3-Port Router Model: ERLite-3
Introduction Thank you for purchasing the Ubiquiti Networks® EdgeRouter™ Lite. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents eth0 eth1 eth2 EdgeRouter Lite Screw Anchors (M2.9, Qty. 2) Screws (M2.9x20, Qty. 2) 3-Port Router Model: ERLite-3 Power Adapter (12V, 1A) Power Cord Quick Start Guide TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above).
Hardware Overview Front Panel Ports Ethernet (eth0-eth2) Console eth0 eth1 Reset eth2 Interface Description Console RJ45 serial console port for Command Line Interface (CLI) management. Use a RJ45‑to‑DB9, serial console cable, also known as a rollover cable, to connect the Console port to your computer. (If your computer does not have a DB9 port, then you will also need a DB9 adapter.
Interface Reset Description There are two methods to reset the EdgeRouter Lite to factory defaults: • Runtime reset (recommended) The EdgeRouter Lite should be running after bootup is complete. Press and hold the Reset button for about 10 seconds until the right LED on port eth2 starts flashing and then becomes solidly lit. After a few seconds, the LED will turn off, and the EdgeRouter Lite will automatically reboot. • Power-on reset Disconnect the Power Cord from the Power Adapter.
Front Panel LEDs The LEDs on the left side of each port are not used at this time. Below is a description of the right LED functionality: Speed/Link/Act 10/100 Mbps Power Speed/Link/Act 1000 Mbps eth0 Ethernet (0-2) Console LED eth2 State Status Off EdgeRouter Lite not powered on. Green EdgeRouter Lite is powered on.
Back Panel Ventilation Holes Grounding Point 12V DC Hardware Installation Mount the EdgeRouter Lite on a wall or place it on top of a bench. WARNING: FAILURE TO PROVIDE PROPER VENTILATION MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF CLEARANCE NEXT TO THE VENTILATION HOLES FOR ADEQUATE AIRFLOW. Cabling Requirements • For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use.
Wall Mounting To mount the EdgeRouter Lite on a wall, you will need a drill, a 6 mm drill bit, and a Phillips screwdriver. 1. Use a 6 mm drill bit to drill two holes 100 mm apart. 2. Insert the Screw Anchors into the holes. Use a Phillips screwdriver to secure a Screw to each anchor. Leave a clearance of approximately 3 mm between each screw head and its anchor. 100 mm 3 mm Note: You can also mount the EdgeRouter Lite in a vertical orientation. 3.
Grounding the EdgeRouter Lite (Recommended) The EdgeRouter Lite is grounded through the Power Adapter; however, you can add optional ESD grounding for enhanced ESD protection. 1. Loosen the grounding screw to secure a ground wire (not included) to the Grounding Point. 2. Secure the other end of the ground wire to a grounding block. Connecting Power 1. Connect the Power Adapter to the Power port.
2. Connect the Power Cord to the Power Adapter. Connect the other end of the Power Cord to a power outlet. Accessing the EdgeOS Configuration Interface 1. Connect an Ethernet cable from the Ethernet port of your computer to the port labeled eth0 on the EdgeRouter Lite. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet (e.g., 192.168.1.100). 3. Launch your web browser. Type https://192.168.1.1 in the address field. Press enter (PC) or return (Mac).
4. The login screen will appear. Enter ubnt in the Username and Password fields. Read the Ubiquiti License Agreement, and check the box next to I agree to the terms of this License Agreement to accept it. Click Login. The EdgeOS Configuration Interface will appear, allowing you to customize your settings as needed. Refer to the EdgeRouter Lite User Guide for instructions on configuring the EdgeRouter Lite. The User Guide is available at documentation.ubnt.
Specifications EdgeRouter Lite Dimensions Weight Processor System Memory Code Storage Power Input Button Wall Mount Certifications Operating Temperature Operating Humidity 200 x 90 x 30 mm (7.87 x 3.54 x 1.18") 345 g (12.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Failure to provide proper ventilation may cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. WARNING: Do not use this product in location that can be submerged by water.
Limited Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation.
Returns No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS’ facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal.
Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity Česky [Czech] UBIQUITI NETWORKS tímto prohlašuje, že toto UBIQUITI NETWORKS zařízení, je ve shod se základními požadavky a dalšími příslušnými ustanoveními směrnic 2014/30/EU, 2014/35/EU. Dansk [Danish] Hermed, UBIQUITI NETWORKS, erklærer at denne UBIQUITI NETWORKS enhed, er i overensstemmelse med de væsentlige krav og øvrige relevante krav i direktiver 2014/30/EU, 2014/35/EU.
Malti [Maltese] Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan il-mezz UBIQUITI NETWORKS huwa konformi mar-rekwiżiti essenzjali u dispożizzjonijiet rilevanti oħrajn ta ‘Direttivi 2014/30/UE, 2014/35/UE. Herved UBIQUITI NETWORKS, erklærer at denne UBIQUITI NETWORKS Norsk [Norwegian] enheten, er i samsvar med de grunnleggende kravene og andre relevante bestemmelser i direktivene 2014/30/EU, 2014/35/EU.
