are provided to the professional installer to assist in meeting regulatory requirements.
Specifications PS-5AC Dimensions 174 x 174 x 184 mm (6.85 x 6.85 x 7.24") 155 x 155 x 104 mm (5.16 x 5.16 x 4.09") 83 x 117 x 69 mm (3.27 x 4.61 x 2.72") Without Horn Antenna Mounting Hardware* Only Weight Without Horn Antenna Mounting Hardware* Only 1.07 kg (2.36 lb) 0.77 kg (1.70 lb) 0.79 kg (1.74 lb) Gain 14 dBi Beamwidth 45° (Default Horn) Networking Interface (1) 10/100/1000 Ethernet Port RF Connector (1) GPS LED Power Max. Power Consumption Power Supply 10W 24V,0.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
Limited Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation.
Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PUR
Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you.
Industry Canada CAN ICES-3(A)/NMB-3(A) This Class A digital apparatus complies with Canadian CAN ICES-003. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1.
RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 23 cm from all persons and must not be lo cated or operating in conjunction with any other antenna or transmitter. Les antennes utilisées pour ce transmetteur doivent être installé en considérant une distance de séparation de toute personnes d’au moins 23 cm et ne doivent pas être localisé ou utilisé en conflit avec tout autre antenne ou transmetteur.
RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity Česky [Czech] UBIQUITI NETWORKS tímto prohlašuje, že toto UBIQUITI NETWORKS zařízení, je ve shod se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Hermed, UBIQUITI NETWORKS, erklærer at denne UBIQUITI NETWORKS enhed, er i overensstemmelse med de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Malti [Maltese] Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan il-mezz UBIQUITI NETWORKS huwa konformi mar-rekwiżiti essenzjali u dispożizzjonijiet rilevanti oħrajn ta ‘Direttiva 1999/5/KE. Norsk [Norwegian] Herved UBIQUITI NETWORKS, erklærer at denne UBIQUITI NETWORKS enheten, er i samsvar med de grunnleggende kravene og andre relevante bestemmelser i direktiv 1999/5/EF.
