Advanced Gigabit Ethernet Router Model: ER-X
Introduction Thank you for purchasing the Ubiquiti Networks® EdgeRouter™ X. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents EdgeRouter X Power Adapter (12V, 0.5A) Installation Requirements • For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use. • For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections.
Hardware Overview Power Ethernet (eth0-eth4) State Status Power Off Power Off Green Power On eth0-eth4 Top Panel Off No Link Green Link Established at 10/100/1000 Mbps Flashing Indicates Activity LED Front Panel Ethernet (eth0/PoE In) Port eth0/PoE In eth1-3 eth4/PoE Out Ethernet (eth1-eth3) Ethernet (eth4/PoE Out) Description RJ45 port accepts 24V passive PoE and supports a 10/100/1000 Ethernet connection. RJ45 ports support 10/100/1000 Ethernet connections.
Passive PoE Passthrough The EdgeRouter can be powered by either method: • Power adapter • 24V passive PoE on the eth0/PoE In port Passive PoE output on port eth4/PoE Out works as a passthrough and depends on the input power source. If the included Power Adapter (12V, 0.5A) is used, there may not be sufficient passthrough to power another device because the EdgeRouter can consume up to 5 watts on its own.
Back Panel Reset Button Ground Power Description There are two methods to reset the EdgeRouter to factory defaults: Reset Detail Ground Power • Runtime reset (recommended) The EdgeRouter should be running after bootup is complete. Press and hold the Reset button for about 10 seconds until the eth4 LED starts flashing and then becomes solidly lit. After a few seconds, the LED will turn off, and the EdgeRouter will automatically reboot. • Power-on reset Disconnect power from the EdgeRouter.
Hardware Installation Place the EdgeRouter on a flat, horizontal surface or mount it on a wall (mounting screws not included). WARNING: FAILURE TO PROVIDE PROPER VENTILATION MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF CLEARANCE NEXT TO THE VENTILATION HOLES FOR ADEQUATE AIRFLOW. Connecting Power Follow the appropriate instructions for your installation: Connecting Power Using the Power Adapter Connect the Power Adapter to the Power port of the EdgeRouter. Then plug the Power Adapter into a power outlet.
Accessing the EdgeOS Configuration Interface The EdgeOS® configuration interface can be accessed via DHCP or static IP address assignment. By default, eth1 is set up as a DHCP client, while eth0 is assigned a static IP address of 192.168.1.1. To configure the EdgeRouter, proceed to the appropriate section: DHCP or “Static IP Address”. DHCP 1. Connect an Ethernet cable from eth1 on the EdgeRouter to a LAN segment that has an existing DHCP server. 2.
4. The login screen will appear. Enter ubnt in the Username and Password fields. Read the Ubiquiti License Agreement, and check the box next to I agree to the terms of this License Agreement to accept it. Click Login. The EdgeOS Configuration Interface will appear, allowing you to customize your settings as needed. For more information, refer to the EdgeOS User Guide, which is available at www.ubnt.com/download/edgemax You can also manage your device using the Ubiquiti® Network Management System.
Static IP Address 1. Connect an Ethernet cable from the Ethernet port on your computer to the port labeled eth0/PoE In on the EdgeRouter. If you are using PoE, then connect your computer to the PoE switch or adapter. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet. 3. Launch your web browser. Type https://192.168.1.1 in the address field, and press enter (PC) or return (Mac). 4. The login screen will appear.
Specifications EdgeRouter X Dimensions Weight Max. Power Consumption Power Input Power Supply Supported Voltage Range Button LED Processor System Memory Code Storage Wall-Mount Networking Interfaces Data/PoE Input Port Data Ports Data/PoE Passthrough Port Operating Temperature Operating Humidity Certifications 110 x 75 x 22 mm (4.33 x 2.95 x 0.87") 175g (6.17 oz) 5W 12VDC, 0.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Failure to provide proper ventilation may cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. WARNING: Do not use this product in a location that can be submerged by water.
Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. 2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician. 3.
Limited Warranty www.ubnt.com/support/warranty/ The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че това устройство ER-X е в съответствие със съществените изисквания и други приложими разпоредби на Директиви 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.ubnt.
Íslenska [Icelandic] Hér, UBIQUITI NETWORKS, því yfir að þetta ER-X tæki er í samræmi við grunnkröfur og önnur viðeigandi ákvæði tilskipana 2014/30/ESB, 2014/35/ESB. Fullur texti ESB samræmisyfirlýsing er að finna á eftirfarandi netfangi: www.ubnt.com/compliance Italiano [Italian] Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo ER-X, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti delle direttive 2014/30/UE, 2014/35/UE.
www.ubnt.com Ubiquiti Networks, Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA ©2014-2018 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, EdgeMAX, EdgeOS, EdgeRouter, TOUGHCable, and UNMS are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their respective owners.
