5 GHz High-Performance Integrated InnerFeed Antenna Model: AGM5-HP-1114
Introduction Introduction Thank you for purchasing the Ubiquiti Networks airGrid™ 5 GHz High-Performance Integrated InnerFeed Antenna, model AGM5-HP-1114. This Quick Start Guide is designed to walk you through the installation of the airGrid. Package Contents 5 GHz High-Performance Integrated InnerFeed Antenna Model: AGM5-HP-1114 11x14" Grid Reflector Antenna Feed* Feed Support* Quick Start Guide L Bracket Pole Clamp M6 U Bolt M6x20 Bolts (Qty. 4) M6 Serrated Flange Nuts (Qty.
airGrid™ AGM5-HP-1114 Quick Start Guide Installation Requirements • 10 mm wrench • Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from the most brutal environments and devastating ESD attacks with industrial‑grade shielded Ethernet cable from Ubiquiti Networks™. For more details, visit www.ubnt.com/toughcable Hardware Installation 1.
Hardware Installation 2. Route an Ethernet cable through the cable opening of the Feed Support and connect it to the Ethernet port on the back of the Antenna Feed.
airGrid™ AGM5-HP-1114 Quick Start Guide 3. Insert the Antenna Feed into the Feed Support until it locks into place. Horizontal Polarization Vertical Polarization WARNING: The orientation of the Antenna Feed and Grid Reflector must match the orientation required for your signal polarization, horizontal or vertical. 4. Wrap the Feed Support Bushing around the Ethernet cable and then push it into the cable opening of the Feed Support.
Hardware Installation 5. Attach the airGrid to the pole. Note: The mounting assembly can accommodate a Ø 1.25" - 2.2" pole. a. Ensure that the cable opening of the Feed Support faces down. b. Insert the M6 U Bolt into the Pole Clamp and L Bracket. c. Secure the M6 U Bolt with two M6 Serrated Flange Nuts. d. Tighten all nuts to approximately 14 N-m (10 lb-ft) or less to avoid deforming the pole.
airGrid™ AGM5-HP-1114 Quick Start Guide Connecting Power over Ethernet 1. Connect the other end of the Ethernet cable from the airGrid to the Ethernet port labeled POE on the PoE Adapter. 2. Connect an Ethernet cable from your LAN to the Ethernet port labeled LAN on the PoE Adapter. 3. Connect the Power Cord to the power port on the PoE Adapter. Connect the other end of the Power Cord to a power outlet.
Accessing airOS Accessing airOS Verify connectivity in the airOS Configuration Interface. 1. Make sure that your host machine is connected via Ethernet to the airGrid. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet. 3. Launch your web browser and type http://192.168.1.20 in the address field. Press enter (PC) or return (Mac). 4. The login screen will appear. Enter ubnt in the Username and Password fields. Select your Country and Language.
airGrid™ AGM5-HP-1114 Quick Start Guide 5. Click the Wireless tab. From the Antenna drop-down, select the size of Grid Reflector you are using. Click Change to save. You can customize additional settings as needed. Installer Compliance Responsibility Devices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements.
Specifications Specifications AGM5-HP-1114 Dimensions 370 x 270 x 264 mm (Mount Included) Weight 1.440 kg (Mount Included) Networking Interface Enclosure (1) 10/100 Ethernet Port Outdoor UV Stabilized Plastic Frequency 5470 – 5825 MHz* Gain 23 dBi Output Power 25 dBm Max. Power Consumption Power Supply Power Method 3.0 W 24V, 0.5A PoE Adapter (Included) Passive Power over Ethernet (Pairs 4, 5+; 7, 8 Return) Max. VSWR 1.
airGrid™ AGM5-HP-1114 Quick Start Guide Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. 2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician. 3.
Compliance No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned to Buyer freight collect. UBIQUITI NETWORKS shall have no obligation to make repairs or replacement necessitated by catastrophe, fault, negligence, misuse, abuse, or accident by Buyer, Buyer’s customers or any other parties.
airGrid™ AGM5-HP-1114 Quick Start Guide NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Compliance RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 2.52 m from all persons and must not be located or operating in conjunction with any other antenna or transmitter. Les antennes utilisées pour ce transmetteur doivent être installé en considérant une distance de séparation de toute personnes d'au moins 2.52 m et ne doivent pas être localisé ou utilisé en conflit avec tout autre antenne ou transmetteur.
airGrid™ AGM5-HP-1114 Quick Start Guide Deutsch Die Europäische Richtlinie 2002/96/EC verlangt, dass technische Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist , nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte.
Declaration of Conformity Italiano La direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici.
airGrid™ AGM5-HP-1114 Quick Start Guide Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ UBIQUITI NETWORKS ΔΗΛΩΝΕΙ ΟΤΙ UBIQUITI NETWORKS device, ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1995/5/ΕΚ. Magyar [Hungarian] Alulírott, UBIQUITI NETWORKS nyilatkozom, hogy a UBIQUITI NETWORKS device, megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Ubiquiti Networks Support Email: support@ubnt.com Phone (9 a.m. - 5 p.m. PST): 408-942-1153 Online Resources Wiki Page: wiki.ubnt.com Support Forum: forum.ubnt.com Downloads: downloads.ubnt.com www.ubnt.com © 2012 Ubiquiti Networks, Inc. All rights reserved.
