User's Manual

Model: UVC-Micro
Quick Start Guide
®
Package Contents
UVC-Micro
Camera
UVC-Micro
Base
Power
Adapter
Flat Base
Plate
Corner Base
Plate
Mounting
Tape
Screws
(Qty. 5)
Screw
Anchors
(Qty. 5)
Cable Clips
(Qty. 6)
Hardware Overview
LED
Reset
LED When connected and powered by
the UVC-Micro Base, the LED will light
steady blue during the boot up process.
After boot up is finished, the LED will
glow a breathing pattern to indicate
that Wi-Fi is ready.
Note: The LED can be disabled
in the Camera Configuration
Interface.
Reset To reset to factory defaults, press
and hold the Reset button for more than
5 seconds until the LED flashes.
Installation
Install the UVC-Micro within 5 m (16')
of a power outlet. The camera has
a magnetic base that can be used
to mount it on a metal surface and
includes mounting kits for standard
wall or corner mounting. Follow the
appropriate steps for your installation.
Mount on Metal Surface
1. Attach the power cable and the UVC-
Micro Camera to the UVC-Micro Base.
2. Attach the camera assembly to a
metal (steel) surface.
Wall Mounting
Mount with tape or with screws:
Mounting with Tape
1. Remove the paper from one side of
the Mounting Tape, and center the
tape on the back of the Flat Base Plate.
2. Remove the paper from the other
side of the Mounting Tape and attach
the Flat Base Plate to the wall.
Mounting with Screws
1. Place the Flat Base Plate at the desired
location and mark the two mounting
holes.
Note: If you are running the power
cable inside the ceiling or wall,
then mark the cable feed opening
below the mounting holes.
2. Use a 3 mm drill bit to drill a hole at
each mark, and insert a Screw Anchor
into each hole.
3. (Optional) When running the power
cable inside the wall or ceiling, cut the
hole for the power cable. Then feed
the cable through the hole and the
Flat Base Plate.
4. Attach the Flat Base Plate to the
surface by fastening a Screw to each
Screw Anchor.
*640-00157-01*
640-00157-01
Corner Mounting
1. Place the Corner Base Plate at the
desired location and mark the two
mounting holes.
2. Use a 3 mm drill bit to drill a hole at
each mark, and insert a Screw Anchor
into each hole.
3. Feed the power cable through the
back of the Corner Base Plate.
4. Secure the Corner Base Plate by
fastening a Screw to each Screw
Anchor.
Attaching the Camera
1. Attach the power cable to the back of
the UVC-Micro Base.
2. Connect the UVC-Micro Base to the
Base Plate by inserting the mounting
tabs into the slots on the base.
3. Rotate the UVC-Micro Base to lock it.
4. Attach the UVC-Micro Camera to the
UVC-Micro Base, and pivot the camera
to the desired angle.
Connecting Power
The included Power Adapter has a 5 m
(16') power cable that is hidden inside
the adapter casing.
Extend the power cable as needed, by
following these steps:
1. Hold the outer casing of the Power
Adapter with the Ubiquiti® U logo
facing toward you, and push in the
center of the logo until the adapter
releases from the outer casing.
2. Unwind the power cable to extend it
to the desired length. Then lock the
cable into the notch located under
the bottom of the U logo.
3. Slide the outer casing back onto the
adapter until it snaps into place.
4. Plug the Power Adapter into a power
outlet. To secure the connection, use
the outlet cover plate screw to fasten
the Power Adapter to the outlet.
(Optional)
Note: (6) Cable Clips with adhesive
tape are included to help hold
the power cable in place. Remove
the paper backing on each clip to
expose the adhesive tape.
Connect via Wi-Fi
Access the Camera Configuration
Interface using Wi-Fi and a web browser
to configure the camera.
1. Connect your host machine Wi-Fi to
the SSID labeled UVC-Micro-xxxx
(where xxxx is the last four characters
of the MAC address of the UVC-Micro)
2. Launch a web browser and go to:
https://192.168.1.20
3. The login screen will appear. Enter
ubnt in the Username and Password
fields and click Login.