Wall Mount Motion Sensor Model: mFi-MSW
Introduction Introduction Thank you for purchasing the Ubiquiti mFi™ Wall Mount Motion Sensor. This sensor is designed for use with the mFi mPort. Once they are connected, you can use the mFi Controller software to monitor your sensors using your Web browser. Package Contents Wall Mount Motion Sensor Mounting Bracket Mounting Base Jumpers (Qty. 3) Wall Mount Motion Sensor Model: mFi-MSW Quick Start Guide M3x20 mm Screws (Qty. 2) M2.6x8 mm Screws (Qty. 2) Anchors (Qty.
mFi™ Wall Mount Motion Sensor Hardware Overview Front Motion Sensor Back mFi RJ45 Port 2
Hardware Installation Hardware Installation Installation Tips • Avoid installing the sensor in areas where it will face direct or reflected sunlight. • Ensure there are no obstructions in the field of view. • Avoid placing the sensor in areas where the environmental temperature may change rapidly. • Locate the sensor at least 1 meter away from the nearest fluorescent light to avoid interference. Ceiling-Mount 1.
mFi™ Wall Mount Motion Sensor Wall-Mount 1. Use a 6 mm drill bit to drill two holes 20 mm apart with one directly above the other. 20 mm 2. Insert the anchors into the holes. 3. Use a Phillips screwdriver to secure a M3x20 Screw to the top anchor in the wall. Ensure to leave a clearance of approximately 1 mm between the screw head and the anchor.
Hardware Installation 4. Align the top hole of the Mounting Bracket over the screw and slide the Mounting Bracket down. 5. Use the Phillips screwdriver to secure the second M3x20 Screw through the bottom of the Mounting Bracket into the anchor.
mFi™ Wall Mount Motion Sensor Connecting the Cabling and Mounting Base 1. Connect a straight-through CAT5/6 cable to the mFi RJ45 port on the mFi-MSW. 2. Secure the mFi-MSW to the Mounting Base using the two M2.6x8 mm Screws.
Hardware Installation 3. Connect the Mounting Base to the Mounting Bracket. 4. Connect the other end of the CAT5/6 cable from the sensor to an mFi RJ45 port on the mFi mPort. Refer to the User Guide on the CD‑ROM that was included with your mFi mPort for instructions on configuring the mFi‑MSW in the mFi Controller software. The User Guide can also be downloaded from our website at www.ubnt.
mFi™ Wall Mount Motion Sensor Jumper Settings The mFi-MSW has jumpers located inside the product casing. Typically there is no need to open the casing to adjust the jumpers. The SENS and LED jumpers are the only ones that you may want to change. The SENS jumper can be changed to reduce the sensitivity of the microwave sensor. The LED jumper can be turned on so the LED is visible when the motion sensor is triggered.
LED If you need to access the jumper settings, use a Phillips screwdriver to remove the screw at the base of the sensor. Lift the case up and the jumpers will be accessible. LED The LED is disabled by default and can only be enabled by opening the product case and adjusting the jumper. When the LED is enabled, the bottom panel with the sensor will illuminate in one of the following colors when motion is detected. Color Detection Indicates that the microwave sensor detected motion.
mFi™ Wall Mount Motion Sensor Detection Pattern 110°, 10 x 10 m at 25° C Top View Side View 2.3 m 0.5 m 2.
Specifications Specifications mFi-MSW Dimensions Weight 146 x 66 x 52 mm 127 g Power Supply 9 - 16VDC, 12VDC Typical Current Drain 35mA @ 12VDC Infrared Sensor Microwave Sensor Alarm Period Alarm Output Detection Range Mounting Mounting Height Detection Speed RFI Immunity Operating Temperature Humidity Ports Dual Element DRO, Patch Antenna 3 Seconds NC/NO, 24VDC, 0.2A Max. 10 x 10 m, 110° @ 25° C Wall/Ceiling (Kits included) 2.3 m Typical 0.3 to 3.0 m/sec Avg.
mFi™ Wall Mount Motion Sensor General Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) represents and warrants that the Products furnished hereunder shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS sole and exclusive obligation under the foregoing warranty shall be to repair or replace, at its option, any defective Product that fails during the warranty period.
General Warranty Warranty Conditions The foregoing warranty shall apply only if: (I) The Product has not been subjected to misuse, neglect or unusual physical, electrical or electromagnetic stress, or some other type of accident. (II) No modification, alteration or addition has been made to the Product by persons other than UBIQUITI NETWORKS or UBIQUITI NETWORK’S authorized representatives or otherwise approved by UBIQUITI NETWORKS.
mFi™ Wall Mount Motion Sensor Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation.
Compliance This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. this device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numérique de la classe A est confrome à la norme NMB-003 Canada.
mFi™ Wall Mount Motion Sensor L’émetteur-récepteur décrit ici émet de l’énergie de fréquence radio. Bien que le niveau de puissance est faible, l’énergie concentrée à partir d’une antenne directionnelle peut présenter un danger pour la santé. Ne pas permettre aux gens de se rapprocher de 20 cm à l’antenne lorsque l’émetteur est en marche. Des renseignements supplémentaires sur l’exposition aux RF est disponible sur Internet à www.fcc.
Compliance RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
mFi™ Wall Mount Motion Sensor Français La directive européenne 2002/96/CE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages.
Declaration of Conformity English Hereby, UBIQUITI NETWORKS, declares that this UBIQUITI NETWORKS device, is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Eesti [Estonian] Käesolevaga kinnitab UBIQUITI NETWORKS seadme UBIQUITI NETWORKS device, vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
mFi™ Wall Mount Motion Sensor Latviski [Latvian] Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem. Lietuviškai UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI [Lithuanian] NETWORKS įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Ubiquiti Networks Support Email: support@ubnt.com Phone (9 a.m. - 5 p.m. PST): 408-942-1153 Online Resources Wiki Page: wiki.ubnt.com Support Forum: forum.ubnt.com Downloads: downloads.ubnt.com www.ubnt.com © 2012 Ubiquiti Networks, Inc. All rights reserved.
